KidKraft BROCKWELL User manual

INSTALLATION AND OPERATING INSTRUCTIONS
BROCKWELL – F24810/PRESTON – F24800/
TWIN MOUNTAIN LODGE – F25700Z
Rev 07/05/20199404815
Table of Contents
Warnings and Safe Play Instructions..........pg. 3
Protective Surfacing Guidelines. . . . . . . . . . . . . . . pg. 4
Instructions for Proper Maintenance .........pg. 5
About Our Wood – Limited Warranty.........pg. 6
Keys to Assembly Success ....................pg. 7
Part ID .......................................pg. 9
Step-By-Step Instructions ...................pg. 18
Installation of I.D./Warning Plaque......Final Step
WARNING
10 - 12 Hrs
FOR FORT & SWING
TWO PERSON
ASSEMBLY
2-4 Hrs
10 - 12 Hrs
FOR FORT & SWING
TWO PERSON
ASSEMBLY
10 - 12 Hrs
FOR FORT & SWING
2 - 4 Hrs
TUBE SLIDE
TWIN MOUNTAIN LODGE
BROCKWELL PRESTON
To reduce the risk of serious injury or death, you must read and follow these instrucons.
Keep and refer to these instrucons oen and give them to any future owner of this play set.
Manufacturer contact informaon provided below.
OBSTACLE FREE SAFETY ZONE -30’ 9” x 27’1” (9.37 x 8.23 m) area requires Protecve Surfacing. See page 3.
MAXIMUM VERTICAL FALL HEIGHT - 6’ 7” (2.01 m)
CAPACITY - 12 Users Maximum, Ages 3 to 10; Weight Limit 110 lbs. (49.9 kg) per child.
RESIDENTIAL HOME USE ONLY. Not intended for public areas such as mul-unit residences, schools, churches, nurseries, day cares or parks.
Warning. Only for domesc use.
Required:
53” Add On A (A24815)
53” Add On B (A24816)
53” Add On C (A24817)
53” Add On D (A24818)
53” Add On G (A24821)
Required:
53” Add On A (A24815)
53” Add On B (A24816)
53” Add On C (A24817)
53” Add On D (A24818)
53” Add On E (A24819)
Required:
53” Add On A (A24815)
53” Add On B (A24816)
53” Add On C (A24817)
53” Add On E (A24819)
53” Add On F (A24820)
KidKraft, Inc.
4630 Olin Road
Dallas, Texas 75244 USA
[email protected]
[email protected]
1.800.933.0771
972.385.0100
For online parts replacement visit
https://parts.kidkraft.com/
KidKraft Netherlands BV
Olympisch Stadion 29
1076DE Amsterdam
The Netherlands
[email protected]
[phone] M-F from 09:00 to 17:30
(GMT+1)
For online parts replacement visit
https://parts.kidkraft.eu/

ALTERNATE CONFIGURATIONS USING
BROCKWELL/PRESTON/TWIN MOUNTAIN LODGE
FOLLOW INSTRUCTIONS FOR BROCKWELL :
REQUIRED:
A24815 - 53’’ Add on A
A24816 - 53’’ Add on B
A24817 - 53’’ Add on C
A24819 - 53’’ Add on E
A24820 - 53’’ Add on F
A25230 - Adventure Tunnel
F24825 - LANGDON RETREAT
F24826 - HUNTINGTON RESORT
F24827 - CEDAR GROVE MANOR
F24828 -ORCHARD VIEW MANOR
FOLLOW INSTRUCTIONS FOR BROCKWELL :
REQUIRED:
A24815 - 53’’ Add on A
A24816 - 53’’ Add on B
A24817 - 53’’ Add on C
A24819 - 53’’ Add on E
A24820 - 53’’ Add on F
A25230 - Adventure Tunnel
FOLLOW INSTRUCTIONS FOR PRESTON :
REQUIRED:
A24815 - 53’’ Add on A
A24816 - 53’’ Add on B
A24817 - 53’’ Add on C
A24818 - 53’’ Add on D
A24821 - 53’’ Add on G
A25230 - Adventure Tunnel
FOLLOW INSTRUCTIONS FOR TWIN MOUNTAIN
LODGE :
REQUIRED:
A24815 - 53’’ Add on A
A24816 - 53’’ Add on B
A24817 - 53’’ Add on C
A24818 - 53’’ Add on D
A24819 - 53’’ Add on E
A25230 - Adventure Tunnel
KidKraft, Inc.
4630 Olin Road
Dallas, Texas 75244 USA
[email protected]
[email protected]
1.800.933.0771
972.385.0100
For online parts replacement visit
https://parts.kidkraft.com/
KidKraft Netherlands BV
Olympisch Stadion 29
1076DE Amsterdam
The Netherlands
[email protected]
[phone] M-F from 09:00 to 17:30
(GMT+1)
For online parts replacement visit
https://parts.kidkraft.eu/

