Kingyoo PE84W14B-C User manual

PE84W14B-C
Before operating the unit, please read this
manual thoroughly and retain it for future
reference
Depending on PC graphic card, touch response time
can be lagged while using it under UHD resolution
(3,840x2,160).
It is strongly recommended to set the resolution to
1,920x1,080 for the touch function.

2
Contents
1) Safety Warning.....................................................................................3P
2) Installation............................................................................................4P
3) Motion Control Switch ..........................................................................4P
4) Input Signal Terminal ........................................................................6-7P
5) Remote Control Guide.......................................................................8-9P
6) AV Equipment Connection and Setting .........................................10-13P
7) OSD Menu .........................................................................................14P
8) Troubleshooting .................................................................................25P
9) Maintenance.......................................................................................26P
10) PC Input Supported Signal..........................................................27-28P
11) USB Media Player Support Specification..........................................29P

3
1) Safety Warning
Placement
Do not place the unit on an unstable cart, stand, tripod, bracket, table, or shelf or any place with uneven
ground.
Do not expose the unit to direct sunlight and other sources of heat.
Do not put the unit near appliances that create magnetic fields.
Do not install in the place with high moisture.
Do not handle liquids near or on the unit.
Do not overload any articles or goods randomly in to the unit.
Do not put heavy object on top of the unit.
Power
Check if the unit’s operating voltage is conformed to your local power supply.
Disconnect power cord and antenna plug from the wall socket when under thunder-storm or lightning
weathers.
Disconnect power cord and antenna plug from the wall socket if there is nobody at home or didn’t use over
a long period of time.
Please keep power cord from physical or mechanical damage.
Please use exclusive power cord, don't modify or lengthen it.
Please check and ensure AC source is connected with the ground.
Screen
Never use any other tough or sharp object to replace the written pen.
Unplug the power supply plug before cleaning.
Clean the screen with a soft dustless and dry cloth.
Never use water or the spray type detergent to clean the unit.
For deep clean, contact an authorized service center.
Please don't display the high brightness image on the screen for a long time.
Sight Distance
The best distance between audience and screen is 5-7 times that of screen diagonal.
The best watching angle between audience and screen as top and bottom, or so inside 176 degrees.
Temperature
Do not place the unit near or over a radiator or heater register.
If your unit is suddenly moved from a cold to a warm place, unplug the power cord for at least, two hours so
that moisture that may have formed inside the unit can dry completely.
Optimal operation temperature is 5~40 degrees.
Humidity
Do not expose machine in rain, damp or place near water.
Ensure the indoor drying, cool.
Ventilation
Keep the ventilation openings clear.
Ensure that the unit has enough space for ventilation around: left, right and back >10cm, top> 10cm.
Standby mode
Press the standby button on the side of the product for sleep mode unless power is not completely turned
off.
Battery
Accurate transaction and recall scrap battery after using; correctly handle and collect the battery.
For the safety issue, do not place the battery where children can easily reach, and do not dispose
batteries in fire.
Wall bracket
Wall bracket : Building in type

4
2) Installation
Unpacking
Accessories
User Manual, Remote Controller, Battery, Power Cord, HDMI Cable, USB Cable,(Option)
User Manual Batteries
Power Cord Touch USB Cable HDMI Cable Remote Control
(Option)
●Actual accessories may seem different then this manual
●Accessories may changed or added without notice due to quality assurance of the product

5
3) Motion Control Switch
Switch Control Panel
Article
Function Description
①
Power switch
② INPUT
Input Signal Menu
③ MENU
Select the OSD Menu
④ SEL UP
Move upward in OSD Menu
⑤ SEL DOWN
Move downward in OSD Menu
⑥ VOL UP
Move left in OSD Menu/ Volume Up
⑦ VOL DOWN
Move right in OSD Menu/ Volume Down
⑧Power indicator
Check the power source
⑨Remote control
signal receiver
Location of the remote control’s signal reception

