Kogan CLIMB AND SLIDE User manual

CLIMB AND SLIDE
PLAY SET
(NBPLYSTCNSA)

2
Safety & warning 3
Components 5
Assembly notes 8
Assembly 11
Cleaning & care 27
Specifications 28
Notes 29

3
Warning: Only for domestic outdoor use.
This playset satisfies all the requirements of the Australian standard
AS/NZS ISO 8124 and has been certified by an independent laboratory.
To guarantee safety, please give special attention to the assembly,
safety, and care instructions detailed in this document.
Important notice for timber care & maintenance
This product contains timber components that are naturally subject to deterioration in the
outdoor elements after years of exposure.
To combat the effects of outdoor exposure and greatly increase the lifespan of your play set
or cubby, we strongly recommend that you apply a protective coat of exterior grade lacquer
or oil to all timber parts upon first assembly. In order to best maintain the timber, we
recommend reapplying protective coats every 3-6 months.
Failure to care for your timber parts by applying protective lacquer or oil will greatly reduce
the lifespan of your product. For information on the most suitable exterior lacquer or oil,
please consult your hardware specialist.
Splits and Cracks
1. Splits and cracks will occur in timber as it expands and contracts with humidity and
temperature changes. They will occur particularly in the round pole timbers, but also
in square cut timber, and in both new and old sets. If the wood has a similar moisture
content to the natural surroundings, cracking is greatly reduced.
2. Whilst these can appear quite large and alarming, these cracks DO NOT affect the
strength, integrity, and durability of the play equipment. Splits or cracks over 10mm
should be considered dangerous as children could trap fingers within the openings –
tend to these large gaps immediately.
Prevention: Applying a timber preservative (such as oil, gel, or other suitable preservatives –
not included) can greatly help on preventing cracks and splits. Once it is applied, it can be
used to treat all exposed areas. However, this means that the outside of the wood may
have a higher moisture content. If it can be allowed to dry out slowly in more controlled
conditions, often taking up to three months, the end result will be a greatly reduced
incidence of cracking.
SAFETY & WARNINGS

4
General statements
Please familiarise yourself with the installation manual, parts/components and general
construction process of your new swing set before getting started. Approximate assembly
time: 6 to 8 hours. 2 metre unobstructed safety perimeter around swing set recommended.
This play set is designed for children 3-14 years old and for the use of:
•3 occupants who have a combined weight not exceeding 150 kgs on the elevated floor;
•1 occupant who has a total weight not exceeding 50 kgs on the climbing net; and
•for a total unit capacity of 5 occupants who have a combined weight of 250kg.
We recommend that the weight limits for all components must not be exceeded. Failure to
adhere to these and other safety guidelines could result in damage to the play set and
injury to the users.
Safety Advice
•As per legal requirements, a swing seat with flexible means of suspension must have a
40cm minimal distance between the ground and the swing. This distance is important
for safety. The distance between the swing seat and the ground, the trapeze and the
ground can be adjusted using the plastic height adjustment hooks.
•Warning: This product is only to be used by children between the ages of 3 and 14.
•Warning: Not to be used by anyone weighing over 50kgs.
•Warning: Choking hazard – small parts can be dangerous for children.
•Warning: It must be used under adult supervision.
•This product is for private use at home only. Under no circumstances is it be used in
parks, schools, camp sites, hotels, public leisure areas etc.
•The play set should be set up on a flat surface and two metres away from any
structures or obstacles (walls, trees, washing lines, cables etc).
•To avoid eye damage, we advise that the swing and slide should not be setup directly
facing the sun.
•The play set should be installed over impact absorbing surfaces such as sand, wood-
bark chips, rubber and foam and must NOT be set up on a hard surface (concrete,
tarmac etc). detail surfacing materials please refer attached consumer information
sheet.
•We recommend securing your swing set firmly into the ground using concrete.
•The anchorage must be checked regularly.
•Dispose of packaging thoughtfully.
•Do not allow children to play with packaging.
CAUTION! This Product includes timber and/or fabric, Please Keep away from fire.

