King 4WD 17050101 RTG User manual

Revised 9.3.19
Installation Instructions:
(Part # 17050101 RTG)
2007-2018 Jeep JK Heavy Duty Tire Carrier Kit
NOTE: Carefully read entire instructions thoroughly before attempting to install this part.
Parts Included Qty
HD Tire Carrier 1
Tire Mount Bracket Base 1
Tire Mount Bracket 1
Tire Gate Mount 1
Wheel Mount Stud: 1/2”-20 3
Lug Nuts: 1/2”-20 3
Hardware Pack: Wheel Mount 1
10mm-1.0 X 30mm Hex Head Bolt Gr. 8.8 5
10mm Nylock Nut 5
10mm Flat Washer 10
Parts Included Qty
12mm-1.75.X 35-40mm Hex Head Bolt Gr. 8.8 4
12mm– 1.75 Nylock Nut 4
12mm Flat Washer 4
6mm-1.0 X 20mm Hex Head Bolt Gr. 8.8 4
6mm– 1.0 Nylock Nut 4
6mm Flat Washer 8
8mm-1.25 X 40mm Hex Head Bolt Gr. 10.9 8
8mm Flat Washer 8
8mm Lock Washer 8
Third Brake Light Lower Bracket 1
Third Brake Light Upper Bracket 1
INSTALLATION:
Step 1: Place the vehicle on a flat, level surface and engage the parking brake.
Step 2: Remove the spare tire and unbolt and remove the OE rear tire mount from the rear
gate. Remove the OE third brake light assembly according to manufacturer’s specifications.
Step 3: Carefully, remove the upper and lower OE plastic rear gate hinge covers. (Fig. A)

Revised 9.3.19
Installation Instructions:
(Part # 17050101 RTG)
2007-2018 Jeep JK Heavy Duty Tire Carrier Kit
Step 4: Using masking tape, secure the rear gate in place. Unbolt the (10) OE bolts securing
the upper and lower OE hinges to the rear gate. Save the OE hardware for reinstallation.
(Fig. B)
NOTE: Place a block of wood between the bumper and the tailgate, placing slight pressure
on both. This will prevent tailgate misalignment when OE hardware is removed.
Fi
g
. A
Plastic Hinge
Cover
OE Hinge
Rear Gate
Rear Gate
OE Hinge
Bolts
Rear Gate
Rear Gate
Fig
. B
OE Hinge
Bolts

Revised 9.3.19
Installation Instructions:
(Part # 17050101 RTG)
2007-2018 Jeep JK Heavy Duty Tire Carrier Kit
Step 5: Lift the HD tire carrier into place and secure to OE hinge points using the previously
removed (4) OE bolts. Tighten the (4) OE hinge bolts. Make sure all remaining HD tire
carrier mounting holes line up with existing holes in the rear gate before tightening the OE
bolts. (Fig. C)
NOTE: If the tailgate moved, realign as necessary. Starting a few bolts in the
remaining mounting holes will help to ensure the mounting holes are properly aligned.
Step 6: Torque the OE hinge bolts, starting with the outside bolts first, according to
manufacturers specifications. Carefully, open the rear gate and torque the inner hinge bolts
according to manufacturer’s.
NOTE: It is recommended to apply medium strength (blue) threadlocker to the OE hinge
bolts.

Revised 9.3.19
Installation Instructions:
(Part # 17050101 RTG)
2007-2018 Jeep JK Heavy Duty Tire Carrier Kit
Fig. D
RTG Tire
Carrier
OE
Bolts
RTG Tire
Carrier
Fig. C

Revised 9.3.19
Installation Instructions:
(Part # 17050101 RTG)
2007-2018 Jeep JK Heavy Duty Tire Carrier Kit
Step 7: Press the wheel mount studs, in your desired pattern, into the tire mount bracket base .
(Fig. E)
NOTE: The studs may be pressed into place. DO NOT use lug nuts to install the studs.
Step 8: Assemble the wheel mount bracket (tire mount bracket & tire mount bracket
base) using the supplied (5) 10mm X 30mm bolts and hardware. Leave the bolts loose at this
time. Lay the spare tire face down on the ground and install the wheel mount bracket
temporarily onto the spare tire. (Fig. F)
Step 9: With the spare tire face down, lay a ruler or a flat bar across the tire and adjust the
wheel mount bracket assembly until the base makes contact with the ruler or flat bar. Torque
the wheel mount bracket assembly bolts to ?? ft./lbs. (Fig. F)
NOTE: The assembled bracket may not line up perfectly with the straight edge.
Fig. E
Wheel
Mount
Studs
Tire
Mount
Bracket

Revised 9.3.19
Installation Instructions:
(Part # 17050101 RTG)
2007-2018 Jeep JK Heavy Duty Tire Carrier Kit
Step 10: Secure the tire mount bracket assembly (outside) and the 3rd brake light lower
bracket (inside) to the tire carrier mount using the (4) supplied 12mmX 35mm bolts and
hardware. Torque 12mm hardware to 80 ft./lbs. (Fig. G)
NOTE: The size of the spare tire will determine the mounting height of the bracket. If
possible, it is better to have the tire fit tighter against the straight edge/tire gate to avoid
excess vibration.
TIP: For off-road applications, raise the tire position for more departure angle. For
street driven applications, lower the tire position for greater rear window vision.

