kincrome K13263 User manual
INDUSTRIAL 1/2” DRILL REVERSIBLE INDUSTRIAL 1/2” DRILL REVERSIBLE
INDUSTRIAL
1/2” DRILL
REVERSIBLE
K13263
ED1 December 15
COMPACT
AND
LIGHT
WEIGHT
ROTATING
SIDE
HANDLE
LOW
NOISE
KEYLESS
CHUCK
2
YEAR
WARRANTY
1
INDUSTRIAL 1/2” DRILL REVERSIBLE
Table of Contents
Know Your Product ...................................................................................................1
General Safety Instructions .....................................................................................2
Additional Safety Instructions..................................................................................3
Assembly...................................................................................................................4
Operation...................................................................................................................4-5
Maintenance & Warranty .........................................................................................5
Parts Breakdown......................................................................................................6
Know your product
Model No:................................................................................................................... K13263
Description: .............................................................................................................. Industrial 1/2” Drill Reversible
Air Inlet: .................................................................................................................... 1/4”
Average Air Consumption:....................................................................................... 113LPM (4CFM)
Chuck Size: ................................................................................................................ 1/2” (13mm)
Free Speed: ............................................................................................................... 450 RPM
Air Pressure (max.): ................................................................................................ 90PSI
Hose Length (max.): ................................................................................................. 10 Meters
Hose Diameter (min.):.............................................................................................. 10mm
Weight: ....................................................................................................................... 1.5kg
1
2
1. Air Inlet
2. Exhaust
3. Forward/Reverse Switch
4. Trigger
5. Side Handle
6. Keyless Chuck
7. Rotating Handle Assembley
8. 3mm Hex
9. Nitto Style Fitting
3
4
5
6
8
7
9
2
INDUSTRIAL 1/2” DRILL REVERSIBLE INDUSTRIAL 1/2” DRILL REVERSIBLE
General Safety Warnings
Save all warnings and instructions for future reference.
WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may
result in electric shock, fire and/or serious injury.
1) Work Area
a. Keep the work area clean and well lit. Cluttered benches and dark areas increase the risks of electric shock, fire, and
injury to persons.
b. Keep bystanders, children, and visitors away while operating the tool. Distractions can result in the loss of control of
the tool.
c. Keep children and bystanders away while operating any powered products. Distractions can cause you to lose control.
2) Personal Safety
a. Stay alert. Watch what you are doing and use common sense when operating the tool. Do not use the tool while tired or
under the influence of drugs, alcohol, or medication. A moment of inattention while operating the tool increases the risk of
injury to persons.
b. Dress properly. Do not wear loose clothing or jewellery. Contain long hair. Keep hair, clothing, and gloves away from
moving parts. Loose clothes, jewellery, or long hair increases the risk of injury to persons as a result of being caught in
moving parts.
c. Avoid unintentional starting. Be sure the switch is off before connecting to the air supply. Do not carry the tool with your
finger on the trigger or connect the tool to the air supply with the trigger on.
d. Remove adjusting keys and wrenches before turning the tool on. A wrench or a key that is left attached to a rotating part of
the tool increases the risk of personal injury.
e. Do not overreach. Keep proper footing and balance at all times.Proper footing and balance enables better control of the tool
in unexpected situations.
f. Use safety equipment. A dust mask, non-skid safety shoes and a hard hat must be used for the applicable conditions. Wear
heavy-duty work gloves during use.
g. Always wear eye protection. Wear approved safety eye protection.
h. Always wear hearing protection when using the tool. Prolonged exposure to high intensity noise can contribute to
hearing loss.
3) Tool Use and Care
a. Use clamps or other practical ways to secure and support the workpiece to a stable platform. Holding the work by hand or
against the body is unstable and can lead to loss of control.
b. Do not force the tool. Use the correct tool for the application. The correct tool will do the job better and safer at the rate for
which the tool is designed.
c. Do not use the tool if the trigger does not turn the tool on or off. Any tool that cannot be controlled with the trigger is
dangerous and must be repaired, by an authorised repair agent.
d. Disconnect the tool from the air source before making any adjustments, changing accessories, or storing the tool. Such
preventive safety measures reduce the risk of starting the tool unintentionally. Turn off and detach the air supply, safely
discharge any residual air pressure, and release the throttle and/or turn the switch to its off position before leaving the
work area.
e. Store the tool when it is idle out of reach of children and other untrained persons. A tool is dangerous in the hands of
untrained users.
f. Maintain the tool with care. A properly maintained tool is easier to control.
g. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that affects the tool’s
operation. If damaged, have the tool serviced before using, at an authoriesd Kincrome repair agent.Many accidents are
caused by poorly maintained tools.
h. Use only accessories that are identified by the manufacturer for the specific tool model. Use of an accessory not intended
for use with the specific tool model, increases the risk of injury to persons.
3
INDUSTRIAL 1/2” DRILL REVERSIBLE
4) Service
a. Tool service must be performed only by qualified repair personnel.
b. When servicing a tool, use only identical replacement parts. Use only authorized parts.
c. Use only the lubricants specified by the manufacturer.