5
IMPORTANT! For safety reasons, your play set must be embedded into the ground.
•Place your play set in the desired position and mark a square area 350mm x350mm
around each of the feet. Dig holes 350mm deep. The feet must be in the centre of the
square.
•Fill the holes with concrete. Do not exceed the ground level. Fit the embedding piece
into the centre of the concrete so that fixtures for screwing the posts into place rise out
of the concrete.
•When the concrete is dry, screw the posts to the embedding pieces.
•Anchors shall be placed level with or underground to reduce tripping hazards.
IMPORTANT! Wait until the concrete is set before using and check anchorages regularly.

6
Timber Parts
280001 (x1) 280002 (x2) 280003 (x1) 280004 (x1) 280005 (x2)
280006 (x1) 280007 (x2) 280008 (x2) 280009 (x2) 280010 (x11)
280011 (x1) 280012 (x2) 280013 (x1) 280014 (x1) 280015 (x3)
280016 (x5) 280017 (x2) 280018 (x5) 280019 (x1) 280020 (x2) 280021 (x1)
COMPONENTS

7
Fasteners
B131 Hex Head Bolt 5/16"
x 2 1/4" (x4)
B132 Hex Head Bolt 5/16" x
3 3/4" (x12) S06 Lag Bolt 1/4" x 2" (x12)
S65 Phillips Pan Head
Machine Screw 1/4" x 1
1/4" (x10)
B91 Hex Head Bolt 5/16"
x 2 1/2" (x4)
S95 Phillips Wood Screw #8
x 1" (x7)
S96 Phillips Wood Screw
#8 x 2" (x98)
S80 Phillips Wood Screw
#14 x 1 1/4" (x4)
S05 Lag Bolt 1/4 x 2 1/2"
(x11)
S97 Phillips Wood Screw
#8 x 1 1/2" (x16)
S91 Phillips Wood Screw
#8 x 1 1/4" (x27)
B115 Torx Pan Head Bolt
with teeth formed in under
head 5/16 x 1 1/2" (x6)
S119 Torx Pan Head Bolt
with teeth formed in
under head 5/16 x 2" (x2)
W07 USS Flat
Washer 1/4" (x33)
N01 T-Nut with
Barrel 1/4" (x10)
N02 T-Nut with
Barrel 5/16"
(x26)
W08 US Flat
Washer 5/16"
(x20)
MSC01 (x1) MSC02 (x1)
W14 Lock
Washer 1/4”
(x33)
W14 Lock
Washer 1/4”
(x20)

8
Accessories
HD23 (x4) AC17 (x4) AC15 (x5)
AC43 (x1) AC42 (x1) AC39 (x1)
SL06 (x1)

9
Additional Tools Required for Assembly
Tape Measure 610mm Level Angle Square
Phillips Screwdriver Cordless Drill or Electric
Drill
10mm Drive Ratchet or
Electric Impact Gun
Claw Hammer or Rubber
Mallet Pliers or Vise Grips 11mm Deep Well Socket
14mm Deep Well Socket 19mm Deep Well Socket 3mm, 6mm, 14mm and Drill
Bits
Phillips Head Screw Bits An adult with two adult helpers
Pre-Assembly Advice
Depending on your experience, assembly of our play sets can take as little as 6 hours up to
24 hours, including checking inventory of part; therefore, we recommend you set aside a full
two days for assembly.
Identify all the parts for your play set. Empty each box and lay out boards so you can see
each part. Your instruction book will have detailed drawings that will make it easy for you to
recognise individual parts. Keep all hardware and metal parts separate from wooden
pieces.
After everything is laid out, check carefully to ensure all parts are present. Make sure there
are no broken boards.
Find an area to sort your hardware. It is best to open the hardware on a solid surface so that
you do not lose any pieces in the grass. This will save time and familiarise you with all the
different pieces in the hardware bag.
As fresh timber acclimates to its new environment, the natural tendencies of the tree can
show itself in the form of checks or "cracks" in the lumber. In almost all cases this is normal
and it will not affect the structural integrity of your play set.
Cosmetic defects that do not affect the structural integrity of the product or natural defects
of wood such as warping, checking or any other physical properties of wood that do not
present a safety hazard, are not covered by this warranty.
Defects that develop because the products are exposed to extreme climate conditions are
not covered by this warranty. Defects that develop as a result of faulty or improper
installation of the product are also not covered by this warranty.
Most cracks are not warrantable, however if you believe that the integrity of your play set is
compromised by this natural occurrence, please contact the Dealer that you purchased
ASSEMBLY NOTES

