Kraus Turino KFDW1-33 User manual

www.kraususa.com I Toll Free: 1.800.775.0703 I © 2021 Kraus USA Inc. I REV. June 15, 2021
Fireclay Dual Mount
Workstation Kitchen Sink
KFDW1-33
R
INSTALLATION MANUAL

Congratulations on the purchase of your new Kraus plumbing fixture!
Please keep the box and packaging materials until your product is completely installed. If you have
any questions, require technical assistance or have any problems with your product:
Please contact our Customer Service Team
1-800-775-0703 / [email protected]
Have the model number available and retain a copy of your receipt with purchase date for
reference.
If for any reason this product does not meet your expectations, please be sure to repack this
product in the original box and packaging material to avoid damage during transit.
DO NOT RETURN TO STORE
STOP
2

3
Prior to Installation:
·Inspect the sink prior to installation to make sure the sink has not been damaged
during shipping.
·Observe all plumbing and building codes according to your state requirements.
·Additional floor and wall preparation may be required to avoid damaging the sink.
·Make sure to purchase the correct cabinet for your kitchen sink. Base cabinets
should be 3" larger than the actual size of the sink.
·Not recommended to be installed with laminate countertop.
For technical assistance or replacement parts, please contact Kraus
Customer Service and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or [email protected]
The step-by-step guidelines in the installation instructions are a general reference for
installing a Kraus Sink. Should there be any discrepancies, Kraus cannot be held liable. It is
recommended to install all Kraus products by hiring a licensed professional.

Tools you will need:
4
NOTE: Specialized tools may be necessary to install Kraus Fireclay sinks with
countertop materials other than wood, marble or granite.
Phillips Screwdriver Pencil
Tape Measure Screwdriver Level
Safety Goggles Silicone Adhesive Jig Saw Acetone
Drill
Dimensions
KFDW1-33
33 1/8" x 19 1/2" x 10"
ACETONE
R 5/8"
(15mm)
33 1/8" (842mm)
30 1/2" (775.65mm)
19 1/2" (497mm)
17" (430.76mm)
15 3/4" (400.27mm)
4 3/8" (112mm)
3 1/2"
(90mm)
10"
(254mm)

5
Undermount Installation
1. Measure & Build Supports
·Build supports on inside of cabinet based on sink measurements
Installer Tip: Support options
·1 1/4" Angle Irons
·(2) 2" x 4'
·3/4" Plywood
NOTE: Due to the typical ±3mm side wall
variance in manufacturing, it is recommended
that you design / modify the sink cabinet to
match your clients individual sink(s) need.
SUPPORTS

6
2. Install Sink
·Place sink in opening. The weight of sink should be sustained
by the built supports.
·Make sure sink is leveled from front to back and side to side
·Make sure the top of the sink is flush with the top of the cabinet
·Uses silicone to fill in gaps where necessary

7
3. Cut Countertop
·Kraus recommends providing the cabinet maker with the actual sink to be installed prior
to the cabinet fabrication.
·It is recommended that the sink be installed with an approximately 1/8" positive reveal.
It is further recommended that the installer(s) discuss this with the customer and agree
that this finished appearance is the desired effect.

8
Installer Tip: Use acetone or denatured alcohol to remove any excess sealant.
4. Install Countertop
·Use a bead of silicone (or preferred adhesive) around the rim of the sink. Check the
alignment of the sink to the cutout in the countertop. Place countertop cutout hole over
sink and press firmly.
Silicone Adhesive

9
5. Installing Plumbing and Fixtures
·Connect drain, trap to drain and water supply connections to the faucet according to
manufacturer's instruction.
·Run water into sink and check for leaks.
·Note: Before installation, please check that the drain kit complies with ASME
A112.18.2/CSA B125.2 and with CUPC certification.

10
Top Mount Installation
1. Measure & Build Supports
·Build supports on inside of cabinet based on sink measurements
·The supports should be flush with the top of the cabinet
Installer Tip: Support options
·1 1/4" Angle Irons
·(2) 2" x 4'
·3/4" Plywood
NOTE: Due to the typical ±3mm side wall
variance in manufacturing, it is recommended
that you design / modify the sink cabinet to
match your clients individual sink(s) need.
SUPPORTS

11
NOTE: Make sure clearance is suitable for
backsplash, faucet and plumbing for the sink.
2. Measure Sink Opening
·Using the measurements of the sink, mark the countertop where it needs to be cut.
Traced Line

12
3. Cut Countertop
·Cut the opening in the countertop by carefully following the traced line.
NOTE: Please use the appropriate saw
that best fits your countertop material.