6
4) Input Signal Terminal
Input Signal Terminal (Side)
Article
Function Description
①USB IN
USB 2.0 Movie / Upgrade Monitor Main Board
②HDMI 1 IN
Connect to UHD Multimedia Interface (HDMI1.4)
③HDMI 2 IN
Connect to UHD Multimedia Interface (HDMI1.4)
④HDMI 3 IN
Connect to UHD Multimedia Interface (HDMI1.4)
⑤DP IN
Connect to UHD Multimedia Interface (Displayport)
⑥TOUCH IN
(OPTION)
Connect Jaguar Board and PC using USB Cable. While
installing the touch driver, this product will be able to
controller external PC through touch.
(Touch Solution is available only when it is connected to
VGA, DVI, HDMI, DP mode.)

7
Input/Output Signal Terminal (Back)
Article
Function Description
①DVI IN
External PC Input
DVI OUT
Connect to other display device with DVI Input
VGA IN
External PC video input
PC Sound IN
External PC audio input
SPDIF OUT
Connect to external speakers with AMP-use digital audio Output
Component IN
Connect to Set-top box or DVD or YPbPr signal device
AV IN
Audio / Video Input
LineOUT
Connect to external speakers with AMP audio Output
RS232
A serial interface used for data transmission
RS485
A serial interface used for data transmission
AC IN
AC power input

8
5) Remote Control Guide
1. Open the battery compartment cover on the back of the remote control.
2. Insert battery into the battery compartment following the indications (+,-) inside the compartment.
3. Close the compartment cover once completed.
<Caution>
Safely dispose dead batteries.
Remote control
reception range

9
Key Name
Operation
►Power ON / OFF
INPUT
►Input source selection/Activate OSD Menu
VIDEO
►Switch to VIDEO/COMPONENT mode
PC
►Switch to PC/DVI mode
DP
►Switch to DP mode
HDMI
►Switch to HDMI 1 / HDMI 2 / HDMI3 mode
MENU
►Select OSD Menu
EXIT
►Exit OSD Menu
▲
►Move upward on OSD Menu
▼
►Move downward on OSD Menu
▶
►Move to right on OSD Menu
◀
►Move to left on OSD Menu
OK
►Move to OSD Menu
Auto Sleep
►Select auto-sleep when there is no signal (ON / OFF)
INFO
►Display signal information
+ VOL -
►Volume up/down
MUTE
►Mute mode
▼ PAGE ▼
►Move to file list page of USB
USB
►Move to USB mode
█
►Stop playback content
▶
►Play playback content
││
►Pause playback content
◀◀
►Rewind the video content
▶▶
►Fast forward the video content
│◀
►Move to previous video content mode
▶│
►Move to next video content mode

10
For the security reason, do not connect to power plug while installing external device.
6) AV Equipment Connection and Setting
1. Computer Touch Connection & Monitor Input Signal (DP, HDMI, DVI, RGB)
▶Touch function option
I. Connect the DP or HDMI cable to port terminal.
II. Connect the USB cable to USB port.
III. Connect the Power cord.
IV. Reboot external computer. (Need to install touch driver software to activate touch functions)
V. Press the to turn on the power.
NOTE: 1920*1080 is the optimum resolution connecting to the external computer.
The external computer can be connected through HDMI Cable.
▶Preferred PC Specification
∙CPU : Intel i5 4th generation or better
∙RAM : DDR3 16 GB (PC3-12800) or better
∙VGA card : Radeon R9 270X OC D5 or better
∙SSD / HDD : over 120 GB / over 1T
∙POWER : over 800W

11
DP Connection
I. Connect through a DP terminal with external devices such as PC, DVD Player and AV equipment to
Connect the DP cable to DP port.
II. Connect the Power cord.
III. Press the to turn on the power.
IV. Press the INPUT button to switch to DP port.
3. HDMI1 / HDMI2 / HDMI3
I. Connect through a HDMI terminal with external devices such as PC, DVD player, set-top box and AV
equipment to display UHD quality resolution. (3x HDMI port)
II. Connect the HDMI cable to HDMI port.
III. Connect the power cord.
IV. Press the to turn on the power.
V. Press the INPUT button to switch to HDMI port.