3
Warnings and Safe Play Instructions
CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred
while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying
with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using
this play system. Go over the warnings and safe play instructions regularly with your children and make certain that they
understand and follow them. Remember on-site adult supervision is required for children of all ages.
SERIOUS HEAD INJURY HAZARD
Installation over concrete, asphalt, dirt, grass, carpet
and other hard surface creates a risk of serious injury
or death from falls to the ground. Install and maintain
shock absorbing material under and around play-set as
recommended on page 3 of these instructions.
COLLISION HAZARD
Place play-set on level ground at least 2m from any
obstruction such as a garage or house, fences, poles,
trees, sidewalks, walls, landscape timbers, rocks,
pavement, planters, garden borders, overhanging
branches, laundry lines, and electrical wires. (See
OBSTACLE FREE SAFETY ZONE on cover)
CHOKING HAZARD/SHARP EDGES & POINTS
Adult assembly required. This product contains small
parts and parts with sharp edges and points. Keep parts
away from children until fully assembled.
WARNING LABEL
Owners shall be responsible for maintaining the legibility
of the warning labels.
STRANGULATION HAZARD
,seni lsehtolc,seporht iwyalpotnerdl ihcwol laREVEN•
pet leashes, cables, chains or cord-like items when using
this play-set or to attach these items to play-set.
ponchos, hoods, scarves, capes, necklaces, items with
draw-strings, cords or ties when using this play-set.
stemlehtropsroekibraewotnerdl ihcwol laREVEN•
when using this play-set.
Failure to prohibit these items, even helmets with chin
straps, increases the risk of serious injury and death to
children from entanglement and strangulation.
TIP OVER HAZARD
Choose a level location for the equipment. This can reduce
the likelihood of the play set tipping over and loose-fill
surfacing materials washing away during heavy rains.
DO NOT allow children to play on the play-set until the
assembly is complete and the unit is properly anchored.
Never add extra length to chain or rope. The chains or ropes
provided are the maximum length designed for the swinging
element(s).
WARNING
eeS. t es- ya l pruoyfosno i t a t imi ly t i capacevresbO
front cover.
gn i so l cnet oo f l l u fdnagn i t t fil l ewh t iwne r d l i hcsse rD
footwear.
retnecehtnithgiewl lufr iehtht iwt i sotnerdl ihchcaeT
of the swing seat to prevent erratic swing motion or
falling off.
,gn i ss im; doowdekcarcronekorb, dere tn i l psro fkcehC
loose, or sharp edged hardware. Replace, tighten and or
sand smooth as required prior to playing.
n i ahc, s r edda lepo r, seporgn i bmi l cdednepsust ah ty f i r eV
or cable are secured at both ends and cannot be looped
back on itself as to create an entanglement hazard.
r eh t odnaed i l seh tkcehc, syadt ohrodnaynnusnO
plastic rides to assure that they are not very hot as to
cause burns. Cool hot slide and rides with water and wipe
dry prior to using.
r aewt oo f l eehroeo tnepor aewo tne rd l i hcwo l l at onoD
like sandals, flip–flops or clogs.
dniheb,neewteb, tnorfni,klawotnerdl ihcwol latonoD
or close to moving rides.
poolroseporrosniahcgniwstsiwtnerdl ihcteltonoD
them over the top support bar. This may reduce the
strength of the chain or rope and cause premature failure.
.noi tomnierayehtel ihwsedi rf fotegnerdl ihcteltonoD
. t ews i t inehwt nemp i uqenogn i bmi l ct imr ept onoD
an i t nemp i uqef oesur oya l phguo rt imr ept onoD
manner for which it was not intended. Standing on or
jumping from the roof, elevated platforms, swings,
climbers, ladders or slide can be dangerous.
.staesrosedi rytpmegniwsotnerdl ihcwol latonoD
rotsrfidaehed i l snwodogo tne rd l i hcwo l l at onoD
run up slide.
WARNING – Safe Play Instructions
Orientate slide such that it gets the least amount of exposure
to the sun.