10
your swing set from. We appreciate your purchase and know that you will enjoy your play
system for many years to come.
Important note: Wood has some natural defects such as knots, surface cracks, etc. We
reject parts that are structurally defective. We use a high-quality timber in our structures;
however, you should inspect each part for splinters or rough spots and sand them smooth
to prevent injury.
After familiarising yourself with all the components, read all instructions thoroughly.
Reading instructions after you have studied the parts will help you understand more clearly
the installation process and help to eliminate unnecessary mistakes.
Pay close attention to the diameter and length of each bolt and screw.
Never tighten hardware completely at first. It helps to have some adjustment for bolt
alignment while you are attaching parts together. After everything is square, tighten each
joint.
After the main unit is assembled it is critical that the floor is level and square. If the main
frame is not level, the walls and floor will be out of square.
After your complete installation, make sure every bolt, screw and nut are tight and every
board is secure. Wood will expand and contract with the seasons.
Place the set on level ground, not less than 2 metre from any structure or obstruction such
as a fence, garage, house, overhanging branches, laundry lines or electrical wires.
All 6mm and 10mm lag bolts must have pre-drilled holes 38mm to 50mm deep. Use a
3.175mm drill bit for the 6mm and 100mm lag bolt. Use pre-drilled holes in facias as a
reference for placing lag bolt pilot holes.
If a board lifts or rises causing a gap between boards when running in lag bolt or screws,
back out the screw or lag bolt and press or apply pressure (but not enough to crack or break
board) while re-running in the lag bolt or screw in the same hole.
Do not over tighten bolts, lag bolts or screws. You can damage boards, break hardware
and/or strip out the hardware. When using a hammer do not beat on the hardware, but
gently tap it in. Never beat on the wood as it will leave marks.
Levelling Your Swing Set During Assembly
Complete the steps which will be the basic frame of the fort [i.e. four corner posts with base
(sand box boards) and deck supports].
Position in the most level area chosen for the play set, keeping in mind the location and size
of the swing beam, ladder, slides, etc. That extend off the fort.
Once the frame is in the final position, check for vertical and horizontal levelness to
determine which side(s) will need to be dug into the ground to level the play set.

11
With a shovel, score the ground around the outside edges of the sandbox boards on the
'high' side of the fort. This is the area that will be dug in. Make sure to score deep enough;
the scored lines will be your digging template.
Push the frame off and away from the scored area, far enough to dig and remove dirt to
reach the appropriate depth.
Dig a channel along the scored line(s) for the base of the fort (corner post and sandbox
boards) to rest into. Dig the channels) to the same level depth. The bottom of the
channel(s) should be level to each other, so your frame doesn't teeter or rock because the
channel(s) are uneven.
Once you have removed enough grass and dirt, slide/push the frame into the channel(s).
Place a level on the vertical and horizontal boards of the frame to determine if enough soil
or too much, was removed.
Repeat this process until the basic frame is plumb and level and in its final position before
completing the rest of the assembly. Measure to make sure fort is square.
Important: if you require a channel depth of more than 150mm, then we recommend you
have your play set area professionally graded before completing assembly. **
Assembly Advice
•Follow the instructions exactly.
•This product must be assembled by adults.
•Once assembly has been completed, keep the instructions in a safe place for future
reference. This can be particularly handy for identification of parts if any after sales
service is required.
•Before commencing assembly, check that none of the parts are missing. If you find that
that you are missing a part, please contact our after-sales service department.
•Retain extra parts to use as spares in the future if necessary.
•Pre-Drill timber before fixing with screws to avoid cracks in the timber.
•The dimensions given in the instructions are indicative only, they may vary according to
the assembly method

12
Step 1:
ASSEMBLY

13
Step 2:

14
Step 3:

15
Step 4:

16
Step 5:
After installing the two side deck boards 280010,
there should be no gap between side 280010
and 280012/280017, all other deck boards
(280010/280020) should be evenly distributed.

17
Step 6:

18
Step 7:

19
Step 8:

20
Step 9:
After installing the two side boards
280016/280018, there should be no gap between
280016/280018 and 280012 , all other boards
(280016/280018) should be evenly distributed.