kim lighting HA31 User manual

HA31 - Ribbon Arm Wall Mount with Top Scroll Installation Instructions
P.O. Box 60080 • 16555 East Gale Ave.
City of Industry, California 91716-0080
626/968-5666 •FAX [phone]
Revision 7/16/10 EC 100715008 Status 3 Part No. 95712
Tools Required:Flat Head ScrewdriverTorque WrenchF" Hex Wrench
3/32" HexWrench5/32" Hex WrenchSealant
RA17, AE17, BE17, LE19:N" 6- or 12- Point Deep (2" min.) Socket12" (min.) Long Socket Extension
RA25, AE21, BE21, LE26:L" 6- or 12- Point Deep (2" min.) Socket20" (min.) Long Socket Extension
WARNING: Fixtures must be grounded in accordance with local codes or the National Electrical Code.
Failure to do so may result in serious personal injury.
MAINTENANCE: A regularly scheduled maintenance program must be established to insure paint coating is
intact, corrosion or structural damage has not occurred, and all mounting arms, rods, nuts and bolts are tight.
Failure to do so could lead to danger or serious personal injury.
CAUTION: Structural integrity of mounting plate attachment to wall is by others.
KEEP THIS SHEET FOR FUTURE REFERENCE.
Make certain electrical supply is OFF before starting installation.
1. Remove wiring inspection cover
from wall plate and wall mount
cover plate. Adhere rope caulk in a
continuous strip into the wall plate
groove. Allow caulk to extend well
above the wall plate surface to
ensure a proper seal.
2. Securely mount wall plate over
junction box (by others).
CAUTION: Structural integrity
of mounting plate attachment to
wall is by others.
!
4. Attach fixture to arm fitter. (See
fixture installation instructions.)
3. Insert arm bolts into wall mount
cover.
Junction Box
(By Others)
Wall Mount
Cover
Arm Fitter
Wall Plate
Groove
5. Install ribbon arm onto wall plate
cover.
Ribbon
Arm
6. Pull fixture wires through arm fitter,
ribbon arm and wall plate cover.
Install arm fitter with fixture head to
ribbon arm using a torque wrench.
Fixture Wires
!
RA17, AE17, BE17, LE19
RA25, AE21, BE21, LE26

Page 2 Kim Lighting • 16555 E. Gale Ave. • P.O. Box 60080 • City of Industry, CA 91716-0080 • 626/968-5666 • FAX [phone]
HA31 - Ribbon Arm Wall Mount with Top Scroll Installation Instructions
KIM LIGHTING LIMITED WARRANTY
When installed in accordance with Kim Installation Instructions and
accepted trade practices, the following shall apply:
General Product Limited Warranty Coverage
All material and component parts used in the manufacture of Kim
Products, are warranted to be free from defects of material and/or
workmanship for a period of 1 year from date of sale, with the following
exceptions:
Auxiliary Equipment
All auxiliary equipment (such as lamps, ballasts, and transformers)
provided by and/or included in Kim Products shall carry the component
manufacturer's warranty.
Copper and Bronze Landscape Components
Copper and Bronze Landscape fixture components shall be warranted
against defects of material and/or workmanship, and failure due to
corrosion, for a period of 25 years from date of sale.
Composite In-Grade Components
Composite In-Grade fixture components installed below grade, shall be
warranted against defects of material and/or workmanship, and failure
due to corrosion, for a period of 7 years from date of sale.
Aluminum Landscape Components
Aluminum Landscape fixture components not in direct contact with soil,
shall be warranted against defects of material and/or workmanship for a
period of 3 year from date of sale. Aluminum fixture components in
direct contact with soil shall be warranted from defects of material and
failure from corrosion for a period of 1 year from date of sale.
Limit of Liability and General Conditions
Only products which are installed, used and maintained in accordance
with applicable Kim instructions, specifications and accepted trade
practices, are covered by the Kim Warranty. During the warranty
period, with proof of purchase, Kim will repair or replace with the same
or similar product, at Kim's option, without charge. Labor costs are the
owner's responsibility and are excluded from this warranty. This
warranty is void if the product is modified, tampered with, misapplied,
poorly installed, improperly maintained, or subjected to abnormal
conditions.
Repair or replacement as provided under this warranty is the exclusive
remedy of the purchaser. This warranty is in lieu of all other warranties,
expressed or implied, including any implied warranty of fitness for a
particular application. Kim Lighting shall not be liable to the purchaser
for indirect or consequential damages.
9. Attach arm fitter cover.
How may we serve you better?
Please let us know. Visit our website at:
www.kimlighting.com
Your concerns are important to us.
7. Attach top scroll to ribbon arm and wall
plate cover.
8. Attach wall plate cover assembly to wall
plate. Secure using two (2) socket head
cap screws. Connect fixture wires to
supply wires observing polarity, i.e.; green-
to-ground, white-to-common, and black-to-
voltage.
10. Attach splice cover using the 10-32 flat
head stainless steel socket screw.
Socket
Head Cap
Screws (2)
Wall Plate
Cover
Assembly
Splice Cover Screw