4
One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing
protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable
for the equipment height in accordance with ASTM F1292. There are different types of surfacing to choose from; whichever
product you select, follow these guidelines:
Loose-Fill Materials
• Maintain a minimum depth of 9 inches of loose-fill materials such as wood mulch/chips, engineered wood fiber (EWF), or
shredded/recycled rubber mulch for equipment up to 8 feet high; and 9 inches of sand or pea gravel for equipment up to 5 feet
high. NOTE: An initial fill level of 12 inches will compress to about a 9-inch depth of surfacing over time. The surfacing will also
compact, displace, and settle, and should be periodically raked and refilled to maintain at least a 9-inch depth.
• Use a minimum of 6 inches of protective surfacing for play equipment less than 4 feet in height. If maintained properly, this
should be adequate. (At depths less than 6 inches, the protective material is too easily displaced or compacted.)
NOTE: Do not install home playground equipment over concrete, asphalt, or any other hard surface. A fall onto a hard surface
can result in serious injury to the equipment user. Grass and dirt are not considered protective surfacing because wear and
environmental factors can reduce their shock absorbing effectiveness. Carpeting and thin mats are not adequate protective
surfacing. Ground level equipment -- such as a sandbox, activity wall, playhouse or other equipment that has no elevated play
surface -- does not need any protective surfacing.
• Use containment, such as digging out around the perimeter and/or lining the perimeter with landscape edging. Don’t forget to
account for water drainage.
• Periodically rake, check and maintain the depth of the loose-fill surfacing material. Marking the correct depth on the play
equipment support posts will help you to see when the material has settled and needs to be raked and or replenished. Be sure to
rake and evenly redistribute the surfacing in heavily used areas.
• Do not install loose fill surfacing over hard surfaces such as concrete or asphalt.
Poured-In-Place Surfaces or Pre-Manufactured Rubber Tiles
You may be interested in using surfacing other than loose-fill materials - like rubber tiles or poured-in-place surfaces.
• Installations of these surfaces generally require a professional and are not “do-it yourself” projects.
• Review surface specifications before purchasing this type of surfacing. Ask the installer/manufacturer for a report showing that
the product has been tested to the following safety standard: ASTM F1292 Standard Specification for Impact Attenuation of
Surfacing Materials within the Use Zone of Playground Equipment. This report should show the specific height for which the
surface is intended to protect against serious head injury. This height should be equal to or greater than the fall height - vertical
distance between a designated play surface (elevated surface for standing, sitting, or climbing) and the protective surfacing
below - of your play equipment.
• Check the protective surfacing frequently for wear.
Placement
Proper placement and maintenance of protective surfacing is essential. Refer to diagram on front cover. Be sure to;
• Extend surfacing at least 2m from the equipment in all directions.
• For to-fro swings, extend protective surfacing in front of and behind the swing to a distance equal to twice the height of the top bar
from which the swing is suspended.
• For tire swings, extend surfacing in a circle whose radius is equal to the height of the suspending chain or rope, plus 6 feet in all
directions.
From the CPSC Outdoor Home Playground Safety Handbook. At http://www.playgroundregs.com/resources/CPSC%20324.pdf
Protective Surfacing - Reducing Risk of Serious Head Injury From Falls.
2H 2H
H
Denotes Use Zone with Protective Surfacing
Use Zone for Single-Axis Swings
6 ft.
6 ft.
6 ft.
6 ft.
Denotes Use Zone with Protective Surfacing
Use Zone for Multi-Axis Swings
6 ft. 6 ft.
6 ft.
L

5
Instructions for Proper Maintenance
HARDWARE:
Check metal parts for rust. If found,
sand and repaint using a non-lead
paint complying with 16 CFR 1303.
Inspect and tighten all hardware. On
wood assemblies DO NOT OVER-
TIGHTEN as to cause crushing and
splintering of wood.
Check for sharp edges or protruding screw threads, add
washers if required.
SHOCK ABSORBING SURFACING:
Check for foreign objects. Rake and check depth of loose
fill protective surfacing materials to prevent compaction
and maintain appropriate depth. Replace as necessary.
(See Protective Surfacing, page 3)
GROUND STAKES (ANCHORS):
Check for looseness, damage or deterioration. Should
firmly anchor unit to ground during use. Re-secure and
or replace, if necessary.
SWING HANGERS:
Check that bolts are secure and tight. Quick clips should
be completely closed and threaded clips screwed tight.
If squeaking occurs lubricate bushings with oil or WD-40®.
SWINGS, ROPES AND RIDES:
Reinstall if removed during cold season. Check all
moving parts including swing seats, ropes, chains and
attachments for wear, rust and other deterioration.
Replace as needed.
Check that ropes are tight, secure at both ends and
cannot loop back as to create an entrapment.
WOOD PARTS:
Check all wood members for deterioration, structural
damage and splintering. Sand down splinters and replace
deteriorated wood members. As with all wood, some
checking and small cracks in grain is normal.
Unprotected, they will appear weathered over time.
Periodic application of an exterior water repellent or stain
(water-based) will help improve appearance and life.
Your KidKraft Play System is designed and constructed of quality materials with your child’s safety in mind. As with all outdoor
products used by children, it will weather and wear. To maximize the enjoyment, safety and life of your Play Set, it is important
that you, the owner, properly maintain it.
Check the following at the beginning of the play season:
HARDWARE:
Inspect for tightness. Must be firmly against, but not
crushing the wood. DO NOT OVER-TIGHTEN.
This will cause splintering of wood.
Check for sharp edges or protruding screw threads.
Add washers if required.
SHOCK ABSORBING SURFACING:
Rake and check depth of loose fill protective surfacing
materials to prevent compaction and maintain appropriate
depth. Replace as necessary.
(See Protective Surfacing, page 3)
Check twice a month during play season:
SWING HANGERS:
Check that they are secure and orientated correctly. Hook
should rotate freely and perpendicular to support beam.
If squeaking occurs lubricate bushings with oil or WD-40®.
SWINGS AND RIDES:
Check swing seats, all ropes, chains and attachments for
fraying, wear, excessive corrosion or damage.
Replace if structurally damaged or deteriorated.
Check once a month during play season:
SWINGS AND RIDES:
To prolong their life, remove swings and store inside
when outside temperature is below 32°F/0°C. Below
freezing, plastic parts may become more brittle.
SHOCK ABSORBING SURFACING:
Rake and check depth of loose fill protective surfacing
materials to prevent compaction and maintain appropriate
depth. Replace as necessary.
(See Protective Surfacing, page 3)
Check at the end of the play season:
If you dispose of your play set: Please disassemble and dispose of your unit so that it does not create any unreasonable hazards
at the time it is discarded. Be sure to follow your local waste ordinances.
Use an extra
Flat Washer
If Bolt protrudes
beyond T-Nut