5) Additional Safety Warnings
a. The warnings and precautions discussed in this manual cannot cover all possible conditions and situations that may
occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this
product, but must be supplied by the operator.
b. Only use with accessories rated to handle the forces exerted by this tool during operation. Other accessories not
designed for the forces generated may break and forcefully launch pieces.
c. Attach all accessories properly to the tool before connecting the air supply. A loose accessory may detach or
break during operation.
d. Thoroughly read and understand the manual for the air compressor used to power this tool.
e. Use this tool with both hands only. Using tools with only one hand can result in loss of control.
f. Do not lay the tool down until it has come to a complete stop. Moving parts can grab the surface and pull the tool out of your
control.
g. Do not force the tool. Use a larger one if needed.
h. Anyone using vibrating tools regularly, or for an extended period should first be examined by a doctor and then have
regular medical check-ups to ensure medical problems are not being caused or worsened from use. Pregnant women
or people who have impaired blood circulation to the hand, past hand injuries, nervous system disorders, diabetes, or
Raynaud’s Disease should not use this tool. If you feel any symptoms related to vibration (such as tingling, numbness, and
white or blue fingers), immediantly discontinue use and seek medical advice as soon as possible.
i. Do not smoke during use. Nicotine reduces the blood supply to the hands and fingers, increasing the risk of vibration-related injury.
j. Wear suitable gloves to reduce the vibration effects on the user.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities,
contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and cement or other masonry products
• Arsenic and chromium from chemically treated lumber
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure
to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust
masks that are specially designed to filter out microscopic particles.
6) Description of Symbols
The following symbols could be shown on the tool:
Read the instruction manual before use.
Risk of Explosion
Wear Ear Protection
Wear Eye Protection
noNo-load speed, Free Speed CFM Cubic Feet per Minute flow
.../min, RPM Revolutions or reciprocation per minute SCFM Cubic Feet per Minute flow at
standard conditions
PSI Pounds per square inch of pressure NPT National pipe thread, tapered
Nm Newton meters of force BSP British standard pipe
4
INDUSTRIAL 1/2” DRILL REVERSIBLE INDUSTRIAL 1/2” DRILL REVERSIBLE
7) Assembly
Installing the rotating handle
1. Screw in the side handle (5) clockwise to securly fasten it into the rotating handle asembly (7).
2. Once desired position has been found, use the 3mm hex key (8), and tighten the hex bolt located on the rotating handle
assembley (7), to lock the handle into position.
Reversible Drill User Instructions
8) Before Starting
TO PREVENT SERIOUS INJURY FROM EXPLOSION:
1. Verify compressor is off before setup. Use only
clean, dry, regulated, compressed air to power this tool. Do
not use oxygen, carbon dioxide, combustible gases, or any
other bottled gas as a power source for this tool.
2. It is recommended a filter, regulator with pressure gauge, oiler,
in-line shut-off valve, and quick coupler be fitted for optimal
operation, as shown on Figure A.
3. An in-line shut-off ball valve is an important safety device,
it will shut-off the air supply even if the air hose is ruptured.
The shut-off valve should be a ball valve because it can be
closed quickly.
Note: If an automatic oiler system is not used, add a 4 to 5 drops of
Kincrome Air Tool Oil to the air inlet before operation. Add a 1-2 more
drops every hour of continual use.
4. Attach an air hose to the compressor’s air outlet. Connect the air hose to the air inlet (1) of the tool. Other components, such as
a quick connect fitting and quick connect coupler, will make operation more efficient, but are not required.
WARNING! Do not install a quick coupler directly on the tool. Couplers contains an air valve that will allow the air tool
to retain pressure and inadvertently operate after the air supply is disconnected.
5. The air hose must be long enough to reach the work area and allow free movement while working.
6. Turn on the air compressor according to the manufacturer’s directions and allow the tank to build up pressure until it cuts-off.
7. Adjust the air compressor’s regulator so that the air output is at the tools recommended working pressure, the output must not
exceed the tool’s maximum air pressure at any time. Adjust the pressure gradually, while checking the air output gauge to set
the optimal pressure range.
8. Inspect all air connections for leaks. Repair any leaks.
9. If the tool is not be used, turn off and detach the air supply, safely discharge any residual air pressure, and release the trigger (4)
and/or turn the tools switch to its off position to prevent inadvertent operation.
9) Operation
1. Screw in Nitto Style Fitting (9) to the air inlet (1). Thread (teflon) tape may be required to ensure a leak free seal
2. Connect the air hose to the air inlet (1) of the tool.
Changing the rotation direction
1. The direction of the bit rotation is reversible.
2. Control the rotation direction by moving the side-mounted forward/reverse switch (3) as required for the operation. Connect the
air hose to the air inlet (1) of the tool.
Figure A
5
INDUSTRIAL 1/2” DRILL REVERSIBLE
Installing and removing the drill bits
WARNING! Disconnect tool from air supply before servicing or changing accessories.
To Install drill bits:
1. Remove the air supply from the reversible drill.
2. Insert the drill bit as far as possible into the the keyless chuck (6).
3. Once the drill bit has been placed inside the keyless chuck (6), turn the keyless chuck (6) clockwise to fasten your drill bit
secureley.
