Kraus KGW-1700 User manual

INSTALLATION MANUAL
www.kraususa.com I toll free: 1.800.775.0703 I © 2013-2014 Kraus USA Inc.
Single Lever Vessel Glass Waterfall
Bathroom Faucet
KGW-1700

Thank you for your purchase
We would like to take this opportunity to thank you for choosing Kraus.
We hope that you are completely satised with your purchase, and enjoy it for years
to come. If you have any questions, or require technical assistance, please contact
us at 800.775.0703 and one of our representatives will be happy to help.
For more information about Kraus products, please visit:
www.kraususa.com
In order to activate your warranty and get faster access to customer support, please
register your new Kraus product at:
www.kraususa.com/registration
Sincerely,
Kraus USA Customer Service

For technical assistance or replacement parts, please contact Kraus
Customer Service and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or [e-mail]
Prior to Installation:
• Make sure you have all necessary parts by checking the diagram and parts list. If
any part is missing or damaged, please contact Kraus Customer Service at 800-
775-0703 for a replacement
• Turn o the hot and cold water supply at the angle stops and turn on the old
faucet to release any built up pressure. Remove existing faucet. Clean sink or
countertop to remove any debris, plumber’s putty, or silicone
• Place bucket under angle stops. Turn on angle stops to ush any debris prior to
installing new plumbing. Shut o angle stops
• Pre-drilled hole size requirement: 1 3/8” (min)
• Max countertop thickness: 1 3/8”

Diagram and Parts List
1
2
3
4
5
8
96A
6B
6C
6D
7

Diagram and Parts List Tools you will need:
1
10
279
10 31/32”
Minimum distance 90mm
Less than 90mm
Cold Water
32 3/32”
Ø35~Ø38
1
23
10
9
11
12 13
Hexagon Nut
Hot
Water
Cold
Water
2 3
1
45
7
6
8
45
67
8
Ø1 3/8”~Ø1 1/2”
815
194
7 5/8”
Ø1 3/8~Ø1 1/2”
30˚
10 11
Close
Open Left
Hot Water
Push
25˚ 90˚
12
13
8
7
Ø35~Ø38
Max35
217
8 17/32”
Max1 3/8”
9
11
12 13
2
3
4
5
6
7
8
Adjustable Wrench
Phillips Screwdriver
Pipe Tape
1. Decorative Ring
2. Glass Disc
3. Lever
4. Seal for Glass Disc
5. Faucet Body
6. Mounting Hardware
(A) Rubber Washer
(B) Metal Washer
(C) Mounting Nut
(D) Mounting Screws
7. Hot & Cold Waterlines (2)
8. Hex Wrench
9. Manual

Dimensions
7 1/8"
(181mm)
1 1/4"-18UNEF-2A
2 5/16"
(59mm)
1/16"~1 3/4" (1mm~44mm)
2 1/8"
(54mm)
Ø 2 5/8"
(Ø67mm)
5/16"~3/8"
(7.2mm~8.8mm
58.2°
6 1/8"
(155mm)
12.5°
12.5°
11 1/4"
(286mm)
10 7/16"
(265mm)
12 11/16"
(322mm)
3 9/16"
(90mm)
7 11/16"
(195mm)
9/16"-24UNEF-2B
22 1/16"
(560mm)
12.5° 12.5°

Dimensions
7 1/8"
(181mm)
1 1/4"-18UNEF-2A
2 5/16"
(59mm)
1/16"~1 3/4" (1mm~44mm)
2 1/8"
(54mm)
Ø 2 5/8"
(Ø67mm)
5/16"~3/8"
(7.2mm~8.8mm
58.2°
6 1/8"
(155mm)
12.5°
12.5°
11 1/4"
(286mm)
10 7/16"
(265mm)
12 11/16"
(322mm)
3 9/16"
(90mm)
7 11/16"
(195mm)
9/16"-24UNEF-2B
22 1/16"
(560mm)
12.5° 12.5°

Step 1: Remove Mounting Hardware
Remove mounting hardware
(6A, B, C, & D) from the
mounting pipe
Step 2: Remove Decorative Ring
Remove decorative ring (1)
from faucet body (5)
6A
6B
6C
6D
6A
6B
6C
6D
5
5
1
1
2
5
blue Line
Cold
red Line
Hot
Open
Hot Cold
6A
6B
6C
6D
6A
6B
6C
6D
5
5
1
1
2
5
blue Line
Cold
red Line
Hot
Open
Hot Cold

Install glass disc (2) on faucet
body (5). Secure it using
decorative ring (1)
Step 4: Install Faucet
Insert faucet body (1) into
the hole on the countertop.
Attach rubber washer (6A),
metal washer (6B), mounting
nut (6C), and mounting screws
(6D) from underneath the sink
Step 3: Install Glass Disc
6A
6B
6C
6D
6A
6B
6C
6D
5
5
1
1
2
5
blue Line
Cold
red Line
Hot
Open
Hot Cold
6A
6B
6C
6D
6A
6B
6C
6D
5
5
1
1
2
5
blue Line
Cold
red Line
Hot
Open
Hot Cold
NOTE: Hand-tighten only
(decorative ring)