6
About Our Wood
KidKraft Premium Play Systems uses only premium playset lumber, ensuring the safest product for your children’s use. Although we
take great care in selecting the best quality lumber available, wood is still a product of nature and susceptible
to weathering which can change the appearance of your set.
What causes weathering? Does it affect the strength of my Play System?
One of the main reasons for weathering is the effects of water (moisture); the moisture content of the wood at the surface is
different than the interior of the wood. As the climate changes, moisture moves in or out of the wood, causing tension which can
result in checking and or warping. You can expect the following due to weathering. These changes will not affect the strength of
the product:
1. Checking is surface cracks in the wood along the grain. A post (4” x 4”)will experience more checking than a board (1” x 4”)
because the surface and interiormoisture content will vary more widely than in thinner wood.
2. Warping results from any distortion (twisting, cupping) from the original plane ofthe board and often happens from rapid
wettingand drying of the wood.
3. Fading happens as a natural change in the wood coloras it is exposed tosun-light and will turn a grey over time.
How can I reduce the amount of weathering to my Play System?
At the factory we have coated the wood with a water repellent or stain. This coating decreases the amount of water absorption
during rain or snow thus decreasing the tension in the wood. Sunlight will break down the coating, so we recommend applying a
water repellent or stain on a yearly basis (see your local stain and paint supplier for a recommended product).
Most weathering is just the normal result of nature and will not affect safe play and enjoyment for your child. However if you are
concerned that a part has experienced a severe weathering problem please call our consumer relations department for further assistance.
Complete and mail registration card to receive important product notifications and assure prompt
warranty service.
5 Year Limited Warranty
KidKraft warrants that this product is free from defect in materials and workmanship for a period of one
year from the original date of purchase. In addition, lumber is warranted for 5 years against structural
failure due to rot and insect damage. All other parts, such as hardware, swings, rides, accessories, and
slides carry a one-year warranty only.
This warranty applies to the original owner and registrant and is non-transferable.
Regular maintenance is required to assure the integrity of your Play System. This warranty does not
cover any inspection cost.
This Limited Warranty does not cover:
•Labor for replacement of any defective item(s);
•Incidental orconsequential damages;
•Cosmetic defects whichdo not affect performance or integrity;
•Vandalism; improper use or installation; acts of nature;
•Minortwisting, warping, checking,or any other natural occurring properties of wood that do not
affect performance or integrity.
KidKraft products have been designed for safety and quality. Any modifications made to the original
product could damage the structural integrity of the unit leading to failure and possible injury.
Kidkraft cannot assume any responsibility for modified products. Furthermore, modification voids
any and all warranties.
This product is warranted for RESIDENTIAL USE ONLY. Under no circumstance should a
KidKraft Play System be used in public settings such as schools, churches, playgrounds, parks, day
cares and the like. Such use may lead to product failure and potential injury. Any and all public use
will void this warranty.
KidKraft disclaims all other representations and warranties of any kind, express or implied.
This Warranty gives you specific legal rights. You may have otherrights as well which vary from state to state or
province to province. This warranty excludes all consequential damages, however, some states do notallow the
limitation or exclusion ofconsequential damages, andtherefore this limitation may not apply to you.

7
Part Identication Key
On each page, you will nd the parts
and quantities required to complete
the assembly step illustrated on that
page. Here is a sample.
Symbols
Throughout these instructions symbols are provided as important reminders for proper and safe assembly.
Proper Hardware Assembly
Lag screws require drilling pilot
holes to avoid splitting wood. Only a
at washer is required. For ease of
installation liquid soap can be used
on all lag-type screws.
For bolts, tap T-Nut into hole with
hammer. Insert the hex bolt through
lock washer rst then at washer
then hole. Because the assemblies
need to be squared do not completely
tighten until instructed. Pay close
attention to diameter of the bolts.
5/16” is slightly larger than 1/4”.
Note: Wafer head bolts with blue lock
tight or a bolt with a Ny-Lok nut do
NOT require a lock washer.
Once the assembly is tightened, watch for exposed
threads. If a thread protrudes from the T-Nut, remove
the bolt and add washers to eliminate this condition.
Extra washers have been provided for this purpose.
This identies information that requires
special attention. Improper assembly could
lead to an unsafe or dangerous condition.
Where this is shown, 2 or 3
people are required to safely
complete the step. To avoid
injury or damage to the
assembly make sure to
get help!
Check that assembly is square
before tightening bolts.
Use a measuring tape to
assure proper location.
Check that set or assembly is properly level
before proceeding.
Pre-drill a pilot hole
before fastening screw
or lag to prevent
splitting of wood.
This indicates time to tighten bolts, but
not too tight! Do not crush the wood.
This may create splinters and cause
structural damage.
Use
Help
Use
Help
Measure
Distance
Square
Assembly
Use
Level
Pre-drill 1/8” & 3/16” Bit
Tighten
Bolts
No Yes
CAUTION – Protrusion Hazard
Keys to Assembly Success
Tools Required
• Tape Measure
• Carpenters Level
• Carpenters Square
• Claw Hammer
• Standard or Cordless Drill
• #1, #2 & #3 Phillips
or Robertson Bits
or Screwdriver
• Ratchet with extension
(1/2” & 9/16” sockets)
• Open End Wrench
(7/16”, 1/2” & 9/16”)
• Adjustable Wrench
• 1/8” & 3/16” Drill Bits
• Pencil
• 3/16” Hex Key
• 8’ Step Ladder
• Safety Glasses
• Adult Helpers
Quantity Key Number Part Description,
Part Size
2X 012 Post 2 x 4 x 83”
Use an extra
Flat W asher
If Bolt protrudes
beyond T-Nut
Lag Screw
Flat Washer
Lag Assembly
Before mounting Lag Screw,
use factory drilled holes as
guides to drill 1/8” pilot holes
Hex Bolt Bolt Assembly
T-Nut
(Hammer into place)
Do not crush wood!
Lock
Washer
Flat
Washer

