Kimex 013-5002 User manual

INSTALLATION MANUAL
Corner Wall Mount
013-5002
55"
MAX
200x200/300x300
400x200/400x400
ISSUED: NOV. 2015
4. Adjustment
Adjust to the desired position or tilt.
Maintenance
• Check that the bracket is secure and safe to use at regular intervals(at least every three months).
• Please contact your dealer if you have any questions.
7
+15°
-15°
45kg
(99lbs)
RATED
45kg
(99lbs)
RATED
+5°
-5°
CAU T ION: DO NOT EXCEED
RATED LISTED WEIGHT. SERIOUS
INJURY OR PROPERTY DAMAGE
MAY OCCUR!

21
Component Checklist
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation.
If any parts are missing or faulty, telephone your local distributor for a replacement.
Package W
ST6.3x55 (x )
W-A
6 concrete anchor
W-B
(x6) D6 washer (x6)
W-C
adapter bracket (x2)
B
articulated arm assembly (x1)
A
Package M
M5x14
M-A
(x4) M6x14
M-B
(x4)
washer
M-F
(x4)
M8x20
M-C
(x4)
big spacer
M-H
(x4)
M6x30
M-D
(x4)
M8x30
M-E
(x4) small spacer
M-G
(x8)
NOTE: Read the entire instruction manual before you start installation and assembly.
WARNING
• Do not begin the installation until you have read and understood all the instructions
and warnings contained in this installation sheet. If you have any questions
regarding any of the instructions or warnings, please contact your local distributor.
• This mounting bracket was designed to be installed and utilised ONLY as
specified in this manual. Improper installation of this product may cause damage
or serious injury.
• This product should only be installed by someone with good mechanical ability
who has basic building experience and fully understands this manual.
• Make sure that the supporting surface will safely support the combined weight of
the equipment and all attached hardware and components.
• Always use an assistant or mechanical lifting equipment to safely lift and position
the equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can cause damage
to the items, This greatly reduces their holding power.
• This product is intended for indoor use only. Using this product outdoors could
lead to product failure and personal injury.

X X
√
4
3
Installers must verify that the supporting surface will safely support the combined weight of
the equipment and all attached hardware and components.
WARNING
1. For Solid Brick and Concrete Mounting
Screw the wall
mount onto
the wall
60mm
(2.4")
60mm
(2.4")
ø 10mm
(ø 3/8")
Drill pilot holes
1
2
Mark the
exact location of
mounting holes
2. Installing the Adapter Brackets
2-1 For Flat Back Screens
TV
TV
TV
Top of the display
M-A
M-B
M-C
M-F
W-B
W-A
W-C

65
2-2 For Recessed Back Screens or to Access A/V Inputs
or or or
M-C M-C
M-D
M-E
M-F
M-G
M-F
M-G
M-D
M-E
M-F
M-H
M-D
M-E
M-F
M-H
M-G
M-G
TV
TV
TV
Tighten all screws but do not over tighten.
· Position the adapter brackets as close as possible to the center of the display.
· Screw the adapter brackets onto the display.
Note: Choose the appropriate screws, washers and spacers (if necessary) according to the type of screen.
3. Hooking the Display onto the Wall Mount
Tighten the two bolts by using a proper phillips screwdriver to secure the bracket.
safety bolt
wall
wall