KIDSMILL Up! Newborn set User manual

Newborn Set - User manual AUS
Manual - Kidsmill Up! - Newborn set E3 AUS.indd 1 31-8-2018 15:54:38

2
INDEX
Congratulations
Warnings/Safety measures/Maintenance
Parts
Installation
Use
Adjustment
Warranty
3
3
4
5
6
6
7
IMPORTANT! RETAIN THESE INSTRUCTIONS FOR
FUTURE REFERENCE AND READ CAREFULLY
Manual - Kidsmill Up! - Newborn set E3 AUS.indd 2 31-8-2018 15:54:38

3
CONGRATULATIONS
Congratulations on the purchase of this Kidsmill Up! Newborn set. This product
meets the most stringent safety requirements and is approved according to the
Australian Standard AS 4684:2009 . Using this Newborn set can only be safe when
used according to these instructions. Please read this instruction manual carefully
and store it for future reference. The safety of your child may be aected if these
instructions are not followed.
WARNINGS
WARNING – Follow the manufacturer's instructions.
WARNING – Do not leave your child unattended.
WARNING – The harness must always be used and correctly tted - most injuries
from high chairs are caused by falls.
WARNING – Position the high chair away from solid structures and benches to avoid
injuries caused by falls and by acces to dangerous items.
• Never leave your child unattended.
• Make sure that the harness is tted correctly.
• Do not use the newborn set once your child can sit unaided.
• This newborn set is not intended for prolonged periods of sleeping.
• It is dangerous to use this product on an elevated surface, e.g. a table.
• Always use the restraint system.
• Do not use this product unless all components are correctly tted and adjusted.
• Be aware of the risk of open re and other sources of strong heat, such as electric
bar res, gas res, etc. in the near vicinity of this product.
SAFETY MEASURES
• This newborn set is intended for children weighing up to 9 kg.
• Always use the safety harness.
• This product does not replace a cot or a bed. Should your child need to sleep,
then it should be placed in a suitable cot or bed.
• Do not use the newborn set if any components are broken, torn or missing.
• Do not use accessories or replacement parts other than those approved by the
manufacturer.
• Do not move the newborn set when your child is still in it.
MAINTENANCE
• We recommend cleaning this newborn set using a damp cloth.
• Never use aggressive or abrasive cleaning agents because these can aect this
product and can also be detrimental to the health of your child.
• Ensure all locking devices work correctly and check the locks and ttings
regularly.
KIDSMILL NEWBORN SET UP!
Manual - Kidsmill Up! - Newborn set E3 AUS.indd 3 31-8-2018 15:54:39

4
12. Frame (1x)
9. Mounting bracket (1x)
11. Rod (1x)
10. Mounting bracket (1x)
PARTS
Reuse ttings from
high chair
1. Screw M6x45 (2x)
2. Nut M6 (2x)
3. Screw M4x16 (4x)
4. Extender (2x)
5. Screw 4,5x35 (4x)
6. Screw M6x85 (2x)
7. Hex Key 4 (1x)
8. Clip (2x)
Important! Insert the thin end of the
nut rst.
6
ONDERDELEN/PARTS/TEILE
1. Schroef M6x45 (2x)
1. Screw M6x45 (2x)
1. Schraube M6x45 (2x)
2. Moer M6 (2x)
2. Nut M6 (2x)
2. Nuss M6 (2x)
Onderdelen uit kinderstoel
Fittings from high chair
Teile von Hochstuhl
5. Schroef M6x85(2x)
5. Screw M6x85(2x)
5. Schraube M6x85(2x)
4. Schroef M6x12(4x)
4. Screw M6x12(4x)
4. Schraube M6x12(4x)
3. Extender (2x)
3. Extender (2x)
3. Extender (2x)
6. Clip (2x)
6. Clip (2x)
6. Clip (2x)
7. Schroef M4x16(4x)
7. Screw M4x16(4x)
7. Schraube M4x16(4x)
12. Frame (1x)
12. Frame (1x)
12. Rahmen(1x)
9. Bevestigingsbeugel (1x)
9. Mounting bracket (1x)
9. Befestigingsbügel (1x)
11. Spanstang (1x)
11. Rod (1x)
11. Metallstange (1x)
10. Bevestigingsbeugel(1x)
10. Mounting bracket (1x)
10. Befestigingsbügel (1x)
8. Inbussleutel 4 (1x)
8. Hex Key 4 (1x)
8. Sechskantschlüssel 4(1x)
Belangrijk! Plaats de dunne zijde van
de moer eerst in het gat.
Important! Insert the thin end of the
Wichtig! Legen Sie die dünne Seite der
1.
4.
3.
6.
7.
8.
4. 5.
Tools needed
Manual - Kidsmill Up! - Newborn set E3 AUS.indd 4 31-8-2018 15:54:46