8
Key Number: The rst two digits represent the step
number. The third digit represents the order in which
the part is listed in the step.
Note that if the part is used in multiple steps then
the key number only reects the rst step it is used in.
Part Quantity Key Number
Order Listed
(The order the part is
listed in step 1)
Part Description Part Size
2X 012 Post 2 x 4 x 83”
7
Your Key To Quick Assembly
SAVE TIME - TIP #1:
Open each box with wood parts and look for the Key Number
stamped on the end of the wood part (see chart below). Sort
each wood part into the different assembly steps.
SAVE TIME - TIP #2:
In addition to the key number stamp, you can also identify
the wood parts by using the Parts Identication pages in the
manual.
HARDWARE:
The majority of each hardware part comes packed in a separate
bag so you do not need to sort the hardware. Each assembly step
indicates which hardware (bolt, screw, washer etc.) you will require
to complete the step.
SORTING WOOD PARTS INTO
EACH ASSEMBLY STEP WILL
SAVE TIME!
Step Step Step
01 2
Step Number
(This is Step 1)

9
(2) 152 - 4 x 4 x 92" - SW Post - 3599070
(1) 020 - 1-3/8 x 2-1/2 x 57-53/64 " - Left Access - 3599054
(1) 021 - 1-3/8 x 2-1/2 x 57-53/64 " - Right Access - 3599055
(1) 160 - 2-1/2 x 3 x 51" - Support Cross - 3599067
(1) 024 - 1-3/8 x 2-1/2 x 57-53/64" - Rock Rail - 3599058
(2) 061 - 2 x 2 x 63" - Side Joist - 3599064
(1) 130 - 2 x 2 x 39-5/8" - Table Support - 3592612
(1) 140 - 4 x 6 x 92" - Engineered SW Beam - 3599049
1x
- DX Swing Hangers
with Quick Links (6 Pk)
(3201950)
2x 20" chain -Green
1x - Welded Chain Bag (3200173) Green
4x 48" chain -Green
1x - Small Jamb Mount
(2 Pk) (3205947)
1x - Corner
Bracket (3 Pk)
(3205970)
2x - Narrow Angle
Bracket (2 Pk)
(3205939)
1x - Flat Panel Bracket
(5 Pk)(3205935)
1x - Bracket Set (3205700)
2X - Corner
Panel
Bracket (4 Pk)
(3205975)
1x - Acro Bar
(9200131) Green
2x - Heavy Flat Bracket
(9200149)
1x - Heavy C-Bracket
(9200153)
3x - Heavy L-Bracket
(9200151)
1x - Heavy Bracket Set
(3205701) Green
2x - Steel Hand Grip
(9200211) -Yellow
1x - Quick Links w.
Thread (2pk)
(3200022)
1x - Rebar Ground
Stake (6 Pk)
(3200318)
2x 9201712
Door Hinge -Green
9207713
Door Catch -Brown
2x 9201711
Door Handle -Green
1x Magnetic Catch
1x Catch Plate
1x - Door Hardware (3201710)
1x - TNR 3 Post Mount
(9200257) -Yellow
1x - TNR 3 Tube Support
(9200258) -Yellow
1x - KidKraft
Plaque (3320353)
1x - KidKraft
ID Plaque (9320374)
(Reduced Size)