To remove the drill bits:
1. Remove the air supply from the reversible drill.
2. Grab the keyless chuck (6) firmly and turn anti-clockwise to loosen the drill bit out of the keyless chuck (6).
3. Remove the drill bit.
10) Cleaning, Maintenance, and Lubrication
Note: These procedures are in addition to the regular checks and maintenance explained as part of the regular operation of the
air-operated tool.
The air motor and bearing uses compressed air to power the tool. Moisture in compressed air will rust the motor components, you
must lubricate the motor daily with Kincrome air tool oil.
Lubrication
1. Disconnect the tool from the air supply holding it so the air inlet (1) faces up.
2. Hold the trigger (4) down and put 4 to 5 drops of Kincrome air tool oil in the air inlet (1). Holding the trigger down helps circulate
oil in the motor.
3. Connect the tool to air supply, cover the exhaust (2) with a towel and run for a few seconds.
WARNING! Any excess oil in the motor is immediately expelled from the exhaust (2). Always direct the exhaust (2) away
from people or objects.
Storage
1. Avoid storing the tool in a location subject to high humidity. If the tool is left as it is used, the residual moisture inside the tool
can cause rust. Before storing and after operation, oil the tool and run it for a short time.
2. Regular inspection should be carried out of the keyless chuck (6) and accessories for wear.
11) Warranty
Warranty given by Kincrome Australia Pty Ltd of 3 Lakeview Drive, Caribbean Park, Scoresby, Victoria (Tel 1300 657 528). The applicable
warranty period (24 months) commences on the date that the product is purchased. If this product has materials or workmanship defects
(other than defects caused by abnormal or non warranted use) you can, at your cost, send the product to place of purchase, an autho-
rised Kincrome service agent or one of Kincromes addresses for repair or replacement. Your rights under this warranty are in addion to
any other rights you have under the Australian Consumer Law or other applicable laws. Our goods come with guarantees that cannot be
excluded under the Australian Consumer Law. You are entled to a replacement or refund for a major failure and compensaon for any
other reasonably foreseeable loss or damage. You are also entled to have the goods repaired or replaced if the goods fail to be of ac-
ceptable quality and the failure does not amount to a major failure. For further details please visit www.kincrome.com.au or call us. Due
to minor changes in design or manufacture, the product you purchase may somemes dier from the one shown on the packaging.
IMPORTANT! If the tool fails to operate correctly, call customer service on 1800 657 528 for advice on the best resoluon for your situa-
on. If a resoluon cannot be achieved over the phone please take the tool and all related accessories to an authorised service centre or
place of purchase showing proof of purchase for assistance.
6
INDUSTRIAL 1/2” DRILL REVERSIBLE INDUSTRIAL 1/2” DRILL REVERSIBLE
12) Parts Breakdown
NO PART NO DESCRIPTION
Q'TY NO PART NO DESCRIPTION Q'TY
01 K13263-1 HOUSING 125 *K13263-25 ROTOR BLADE 4
02 K13263-2 PIN(2.5*24) 126 K13263-26 FRONT PLATE 1
03 K13263-3 WASHER 127 K13263-27 BEARING 1
04 K13263-4 VALVE 128 K13263-28 WASHER 1
05 K13263-5 SPRING 129 K13263-29 GEAR LINK 1
06 K13263-6 EXHAUST SLEEVE 130 K13263-30 GEAR LINK 1
07 K13263-7 O-RING (S12.5) 131 K13263-31 GEAR 6
08 K13263-8 AIR INLET 133 K13263-33 PIN 6
09 K13263-9 WASHER 134 K13263-34 GEAR PLATE 2
10 K13263-10 SILENCER 135 K13263-35 GEAR SHAFT 1
11 *K13263-11 TRIGGER 136 K13263-36 SHAFT 1
12 *K13263-12 REVERSE LEVER 137 K13263-37 BEARING (6200ZZ) 2
13 *K13263-13 O-RING 1 38 K13263-38 WASHER 1
14 K13263-14 O-RING (17*1) 139 K13263-39 CLAMP NUT 1
15 K13263-15 BUSHING 140 *K13263-40 HANDLE LINK 1
16 K13263-16 O-RING 1 41 *K13263-41 HANDGRIP 1
17 K13263-17 O-RING 1 42 *K13263-42 SCREW (M4*16) 1
18 K13263-18 VALVE STEM 143 *K13263-43 NUT 1
19 K13263-19 PACKING 144 *K13263-44 WASHER 1
20 K13263-20 BEARING 145 *K13263-45 1/2" KEYLESS CHUCK 1
21 K13263-21 REAR PLATE 146 *K13263-46 CHUCK SCREW 1
22 K13263-22 PIN(2.5*6) 247 K13263-47 HEX (3mm) 1
23 K13263-23 CYLINDER 148 *K13263-48 SPRING 1
24 K13263-24 ROTOR 1
WE RESERVE THE RIGHT TO CHANGE PARTS WITHOUT NOTICE K13263 V1
K13263 1/2" DRILL
* Indicates Stocked Spare Parts
www.kincrome.com.au
Table of contents
