
How To Install The Spout
22
8
10
13
14
15
10
11
12
8
9
1
3
2
4
6
7
5
13
16
17
19
18
18
20
19
21
5
1230968-X2-C 21230968-X2-C 3
INSTALLATION
How To Install The Drain
INSTALLATION CHECKOUT
CARE AND CLEANING
For best results, keep the following in mind when
caring for your product:
Always test your cleaning solution on an
inconspicuous area before applying to the entire
surface.
Wipe surfaces clean and rinse completely with
water immediately after applying cleaner. Rinse and
dry any overspray that lands on nearby surfaces.
Do not allow cleaners to soak on surfaces.
Use a soft, dampened sponge or cloth. Never use
an abrasive material such as a brush or scouring
pad to clean surfaces.
The ideal cleaning technique is to rinse thoroughly
and blot dry any water from the surface after each
use.
Ensure that all connections are tight and
hat the handle is in the off position.
Turn on the drain and main water supply,
and check for leaks. Repair as needed.
Remove the aerator(22). Turn on the
faucet. Run hot and cold water through the
faucet about one minute to remove any
debris. Check for leaks. Repair as needed.
Shut off the faucet. Reinstall the aerator.
Assemble thumb screw (21) to link (20), and
link onto ball lever(18) with ‘V’-clip (19).
Slide lift rod (5) into the hole in link. Push
the ball lever down into the open position,
and adjust the lift rod. Tighten thumb
screw (21).
Remove stopper(14), flange(8) and
washer(10) from drain body(9). Take off
the tailpiece(11). Apply thread tape to
tailpiece and install the tailpiece to drain
body. Insert drain body kit into the lavatory
from underside, and make sure the drain
lever hole(12) facing to the back of the
lavatory. Screw the flange with washer into
the drain body. Tighten the locknut(13) by
hand from the underside of the fixture.
NOTE: If needed, apply a ring of plumbers
putty around the underside of the drain
flange(8), instead of using washer(10).
Place stopper(14) into drain body aligning
the flat side of stopper hole(15) with the
drain lever hole.
Remove the retaining nut(16). Fit the
plastic washer(17) and retaining nut onto
the ball lever(18). Insert the ball lever
assembly into the drain lever hole and
through the stopper hole. Tighten the
retaining nut.
Be sure that the ball lever(18) points to the
back of the lavatory, tighten the
locknut(13) on the drain body by wrench.
NOTE: Do not reposition the drain if
plumbers putty applied after the locknut is
tightened, or you may break the putty seal.
Wipe away excess plumbers putty.
Install the mounting stud (2) onto the faucet
body base (3). Insert lift rod (5) to the hole at
the rear of the body. Slide the washer (4)
over the flexible hoses (1) and mounting
stud, and into the groove at the bottom of
the faucet body.
Insert the faucet assembly into the lavatory
hole. Position the faucet. From underside of
the lavatory, place the bracket (6, Rubber
washer is on the top) onto the mounting
stud, and secure the faucet with the nut (7).
Attach the hoses to water supplies. When
facing front of the faucet , the left hose
connects to hot water, the right hose with
‘COLD’ label connects to cold water.
ขอแนะนะการติดตั้ง
ทดสอบการติดตั้ง
ขอสังเกต:
ขอสังเกต:
การดูแลรักษาและการทําความสะอาด
วิธีติดตั้งกอกนํ้า
วิธีติดตั้งสะดืออาง