10
(2) G5 -
Hex Bolt 5/16 x 4-1/2"
- (53703342)
(4) H1 -
Hex Bolt 1/4 x 1-1/2"
- (53703212)
(17) WL5 - Wafer Lag
1/4 x 2-1/2"
- (52613222)
(4) WL3 - Wafer Lag
1/4 x 1-3/8"
- (52613216)
(5) LS9 - Lag Screw
5/16 x 4-3/4"
- (52213343)
(5) WB9 -
Wafe
r
Bolt 5/16 x 2-1/8"
- (53613324)
(7) WB8 -
Wafer Bolt 5/16 x 2-3/8"
- (53613326)
(7) WB7 -
Wafer Bolt 5/16 x 3"
- (53613330)
(4) G21 -
Hex Bolt 5/16 x 3-3/4"
- (53703333)
(12) G13 -
Hex Bolt 5/16 x 6-1/8"
- (53703364)
(7) WB10 -
Wafer Bolt 5/16 x 2-5/8"
- (53613330)
(1) G26 -
Hex Bolt 3/8 x 9-1/4"
- (53703891)
(4) G17 -
Hex Bolt 3/8 x 6"
- (53703860)
(1) G20 -
Hex Bolt 3/8 x 4"
- (53703840)
(1) H8 -
Hex Bolt 1/4 x 4-1/4"
- (53703241)
Hardware Identification
(53" Add On A)
(Actual Size)

11
(47) S3 - Wood Screw
#8 x 2-1/2"
- (52043522)
(21) S4 - Wood Screw
#8 x 3"
- (52043530)
(28) S7 - Pan Screw
#12 x 2"
- (52433620)
(17) S6 - Pan Screw
#12 x 1"
- (52433610)
(21) S10 - Pan Screw
#8 x 1"
- (52433510)
(28) S33 - Wood Screw
#8 x 1"
- (52043510)
(215) S20 - Wood Screw
#8 x 1-3/8"
- (52043516)
(10) S0 - Truss Screw
#8 x 7/8" - (52933505)
(1) LW2 - 5/16" Lock Washer - (51303300)
(18) LN2 - 5/16" Lock Nut
-
(54303300)
(26) TN2 - 5/16" T- Nut
-
(54503300)
(9) BN1 - 1/4" Barrel Nut
-
(54803200)
(5) TN1 - 1/4" T - Nut
-
(54503200)
(14) LW1 - 1/4" Lock Washer - (51303200)
(70) FW2 - 5/16" Flat Washer - (51103300)
(11) FW1 - 1/4" Flat Washer - (51103200)
(9) FW0 - 3/16" Flat Washer - (51103100)
(52) S8 - Pan Screw
#12 x 3/4"
- (52433603)
(12) S18 - Wood Screw
#6 x 1"
- (52013910)
(10) PB2 - Pan Bolt
1/4 x 1-1/4"
- (53433212)
(12) FW10 - 3/8" Flat Washer - (51103800)
(33) S13 - Pan Screw
#6 x 5/8" - (52413908)
(6) LN3 -
3/8 Lock Nut
- (54303800)
(8) FW6 - #8 Screw Bezel
-
(9299500)
(89) LN1 -
1/4 Lock Nut
- (54303200)
(89) PB1 - Pan Bolt
1/4 x 3/4"
- (53453203)
(1) PB6 - Pan Bolt
1/4 x 1"
- (53413210)
(76) S11 - Wood Screw
#8 x 2"
- (52043520)
Hardware Identification
(53" Add On A)
(Actual Size)

12
(1) 051 - 1-1/4 x 43 x 92"
Front Wall Panel
37598971
(1) 052 - 1-1/4 x 43 x 92"
Back Wall Panel
37598970
(2) 204 - 1-1/4 x 2 x 27-1/2" - Crowsnest Spacer - 3599043
(1) 023 - 1 x 4 x 21" - Ladder Gap - 3598958
(1) 192 - 5/4 x 4 x 34" - Crowsnest Back - 3599036
(1) 220 - 1 x 6 x 29-3/8" - Crowsnest Gap Board - 3599040
(2) 221 - 1 x 6 x 29-3/8" - Crowsnest Floor - 3599038
(1) 280 - 1-1/4 x 3 x 32-1/4" - TNR Ground Brace - 3598963
(10) 070 - 1 x 5 x 35-5/8" - Floor Board - 3599051
(1) 031 - 1 x 5 x 22-1/8" - Access Board - 3599032
(1) 010 - 2-13/32 x 6-3/4 x 34 "
Folding Bench 37592658
(1) 133 - 1 x 2 x 27-7/16" - Chalkwall Side - 3599035
(1) 025 - 1 x 4 x 41-3/4" - RW - AL Support - 3599062
(1) 041 - 1-1/4 x 21-1/2 x 92"
Narrow Back Panel
37598992
(1) 042 - 1-1/4 x 21-1/2 x 92"
Narrow Front Panel
37599003
(1) 120 - 1-1/4 x 15-3/4 x 42-1/8"
Door Window Panel
37608977
Part Identification (53" Add On B) (Reduced Size)

13
(2) 190 - 2 x 6 x 15" Crowsnest Gusset - 3598112
(2) 211 - 2 x 4 x 12-1/2" - Short Crowsnest Joist
- 3599063
(1) 121 - 5/4 x 3 x 10" - Door Stop - 3592715
(5) 033 - 1 x 6 x 22-1/8" - Board Rock B - 3598512
(4) 032 - 1 x 6 x 22-1/8" - Board Rock A - 3598511
(4) 363 - 1 x 5 x 10" - Sunburst Side - 3599066
(1) 091 - 1-1/4 x 3 x 22" - Diagonal - 3592607
(2) 212 - 3/4 x 3-1/4 x 14-3/4" - Crowsnest Side - 3599042
(1) 361 - 1 x 6 x 19" - Bk Centre Gable - 3599033
Part Identification (53" Add On B) (Reduced Size)