Revised 9.3.19
Installation Instructions:
(Part # 17050101 RTG)
2007-2018 Jeep JK Heavy Duty Tire Carrier Kit
Step 11: Secure the tire carrier mount assembly to the rear gate mounting holes and HD tire
carrier using the (8) supplied 8mm X 40mm bolts and washers. Torque the 8mm hardware to
factory ft./lbs. (Fig. H)
Step 12: Install the spare tire to the tire mount bracket and secure using the supplied lug nuts.
Tire Carrier
Mount
Tire
Mount
Bracket Base
12
mm X
35
mm Bolts
Fig. G
Fig. H
Tire Carrier
Mount Assembly
8
mm X
40
mm
Bolts
RTG Tire
Carrier

Revised 9.3.19
Installation Instructions:
(Part # 17050101 RTG)
2007-2018 Jeep JK Heavy Duty Tire Carrier Kit
Step 13: If a third brake light is being used, install the third brake light upper bracket onto the
third brake light lower bracket and secure using the (4) supplied 6mm X 20mm bolts and
hardware. (Fig. I)
IMPORTANT!: Be sure third brake light is mounted so it will be visible above the spare
tire.
Step 14: Remove the (2) OE screws from the OE plastic third brake light assembly. Install the
OE front plastic panel and lens into the new third brake light assembly using the (2) previously
removed OE screws. (Fig. I)
Step 15: Depending on the mounting position of the third brake light assembly the wiring
harness may need to be extended. Extend the third brake light wiring harness to the
passenger side hinge, then up the tire gate. This can simply be done by splicing the wire and
using some insulated butt splice connectors and 18 gauge wire, extend the wire to the
appropriate length. It is recommended to have this done by an experienced electrical installer.
IMPORTANT!: Make sure there is enough slack in the wire throughout the
tailgate travel.
Fig. I
OE Plastic Third
Brake Light
Assembly
Third Brake
Light Lower
Bracket
Third Brake
Light Upper
Bracket
6
mm X
20
mm
Bolts

Revised 9.3.19
Installation Instructions:
(Part # 17050101 RTG)
2007-2018 Jeep JK Heavy Duty Tire Carrier Kit
Step 16: Adjust the HD tire gate assembly for level and re-torque mounting hardware as
necessary.
Step 17: Installation is now complete. (Fig. J)
Step 18: Periodically check and re-torque mounting hardware. Especially after off-road use.
Product cleaning and maintenance instructions
Fig. J
Finished Installation

Revised 9.3.19
Installation Instructions:
(Part # 17050101 RTG)
2007-2018 Jeep JK Heavy Duty Tire Carrier Kit
Stainless Steel Finish – Aluminum polish may be used to polish small scratches and scuffs on the finish.
Mild soap, window or glass cleaner may be used to clean the finish. Dual state powder coat finish –
Mild soap, window or glass cleaner may be used to clean the finish. In order to protect the finish, you
may wax your product on a regular basis with pure carnauba automotive wax. Do not use any types of
soap, polish or was that contains abrasive that could damage the finish. Textured coated finishes should
be cleaned with a mild soap on a damp sponge. Do not apply polish or was that requires to be removed
by means of buffing. This type of wax is commonly used at car wash facilities. Chrome Finish – Mild
soap, window or glass cleaner may be used to clean the finish. In order to protect the finish you should
wax your product on a regular basis with pure carnauba automotive wax. Do not use any types of soap,
polish or was that contains abrasive that could damage the finish.
Limited Warranties
King 4WD’s products are covered under the following limited warranties only. Note that the
duration of the limited warranty differs according to the material and finish of the product
purchased. Subject to the duration and conditions of the limited warranty stated below, King
4WD’s warrants to the original retail purchaser that its products are free from defects in material
and workmanship. All other warranties and representations express or implied, are hereby
disclaimed, including fitness for merchantability and buyer’s intended use or purpose. All parts
are sold “AS IS” except for the limited warranties granted herein. Buyer assumes all risks as to
the selection, suitability and performance of all goods and products selected. This limited
warranty does not cover damage or impairment in any part due to misuse, improper installation,
accident or contact with on-road or off-road hazards, product modification, improper or
inadequate cleaning and/or maintenance. King 4WD’s is not responsible for items damaged
during shipping. This warranty is not transferable from the original buyer. For the original
Buyer to be eligible for the limited warranty coverage, the Buyer must provide proof of
purchase. King 4WD’s strongly recommends returning the warranty registration card.
Customer’s remedy hereunder shall be limited only to repair or replacement (at King 4WD’s
option) of any defective part(s) returned to King 4WD’s at customer’s expense. The
determination of whether or not a returned part is defective or subject to coverage under the
limited warranties stated herein shall be made at King 4WD’s sole discretion.
To assure product quality, King 4WD’s reserves the right to change product design, material,
specification and finishes without prior notice to customers. This limited warranty gives you
specific legal rights and you may also have other rights, which may vary from state to state.
Some states do not allow limitations on how long an implied warranty lasts, so the above

Revised 9.3.19
Installation Instructions:
(Part # 17050101 RTG)
2007-2018 Jeep JK Heavy Duty Tire Carrier Kit
limitations may not apply as to you. Also, some states do not allow the exclusion or limitation
of incidental or consequential damages, so the above limitations or exclusions may not apply to
you. King 4WD’s reserves the right to discontinue product lines and substitute products, or
provide other remedies than those listed in this limited warranty for those discontinued products.
Warning
Rollover and other types of vehicle accidents may result in serious injury or death to you, your
passengers and others sharing the road. King 4WD’s accessories are decorative and are not
intended to reduce or avoid injury or damage in the event of an accident. The weight and
location of King 4WD’s accessories may affect your vehicles’ handling, stability and
performance, creating an increased risk of accident or rollover. Before installing any accessory,
check state laws and assure that the accessory will not obscure any lights or interfere with proper
operation on your vehicle’s safety equipment. Consult your owner’s manual and the King
4WD’s instructions, or additional safety information. King 4WD’s products, nor the warnings
contained herein, are not a substitute for your safe driving. Don’t drink and drive, always use
seat belts and don’t drive faster than conditions permit.