13
4. Apply Silicone or Plumber's Putty
·Clean and dry the surface around the opening of the sink.
·Turn the unit upside down to apply sealant. Apply silicone-based sealant (not included)
underneath the edge of the sink.
Silicone Adhesive

14
5. Secure Sink to Countertop
·Insert the sink into the opening, check the alignment of the sink to the cutout in the
countertop and press firmly.
·Remove excess silicone-based sealant.
·Allow sealant to set for 30-60 minutes.
·Note: Before installation, please check that the drain kit complies with ASME
A112.18.2/CSA B125.2 and with CUPC certification.

15
Codes/Standards Applicable:
Fireclay Kitchen Sink Warranty
Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. (“Kraus”).
Kraus extends this warranty to the original purchaser for personal household use of the “Fireclay Kitchen Sink” in its original
location. The warranty is non-transferable.
Kraus warrants the structure and finish of the product to be free from defects in material and workmanship under normal
usage for a period of five (5) years. The warranty commences from the initial date of purchase by the owner or trade
professional, from an authorized Kraus dealer, through the five (5) year term of the original owner or end-user.
Any product reported to the authorized dealer or to Kraus as being defective within the warranty period will be repaired or
replaced with a product of equal value at the option of Kraus. This warranty extends to the original owner or end-user, and
is not transferable
to a subsequent owner.
Restrictions
This warranty does not cover antediluvian, discontinued, or display products, whether such items are purchased at discount
outlets, unauthorized dealers, and/or sold on clearance.
This warranty does not cover instances of negligence, misuse, abuse, improper installation, carelessness, accident, hard
water or mineral deposits, exposure to corrosive materials, misapplication, damages caused by improper maintenance,
alteration of the product, or failure to follow care or installation instructions enclosed with your product. Avoid using
abrasive cleaners such as powders, bleach, ammonia, alcohol, or chlorine. Avoid using abrasive pads, steel wool, or wire
brushes, as these will damage and wear down the finish.
This warranty does not apply to Products that have not been installed or operated in accordance with instructions supplied
by Kraus and all applicable rules, regulations, and legislation pertaining to such installations.
Kraus USA recommends that all Kraus products are installed by fully licensed and insured trade professionals with
experience in the installation of bathroom and/or kitchen manufactured goods.
This warranty does not cover labor charges or costs of removal and reinstallation of said product. This warranty does not
allow recovery of incidental or consequential damages, such as loss of use, delay, property damage, or other consequential
damages, and Kraus accepts no liability for such damages.
This warranty does not cover Marine or Outdoor Installation.
This warranty does not cover any free gifts included with purchase.
Except as otherwise provided above, Kraus makes no warranties, expressed or implied, including warranties of
merchantability and fitness for a particular purpose, or compliance with any code.
Shipping charges will be covered for the first (1) year of the warranted replacement part or product (HI, AK, and Puerto Rico
shipping charges may apply). International shipping fees are not included.
UPC
CR

If you are a homeowner please contact a Kraus Customer Service Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
Toll-free 800-775-0703
[email protected]
If you are a plumbing contractor or trade professional please contact a Kraus Pro Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
516-801-8955
[email protected]
If you are an Authorized Partner please contact a Partner Support Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
516-801-8954
[email protected]
In requesting warranty service, please be ready to provide:
1. Proof of purchase.
2. A description of the problem.
Download the Kraus Care & Maintenance Guide at:
http://www.kraususa.com/maintenance
Commercial Warranty
Kraus extends the above warranty for a period of one (1) year to purchasers of products for industrial, commercial, and
business use.
All incidental or consequential damages are specifically excluded. No additional warranties, express or implied, are given,
including but not limited to any implied warranty of merchantability or fitness for a particular purpose.
Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an
implied warranty lasts, so the above limitations or exclusions may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
KRAUS USA has the right to change, modify, and/or update the warranty policy at any time. For the latest, most up to date
comprehensive warranty, go to www.kraususa.com/warranty.
16

Register Your Kraus Product
Activate Your Warranty
Access Premium Customer Support
Get Product Information
REGISTER TODAY
http://www.kraususa.com/registration
R
www.kraususa.com
IMPORTANT