14
(2) 393 - 1 x 5 x 12-1/8" - End Gable B
- 3599046
(2) 394 - 1 x 5 x 7-1/8" - End Gable C
- 3599047
(1) 203 - 5/4 x 4 x 25-1/2" - Crowsnest Short
- 3598115
(4) 022 - 5/4 x 4 x 19-1/2" - Tread - 3598957
(2) 391 - 1 x 5 x 17-1/8" - End Gable A - 3599045
(1) - 390 - 1 x 6 x 34-15/16" - Fr Centre Gable - 3599052
(2) 191 - 2 x 4 x 13-1/2" - Crowsnest Joist
- 3599041
(1) 132 - 1-1/4 x 5 x 10" - Chalkwall Block
- 3599034
(1) 141 - 4 x 4 x 16" - SW Mount - 3599069
(2) 062 - 1-1/4 x 3 x 72" - Roof Support - 3599060
(2) 210 - 3/4 x 5-1/4 x 14-3/4" - Crowsnest Bottom Side
- 3599037
(2) 392 - 1 x 5 x 17-1/8" - End Gable D
- 3599048
(2) 201 - 1 x 2 x 34-1/8" - Upright Crowsnest - 3599072
(4) 340 - 1-1/4 x 3 x 50-15/16" - Roof Rafter - 3599059
(1) 370 - 1-1/4 x 3 x 34-1/2" - Mid Gable Support
- 3599057
(3) 070 - 1 x 5 x 35-5/8" - Floor Board - 3599051
(1) 030 - 1 x 6 x 22-1/8" - Access Rock Bottom
- 3598515
(1) 090 - 5/4 x 4 x 14¼ - SW Ground
- 3592606
(1) 151 - 2-1/2 x 3 x 15" - Block SW - 3598507
(1) 200 - 2 x 4 x 29-1/2" - Crowsnest Top - 3599044
(2) 362 - 5/4 x 6 x 12" - Starburst Centre
- 3598305
(1) 360 - 1-1/4 x 3 x 34-1/2" - Back Gable Support
- 3599031
(1) 081 - 5/4 x 3 x 33" - Half Wall Top - 3599053
(1) 080 - 5/4 x 3 x 33-1/2" - SW Wall Top - 3599071
(1) 131 - 5/4 x 5 x 39-5/8" - Table Top - 3592611
(1) 072 - 1 x 4 x 35-5/8" - Floor Board - 3599050
(4) 230 - 1 x 4 x 29" - Cedar Wall - 3591975
(1) 100 - 5/4 x 4 x 27-3/4" - RW-AL Ground Brace
- 3599061
(1) 202 - 2 x 4 x 29-1/2" - Crowsnest Front - 3599039
(2) 060 - 1-1/4 x 3 x 40-3/4" - Floor Joist - 3592608
(1) 071 - 1-1/4 x 3 x 63-1/4" - Long Floor Joist - 3599056
(1) 150 - 2-1/2 x 3 x 15" - SW Block Angle - 3599068
(1) 281 - 1-1/4 x 3 x 20-1/4" - TNR Upright - 3598965
Not Used
Part Identification (53" Add On C) (Reduced Size)

15
(1) 050 - 1-1/4 x 37 x 92"
SW Wall Panel
37599007
(1) 350 - 1-1/4 x 39 x 50-3/16"
Roof Panel A - 37599022
(1) 351 - 1-1/4 x 39 x 50-7/16"
Roof Panel B - 37599029
(1) 040 - 1-1/4 x 37 x 92"
Slide End Panel
37598981
Part Identification (53" Add On C) (Reduced Size)

16
1x - Rocks (9pk)
(3320093)
Green/Yellow/Burgundy
1x - Telescope w/ Mount
(3320161)
2x - Swing Belt Seat
(9320130) Green
1x - Steering Wheel
(3320255)
2x
- Flower Box
(9320401) Green
1x - Plastic Formed
Washer (18 Pk)
(3290000)
2x - Acro Handle
(9320131) Green
1x
- Gable Clock Assembly
(3320164) Green
2x
- 2 x 2 Panel Window
(9320118) -Green
1x
- Sky Chalk
Wall (3320117)
1x - TNR 2 Slide Lt Flange
(3310222) Yellow
1x
- TNR 2 Slide Rt Flange
(3310223) Yellow
9x - TNR 2 Slide Elbow
(3310221) Yellow
10x - TNR 2 Clamp Ring
(9300220) (Yellow)
10pcs number 3300220
1x
- TNR 2 Slide Exit Top
(3310224) Yellow
1x - TNR3 Short Exit
(3310232) Yellow
1x - Maze N Wave 2.35m Slide
(3318215) Yellow
Part Identification
(53" Add On D)
(Reduced Part Size)
Part Identification
(53" Add On E)
(Reduced Part Size)