5
INSTALLATION
Step 1: Remove the back, safety bar, seat
and Glider Boots of the Kidsmill Up! high
chair.
Beware! Keep the parts for later use.
Step 2: Screw(3) the extenders(4) under the
front legs of the chair.
4x
Step 3: Fasten the steel tension rod(11) and
the mounting brackets(9 + 10) between the
legs of the chair.
7
MONTAGE/INSTALLATION/MONTAGE
Stap 1: Verwijder de rugleuning, beugel en
zitting van de Kidsmill Up! kinderstoel.
Let op! Bewaar de onderdelen voor later
gebruik.
Step 1: Remove the back, safety bar and
seat of the Kidsmill Up! high chair. Beware!
Keep the parts for later use.
Schritt 1: Entfernen Sie die Rückseite,
Sicherheitsbügel und den Sitz des Kidsmill
Up! Stuhl. Vorsicht! Bewahren Sie die
Unterteilen für die spätere Verwendung.
Stap 2: Schroef(4) de extenders(3) vast
onder de achterpoten van de kinderstoel.
Step 2: Screw(4) the extenders(3) under the
rear legs of the chair.
Schritt 2: Schraube(4) Sie die Extendern(3)
unter die hintere Beine des Hochstuhls.
Let op! Gebruik schroevenset 4,5x35 (art. 75100766) in geval van:
Een stoel uit de series: 701389 t/m736894
Beware! Use screw set 4,5x35 (art. 75100766)in case of:
Achair from the series: 701389 to 736894
Vorsicht! Verwenden Sie Schraube 4,5x35 (art. 75100766) im Fall von:
Ein Stuhl aus der Serie: 701389 bis 736894
4x
2x
2x
Stap 3: Bevestig de metalen spanstang(11)
en de bevestigingsbeugels(9+10) tussen de
poten van de kinderstoel.
Step 3: Fasten the steel tension rod(11) and
the mounting brackets(9 + 10) between the
legs of the chair.
Schritt 3: Befestigen Sie die
Stahlspannstange(11) und die Befestigungs-
bügel(9 + 10) zwischen den Stuhlbeine.
2.
1.
5.
2x
2x
4x
7
MONTAGE/INSTALLATION/MONTAGE
Stap 1: Verwijder de rugleuning, beugel en
zitting van de Kidsmill Up! kinderstoel.
Let op! Bewaar de onderdelen voor later
gebruik.
Step 1: Remove the back, safety bar and
seat of the Kidsmill Up! high chair. Beware!
Keep the parts for later use.
Schritt 1: Entfernen Sie die Rückseite,
Sicherheitsbügel und den Sitz des Kidsmill
Up! Stuhl. Vorsicht! Bewahren Sie die
Unterteilen für die spätere Verwendung.
Stap 2: Schroef(4) de extenders(3) vast
onder de achterpoten van de kinderstoel.
Step 2: Screw(4) the extenders(3) under the
rear legs of the chair.
Schritt 2: Schraube(4) Sie die Extendern(3)
unter die hintere Beine des Hochstuhls.
Let op! Gebruik schroevenset 4,5x35 (art. 75100766) in geval van:
Een stoel uit de series: 701389 t/m736894
Beware! Use screw set 4,5x35 (art. 75100766)in case of:
Achair from the series: 701389 to 736894
Vorsicht! Verwenden Sie Schraube 4,5x35 (art. 75100766) im Fall von:
Ein Stuhl aus der Serie: 701389 bis 736894
4x
2x
2x
Stap 3: Bevestig de metalen spanstang(11)
en de bevestigingsbeugels(9+10) tussen de
poten van de kinderstoel.
Step 3: Fasten the steel tension rod(11) and
the mounting brackets(9 + 10) between the
legs of the chair.
Schritt 3: Befestigen Sie die
Stahlspannstange(11) und die Befestigungs-
bügel(9 + 10) zwischen den Stuhlbeine.
2.
1.
5.
2x
2x
4x
Manual - Kidsmill Up! - Newborn set E3 AUS.indd 5 31-8-2018 15:54:47