Step 5: Secure Mounting Hardware
Step 6: Connect Waterlines to Main Valve
Adjust direction of faucet body
(5). Tighten mounting nut (6C)
until snug. Tighten mounting
screws (6D) to nut with a
Phillips head screwdriver until
snug
Connect hot and cold waterlines
(7) to the angle stops. Tighten
with a wrench until snug. Turn
on hot and cold angle stops and
check for leaks
6A
6B
6C
6D
6A
6B
6C
6D
5
5
1
1
2
5
blue Line
Cold
red Line
Hot
Open
Hot Cold
6A
6B
6C
6D
6A
6B
6C
6D
5
5
1
1
2
5
blue Line
Cold
red Line
Hot
Open
Hot Cold
6A
6B
6C
6D
6A
6B
6C
6D
5
5
1
1
2
5
blue Line
Cold
red Line
Hot
Open
Hot Cold
NOTE: Make sure O-rings
are installed on both
ends of the hot & cold
waterlines

Step 7: Flush Faucet
Turn water on for a minute to
ensure proper water ow
6A
6B
6C
6D
6A
6B
6C
6D
5
5
1
1
2
5
blue Line
Cold
red Line
Hot
Open
Hot Cold

Replacement Parts
1A
1B
2
3
4
5
6
7
8
9A
9B
9C
9D
10
1. (A) Decorative Ring
(B) O-ring
2. Glass Disc
3. Lever
4. Seal for Glass Disc
5. Locking Nut
6. Cartridge
7. Flow Restrictor
8. Hot & Cold Waterlines
9. Mounting Hardware
(A) Rubber Washer
(B) Metal Washer
(C) Mounting Nut
(D) Mounting Screws
10. Hex Wrench

Trouble - Shooting
If you have followed the instructions carefully and your faucet still does not work
properly, take the following corrective steps:
PROBLEM CAUSE ACTION
Leakage under the
handle
Locking nut has come
loose
Unscrew the decorative
ring (by hand) and
remove the glass disc.
Loosen set screw with
a hex wrench located
underneath lever and
remove lever. Tighten
locking nut with a
reversible wrench
Water will not shut off
completely
Cartridge may be
defective
Unscrew decorative
ring (by hand) and
remove glass disc.
Loosen set screw with
a hex wrench located
underneath lever and
remove lever. Unscrew
locking nut with a
reversible wrench.
Remove ceramic disc
cartridge. Check for
cracks
Drain is leaking Washers may be
compromised or
installed incorrectly
Check washers to make
sure they are installed
correctly and not
cracked

Codes/Standards Applicable:
NSF/ANSI 372
NSF/ANSI 61
ASME A112.18.1M
2.2GPM 8.3L/min maximum
LEAD FREE
IAPMOR&T
TM
HELP LINE
Our customer service hours are Monday – Friday, 9am – 8pm EST.
Be sure to visit our website at www.kraususa.com
If you are a homeowner please contact a Kraus Customer Service Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
Toll-free 800-775-0703
[email protected]
If you are a plumbing contractor or trade professional please contact a Kraus Pro
Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
516-801-8955
Proser[email protected]
If you are an Authorized Partner please contact a Partner Support Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
516-801-8954
Partnersuppor[email protected]
In requesting warranty service, please be ready to provide:
1. Proof of purchase.
2. A description of the problem.

Care & Maintenance
*To keep the product clean & shining, follow the steps below:
1. Rinse with clean water & dry with a soft cloth
2. Do not clean with soaps, acid, polish, abrasives, or harsh cleaners
3. Do not use cloth with a coarse surface
4. Unscrew the aerator and clean when necessary
*This installation manual is subject to change without further notice.
1
10
279
10 31/32”
Minimum distance 90mm
Less than 90mm
Cold Water
32 3/32”
Ø35~Ø38
1
23
10
9
11
12 13
Hexagon Nut
Hot
Water
Cold
Water
2 3
1
45
7
6
8
45
67
8
Ø1 3/8”~Ø1 1/2”
815
194
7 5/8”
Ø1 3/8~Ø1 1/2”
30˚
10 11
Close
Open Left
Hot Water
Push
25˚ 90˚
12
13
8
7
Ø35~Ø38
Max35
217
8 17/32”
Max1 3/8”
9
11
12 13
2
3
4
5
6
7
8
Download the Kraus Care & Maintenance Guide at:
http://www.kraususa.com/maintenance

Receive Proof of Ownership
Access Customer Care & Installation Help
Get Exclusive Kraus Oers & Promotions
Scan to Register Online
or visit http://www.kraususa.com/registration
Please take a moment to share your experience.
Visit http://www.kraususa.com/review to let us know what you think
about your new Kraus product.
Contact Us to Learn More
1.800.775.0703 / www.kraususa.com / [e-mail]
Like & Follow KrausUSA
Download the Kraus Care & Maintenance Guide at:
http://www.kraususa.com/maintenance
www.kraususa.com
REGISTER YOUR PRODUCT TODAY
We’re always looking for ways to improve.