12
4. SPDIF Connection
I. Connect SPDIF optical cable to SPDIF output terminal.
II. Connect the power cord.
III. Press the to turn on the power.
IV. Press the INPUT button to switch to the SPDIF port.
5. DVI Input/output
I. Connect DV cable with each DVI-IN, DVI-OUT and connect Phone jack speaker cable with AUDIO-OUT
II. Connect power cord
III. Turn the device on by pressing button
IV. Press INPUT button to switch DVI mode
▶Supports DVI output function
SPDIF Fiber Cable
Sound Equipment

13
6. Component (Y / Pb / Pr)
I. Connect component cable to the component port.
II. Connect the power cord.
III. Press the to turn on the power.
IV. Press the INPUT button to switch to the component port.
Camcorde
r
Game Console
Set-top box
Video Player
Satellite TV
Receiver

14
7) OSD Menu
1. INPUT SOURCE
Adjust input source of the monitor.
Press “SOURCE” to display a list of the input source.
Select desired input using by pressing ▼/▲ buttons.
Press the ENTER key to select the input source.
To exit, press “EXIT” button.

15
2. Picture Menu
Press ▼/▲ to select one of the options below.
Press “ENTER” to enter sub-menu for to adjust it.
Picture Mode User mode[User/Sports/Standard /Comfort mode]
By default Video mode is set to User, but it can be manually adjusted.
Color Temperature [Standard /Warm/User/Cool]
Use ◀/ ▶button to adjust the color temperature.
Aspect Ratio Size [Auto/4:3/16:9/Zoom1/Zoom/Original Screen(UHD resolution excluded)]
While connecting to external devices, please use this function to adjust the screen size.
You can select the screen size.
Noise Reduction [Off/Low/Medium/High/Standard(UHD resolution excluded)]
You can select the noise reduction
Energy Saving : Brightness can be adjusted up 57% for energy-saving purpose.
Color Range: Specifies a color range.

16
3. Sound Menu
Sound Mode User [Standard /Music/Cinema/Sports/User]
Balance: Adjust level of volume of both speakers.
Auto Volume: Set automatically the same volume level between the channel and program.
Surround Sound: Set the surrounding sound.
SPDIF MODE: AUTO/PCM
EQ: Set voice frequency band which are divided into five levels.

17
4. Time Menu
Press "MENU" button then press ◀/▶to select time menu.
Clock: Not supported.
Off Time: Not supported.
On Time: Not supported.
Sleep Time: Sleep Time: Select the time in minute auto power off time. Press “OFF”to cancel the operation.
.
Auto Power Saving: Off:To cancel Auto power saving which is designated to turn off the screen after 5 minutes of
inactivity.
On: To activate Auto power saving which is designated to turn off the screen after 5 minutes of
inactivity.

18
5. Option Menu
Press "MENU" button then press ◀/▶to select time menu.
OSD Language: Set OSD menu language.
OSD Transparency: Low /Medium /High /Off (UHD resolution excluded)
Software update (USB): Download Bin extension file to download for update.
OsdDuration: Set the On Screen Display (OSD) remaining time.

19
6. Media Menu
The upper left corner icons notify whether the device has detected an USB memory or not.
For further details, see below
For Photo, please refer to p.20
For Music, please refer to p.21
For Movie, please refer to p.22-23
For Text, please refer to p.24

20
●Photo
Pleas choose the picture to display and press “Enter”to select. Once selection one picture, you will be able to
display all pictures in the same folder.
Press to play or stop.
Press to view the previous picture.
Press to view the next picture.
Press to stop and return to user interface.
Press to select the repeat mode Repeat One/All/None/Random.
Press to play or stop the background music.
Press to view the list of pictures.
Press to view the information (Resolution / Size / Date / Time).
Press to rotate clockwise.
Press to rotate counterclockwise.
Press to Zoom in.
Press to Zoom Out.
After zoom in a picture, select the icon then press “ENTER”press ↓/↑& ←/→to view the picture.
Play mode Normal/Random/Blocks/Diagonal../Wipe/Slide/Fade.