6
8
MONTAGE/INSTALLATION/MONTAGE
Stap 5: Bevestig de bekleding aan het
frame(12) met de drukknopen.
Step 5: Attach the fabric to the frame(12)
with the press-studs.
Schritt 5: Befestigen Sie die Bekleidung zu
dem Rahmen(12) mit den Druckknöpfen .
Stap 4: Schroef(7) de clips(6) vast op het
frame(12).
Step 4: Screw(7) the clips(6) onto the
frame(12).
Schritt 4: Schraube(7) Sie die Clips(6) auf
dem Rahmen(12).
Stap 1: Schuif het zitje door todat het is
vergrendeld met een duidelijk hoorbare
"Klik" aan de beide zijdes.
Step 1: Push the seat until it locks with an
clear audible "Click" on both sides.
Schritt 1: Schieben Sie den Sitz, bis er
blokiert mit einem hörbaren "Klick" auf
beiden Seiten.
'CLICK'
'CLICK'
GEBRUIK/USE/GEBRAUCH
4x
INSTALLATION
Step 5: Attach the fabric to the frame(12)
with the press-studs.
Step 4: Screw(5) the clips(8) onto the
frame(12).
Step 1: Push the seat until it locks with an
clear audible "Click" on both sides.
'CLICK'
'CLICK'
USE
Manual - Kidsmill Up! - Newborn set E3 AUS.indd 6 31-8-2018 15:54:51

7
ADJUSTMENT
Step 2: To unlock the seat, pull up both
buttons, at the sides of the seat, at the same
time and slide the seat o the high chair.
Step 2: Use the buckle slider to set the
desired length, adapted to your child.
Step 1: Press button A to unlock the harness.
To lock the harness slide Part B onto Part
C before clicking them together into the
buckle.
A.
B.
C.
Manual - Kidsmill Up! - Newborn set E3 AUS.indd 7 31-8-2018 15:55:02

8
WARRANTY
Validity: 2 years from date of purchase.
The warranty is only valid in conjunction with proof of purchase. The warranty
covers the replacement of the entire product or parts when there a manufacturing
defect. After the expiration of the warranty there are costs attached to any repairs.
The supplier takes no responsibility for any damage or injury to persons, animals and
belongings due to misuse of the harness or by failure to follow the accompanying
instructions.
Exclusion
All rights in respect of the guarantee and the responsibility of the supplier shall lapse
if the product:
• Is dismantled by unauthorized persons;
• Is not properly used or stored.
Furthermore, all external damage to the product that does not aect the proper
functioning is excluded from the warranty.
Manual - Kidsmill Up! - Newborn set E3 AUS.indd 8 31-8-2018 15:55:02

9
Notes: ....................................................................................................................................................
.................................................................................................................................................................
.................................................................................................................................................................
.................................................................................................................................................................
WARRANTY FORM
Customer name: ........................................................................................................................................................
Order number: ............................................................................................................................................................
Quantity Damaged Missing
...................
...................
...................
...................
...................
...................
...................
...................
................... ...................
................... ...................
Product:
Article number:
Serial number:
..................................................................
...................................................................
...............................................................
Part number (p. 4)
EN - In case of damaged or missing parts, please ll in this form and send
to the following E-mail address: Anstel Nominees Pty Ltd
Service department
i[email protected]
Manual - Kidsmill Up! - Newborn set E3 AUS.indd 9 31-8-2018 15:55:02

10
The information contained herein is subject to change without notice. Timgro BV shall not be
liable for technical errors or omissions contained herein. The purchased product may dier from
the product as described in this user guide.
Anstel Nominees Pty Ltd
36 Sunline Drive
Truganina VIC 3029
Australia
e-mail: [email protected]
Version: August 2018
Manual - Kidsmill Up! - Newborn set E3 AUS.indd 10 31-8-2018 15:55:02