17
1x - Rocks (9pk)
(3320093)
Green/Yellow/Burgundy
1x - Telescope w/ Mount
(3320161)
2x - Swing Belt Seat
(9320130) Green
1x - Steering Wheel
(3320255)
2x
- Flower Box
(9320401) Green
1x - Plastic Formed
Washer (18 Pk)
(3290000)
2x - Acro Handle
(9320131) Green
1x
- Gable Clock Assembly
(3320164) Green
2x
- 2 x 2 Panel Window
(9320118) -Green
1x
- Sky Chalk
Wall (3320117)
(4) 230 - 1 x 4 x 29" - Cedar Wall - 3591975
(1) 460 - 1-1/4 x 2-1/4 x 25-1/2" - Wall Board Support
- 3592915
(16) S20 - Wood Screw
#8 x 1-3/8"
- (52043516)
(3) S3 - Wood Screw
#8 x 2-1/2"
- (52043522)
(1) 470 - Upper Window Insert
1.27 x 18.8 x 35.86 - 37592655
(9) S0 - Truss Screw
#8 x 7/8" - (52933505)
Part Identification
(53" Add On F)
(Reduced Part Size)
Hardware Identification (53" Add On F) (Actual Size)
Hardware Identification
(53" Add On G)
(Actual Size)
Part Identification
(53" Add On G)
(Reduced Part Size)

18
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 4)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 5)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 6)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 1)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 2)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 3)
MODEL NUMBER: Brockwell / Preston / Twin Mountain Lodge
TRACKING NUMBER (from ID Plaque):
B. If there are any missing or damaged pieces or you need assistance with
assembly please contact the consumer relations department directly. Call us
before going back to the store.
Key Number: The rst two digits represent the step
number. The third digit represents the piece. Note
that if the part is used in multiple steps then the
number only reects the rst step it is used in.
Quantity Key Number Part Description,
Part Size
2X 012 Post 2 x 4 x 83”
Step 1: Inventory Parts - Read This Before Starting Assembly
C. Read the assembly manual completely, paying special attention to ANSI warnings;
notes; and safety/maintenance information on pages 1 - 6.
D. Before you discard your cartons ll out the form below.
• The carton I.D. stamp is located on the end of each carton. The tracking number is
located on the KK ID Plaque (9320374).
• Please retain this information for future reference. You will need this information if you
contact the Consumer Relations Department.
• Please refer to Page 6 for proper hardware assembly.
• Each step indicates which bolts and/or screws you will need for assembly, as well as
any at washers, lock washers, t-nuts or lock nuts.
A. This is the time for you to inventory all your hardware, wood and accessories,
referencing the parts identication sheets. This will assist you with your assembly.
• The wood pieces will have the key number stamped on the ends of the boards.
Organize the wood pieces by step, as per the key numbering system below.
[phone]
[email protected]
For online parts replacement visit
https://parts.kidkraft.eu/
1.800.933.0771 or 972.385.0100
[email protected]
[email protected]
For online parts replacement visit
https://parts.kidkraft.com/

19
Fig. 1.1
Hardware
Step 1: Bench Assembly
A: Open the Folding Bench Assembly. (g. 1.1, 1.2 and 1.3)
B: Make sure assembly is level then secure with 2 (H1) 1/4 x 1-1/2” Hex Bolts (with lock washer, at washer and
t-nut) per side. (g. 1.4)
C: Tighten the top screws in all 4 Bench Legs. (g. 1.4)
4 x 1/4 x 1-1/2” Hex Bolt
 (1/4”lockwasher,1/4”atwasher,1/4”t-nut)
H1
Wood Parts
1 x Folding Bench 2-13/32 x 6-3/4 x 34”
1/4” lock
washer
1/4” at
washer
1/4” t-nut
Tighten these
screws - all 4 legs
Bench Legs
H1
Fig. 1.2
Fig. 1.3
Bench Legs
Fig. 1.4
010
010

20
1 x Left Access 1-3/8 x 2-1/2 x 57-7/8”
1 x Right Access 1-3/8 x 2-1/2 x 57-7/8”
4 x Tread 5/4 x 4 x 19-1/2”
022
021
020
Fig. 2.1
Wood Parts Hardware
Step 2: Access Ladder / Rockwall Assembly
Part 1
A: Place (020) Left Access on one side of 4 (022) Treads and (021) Right Access on the other side with the
grooves facing in. (g. 2.1)
B: Fit each (022) Tread into grooves on both (020) and (021) Access rails, make sure the top edge of the (022)
Treads are ush to the front of the Access rails. (g. 2.1 and 2.2)
C: Pre-drill pilot holes with a 1/8” drill bit and attach rails and treads together using 4 (S3) #8 x 2-1/2” Wood
Screws per tread. (g. 2.1)
16 x #8 x 2-1/2” Wood Screw
S3
Fig. 2.2
020
021
022
End View
Flush to
edges Top Edge of Access Rail
Flush to
top edge
022
S3
S3