kinpus KP-CK63307I User manual

IR DOME PAN TILT
USER’S MANUAL

Respect for the users：
Thank you for our products. This product adopts
the company of innovation in the design, PAN-TILT
structure optimization, and do a lot of testing on
a long time, the adjustment to ensure that the product
of the superior quality. All our efforts were in order
to make our products more stable performance, and can
adapt to the majority of customers' requirements. You
can make a better use of equipment, please read this
manual, if any problem, please inform us or dealers.
Thanks again!
1
Ｐｌｅａｓｅ ｂｅ ｓｕｒｅ ｔｏ ｓｅｌｅｃｔｅｄ ｉｎｆｒａｒｅｄ ｃａｍｅｒａ ｉｎｄｕｃｔｉｏｎ
Ｐｌｅａｓｅ ｆｏｌｌｏｗ ｔｈｅ ｉｎｓｔｒｕｃｔｉｏｎｓ ｓｔｒｉｃｔｌｙ

10、Specification
DC-485R HDD SYSTEM TIANDI DVR
PHILIPS DVR JC-4116 HDD SYSTEM
SAMSUNG DVR TC-Pelco D HDD SYSTEM
RD140（RM110） DVR TC-Pelco P HDD SYSTEM
2 11
MODEL KP-CK63307I KP-CK63309I
Pan-tilt 7inch 9inch
IR LED
24 850nm LED,
effective distance
80m
24 850nm LED,
effective distance
120m
IR LED Input Voltage DC12V 1.5A
Pan-tilt Input Voltage 24V AC 50/60Hz
Pan-tilt Input Power 10W
Can output Voltage DC12V/500mA
Lens driving voltage DC12V/100mA
Angle level：0°--355° vertical：0°--90°
Speed level：10°/S vertical：5°/S
limit level adjustment
Communication Bus RS485
Baud Rate 1200/2400/4800/9600 BPS
Dimension 150×65×70 mm
（V×T×H）
200×75×70 mm
（V×T×H）
Temperature -25℃--49℃
materials CoverFlame-retardant ABS or aluminum
optical transparent cover: Acrylic
Weight 3.0Kg 3.5Kg
1、 ……………………………………………………3
2、Attentions …………………………………………………3
3、Use and defend maintenance points for attention…3
4、Fundamental structure of pan-tilt……………………5
5、Product external form dimension………………………5
6、 ……………………………………………………6
7、The Built-in Decoder ……………………………………8
8、Bps and address Set ……………………………………...... 9
9、Auto recognition agreements list……………………10
10、 ……………………………………………11
CONTENTS
Assembly
Specification
Feature

30 0011110 40 0101000 50 0110010 60 0111100
31 0011111 41 0101001 51 0110011 … ………
32 0100000 42 0101010 52 0110100 … ………
33 0100001 43 0101011 53 0110101 127 1111111
34 0100010 44 0101100 54 0110110 note：1=ON，0=OFF
explain：DIP switch to digital is "OFF"，The corresponding number is
0，Dial “ON”，The corresponding number is 1。
7 DIP switch is address code switch, adopt binary coding, can setting 128
different address code, 9 is low, 3 is high, encode according from low to high
Address calculation method:( Below is the switch “ON” the state of the value in)
switch：3 4 5 6 7 8 9
value：64 32 16 8 4 2 1
1, select the mann yards agreement, the address code number starting from 0,
the maximum set to 128, which corresponds to the matrix decoder addresses
the camera 1 to 0; when the system is used in more than 64 decoder should
use the code distributor to achieve expansion.
2, Shanghai Chenova system for all agreements and KODICOM system
KRE-301 protocol address encoded as 16 hex mode, the system address is
"10", the actual address of the corresponding decoder 16.
3, part of the system, PELCO P / HY protocol address is 1, the software is set to
1, corresponding to the address decoder is set to 2.
9、Auto recognition agreements list：
agreements name Adaptive System agreements name Adaptive System
Pelco D DVR ST-832 HDD SYSTEM
Pelco P DVR Pelco D WX HDD SYSTEM
CS850 DVR HIKVISION DVR
1、Feature
Special Designed Camera, IR LED Partition Ray System, Without
Glisten Phenomenon.
Used the powerful IR LED from Taiwan, Qualified Disperse Heat
solution to avoid part warm up.
Constant power supply to ensure the IR LED for long time working.
IR LED Board has the Windy Circle system; Once the LED on, it
works.
When long distance watching, the IR field can be adjusted.
Powerful power supply, stable electricity and pressure suitable for
long time working.
Double Anti-sunshine structure, weatherproof for out door/ In door
using.
Acrylics Optics Housing, No distortion.
2、Attentions：
☆ Don't be installed in the indoor of the equipment exposed to rain or
moisture
☆ Don't be put inside the device objects, which could cause a
short-circuit and damaged equipment or system；
☆ Avoid installation in flammable and explosive gas or corrosive gas
exists；
☆ Don't remove pan-tilt internal components and parts and repair itself；
☆ Don't exceed the environment temperature, humidity standards；
☆ AC24V power supply for pan-tilt, DC12V power supply for infrared
lamp, Please confirm by strict specifications, higher than the voltage
access the voltage specification access will cause equipment burn。
3
10

3、Use and defend maintenance points for attention：
☆In the repair, replacement or cleaning the product, please cut off power
supply。
☆Supporting power source elicitation line if necessaries lengthen, general
the length can not exceed 10 meters , The line footpath can not be lower
than 0.5 mm directly 2。
☆When cleaning, please do not use this product type or spray liquid
cleaner, otherwise it will cause short-circuit internal line。
☆Camera equipment installation, please promptly after fixed camera lens
video, and power lines, to prevent pan-tilt rotating process and equipment
damage cable pan-tilt。
☆When installation, please pay attention to protect transparent cover
carelessly, such as dirty, with a soft cloth and neuter cleaner cleanness
☆Installs when the camera and the transparent cover please defer to the
arrow to show the direction installment
☆Installed outside, please support joints and screw in waterproof, prevent
water treatment equipment, damage to the equipment into the indoor
⑤JP5：Dial DIP switch to digital is "OFF"，The corresponding number
is 0，Dial“ON”，The corresponding number is 1。Article 1-2 says bps
and special agreement, Article 3-9 says decoder board address.
8、Bps and address Set：
1. Special agreements and communication bps Set（Auto identification
of initial state of agreement，2400bps，as000）
DIP1-2 BPS agreement note
00 2400
01 4800
10 9600
Auto
recognition
agreements
Auto identification in more
than 20 agreement, auto
recognition agreements list
explain：DIP switch to digital is "OFF"，The corresponding number i s
0，Dial “ON”， The corresponding number is 1。
2. address Set（The initial ID: 1，as 000001）
ID DIP3—9 ID DIP 3—9 ID DIP 3—9 ID DIP 3—9
1 0000001 7 0000111 13 0001101 19 0010011
2 0000010 8 0001000 14 0001110 20 0010100
3 0000011 9 0001001 15 0001111 21 0010101
4 0000100 10 0001010 16 0010000 22 0010110
5 0000101 11 0001011 17 0010001 23 0010111
6 0000110 12 0001100 18 0010010 24 0011000
25 0011001 35 0100011 45 0101101 55 0110111
26 0011010 36 0100100 46 0101110 56 0111000
27 0011011 37 0100101 47 0101111 57 0111001
28 0011100 38 0100110 48 0110000 58 0111010
29 0011101 39 0100111 49 0110001 59 0111011
9
4

7、The Built-in Decoder：
①. JP1：RS485 and AC24V input：1P：485 A+；2P：485 B-；3、4P：
24VAC input。
②. JP2：120Ω485 termination resistance Jump line：485 communication in
the most distant communication lines between A and B through A 120 Ω
load resistance, in order to improve the reliability of communication.
③. JP3：Decoder board pan-tilt control output pin definition：
NO Cable color definition NO Cable color definition
1 BLACK COM 4 YELLOW LEFT
2 RED AUTO 5 GREEN DOWN
3 WHITE UP 6 BLUE RIGHT
④． JP4：Camera power supply and lens output pin definition:
NO definition NO definition NO definition
1 CAM 12V+ 3 LENS（COM） 5 LENS (FOCUS）
2 CAM 12V- 4 LENS（IRIS） 6 LENS (ZOOM）
4、Fundamental structure of pan-tilt：
5、Product external form dimension：
5
8
JP1:RS485 and
AC24V input
JP2:120Ω485 termination
resistance Jump line
JP3:Decoder board pan-tilt
control output pin definition
JP4:Camera power supply and
lens out pin definition
JP5:DIP switch

6、Assembly：
1．
Set up the Bracket, put the cable through the bracket.
2．
Connect the Pan-tilt with the bracket, fix the screw to the Ball Housing to
make sure waterproof.
3．
Connect the Power supply, video, RS 485 and lens controller cable to
the Pan-tilt, please refer to the Form 1 and Form 2.
4．
Check the IR Middle Speed dome whether works properly, if all is ok,
please use the screw to fix the Transparent Cover to the Ball Housing,
then installation finished.
5．
Pan-tilt Position-limit adjustment
pan-tilt Under may adjust position-limit , general horizontal condition by
hand movement, the product already has tuned up when leaving the factory
horizontal position-limit, the customer adjusts unnecessarily once again。
Initial value： level：０°－３５５° vertical：０°－９０°
When needing to carry out adjustment handle as follows: And then silk
loosens the horizontal position-limit piece fastening top , move the position-limit
piece when till required location, screwing down is equivalent to silk in being OK
again。
Figure 1、Pan-tilt rvvp
Figure 2、Iris rvvp
1 2 3 4
gray white purple green
zoom focus iris com
Figure 3、Camera and IR power cord
1 2 3 4
red black yellow green
Cam + Cam - IR + IR -
NO 1 2 3 4 5 6
Cable color red brown yellow green blue black
definition up down left right auto com
76