Kraus Cirrus FUS-13102 User manual

INSTALLATION MANUAL
Cirrus 4” Centerset Basin Faucet
FUS-13102
www.kraususa.com I toll free: 1.800.775.0703 I © 2014-2015 Kraus USA Inc.

Thank you for purchasing Kraus
We would like to take this opportunity to thank you for your business with Kraus
USA. It is our sincere hope that you are completely satised with your experience.
We welcome any questions or comments you may have, and will be glad to assist
you in the future.
For more information about Kraus products, please visit our website at:
www.kraususa.com
Please register your new Kraus product at the following web address in order to
activate the warranty and receive the full benet of customer support:
www.kraususa.com/registration
Sincerely,
Kraus Customer Service Department

Prior to Installation:
• Make sure you have all necessary parts by checking the diagram and parts list. If
any part is missing or damaged, please contact Kraus Customer Service at 800-
775-0703 for a replacement
• Turn o the hot and cold water supply at the angle stops and turn on the old
faucet to release any built up pressure. Remove existing faucet. Clean sink or
countertop to remove any debris, plumber’s putty, or silicone
• Place bucket under angle stops. Turn on to ush any debris prior to installing new
plumbing. Shut o angle stops
• Max countertop thickness: 1-3/8”
Tools you will need:
Adjustable Wrench Safety Goggles Bucket
Plumber’s Putty
6 5/8”
5 4/5”
3/8”
(10mm)
7/8”
19.7º(22mm)
8 5/16”
1 1/4-18UNF-2A
(21mm)
10 1/8”
(257mm)
1 3/8”
(35mm)
3 3/4”
(168mm)
(147.3mm)
(96mm)
∅ 1 3/4”
(
∅ 45mm)
∅ 1 15/16”
(
∅ 50mm)
9/16”-18UNEF
27mm ~ 41.3mm 1 1/16” ~ 1 5/8”
∅ 1 15/16”
(
∅ 50mm)
12 7/16”
(316mm)
1 5/8”
(42.5 mm Max)
7A
8B
8C
8D
8A
7A
8B
8C
8D
8A

FUS-13102 Diagram and Parts List
A
B
C
D1
D2
D3
A. Faucet Body
B. Putty Plate
C. Mounting Nut
D. Aerator Assembly
D1. Aerator Washer
D2. Aerator
D3. Aerator Cover

Faucet Dimensions

Lift Rod Drain Diagram and Parts List
a
b
c
d
e
f
g
ijkl m
n
o
p
h
a. Waste Stopper
b. Drain
c. Rubber Washer
d. Concave Washer
e. Plastic Washer
f. Mounting Nut
g. Tailpipe Washer
h. Tailpipe
i. Top Hat Washer
j. Drain Off Pole
k. Washer
l. Retaining Nut
m. Extender Rod
n. Clip
o. Thumb Screw
p. Lift Rod

Lift Rod Drain Dimensions
a
b
c
d
e
f
g
ijkl m
n
o
p
h

Step 1: Remove mounting hardware
Remove mounting nut (C) and
putty plate (B) from threaded
mounting pipe
Step 2: Install faucet
Apply a small amount of putty
to groove along bottom outer
edge of putty plate (B). Secure
putty plate to faucet. Install
faucet through holes in sink or
countertop
AA
B B
C
C
C
C
Plumbers Putty
D1
D2
D3
AA
B B
C
C
C
C
Plumbers Putty
D1
D2
D3
Installer Tip: Make sure hole
on putty plate (B) is positioned
to the rear of the faucet for the
lift rod to go through

Step 3: Secure faucet
Tighten mounting nuts (C) onto
threaded mounting pipe from
underneath the countertop or sink
(HAND-TIGHTEN ONLY)
Step 4: Connect waterlines to main valve
Thread hot & cold waterlines (not
included with faucet) to threaded
mounting pipe. (A. Hot Side: Left
B. Cold Side: Right). Secure other
end of waterlines to angle stops.
Tighten both ends with adjustable
wrench until snug. Turn on angle
stops and check for leaks (DO NOT
TURN ON FAUCET)
AA
B B
C
C
C
C
Plumbers Putty
D1
D2
D3
AA
B B
C
C
C
C
Plumbers Putty
D1
D2
D3
Installer Tip:
Recommended waterlines:
3/8 in. OD x 1/2 in. IPS

Step 5: Install Drain
a
b
c
d
e
f
g
poo
nn
m
l
p
m
d
g
b
h
a
b
b
c
e
f
h
ikl
o
p
H1
H2
H3
jklj
1
2
3
4
5
6
7
poo
n
j
hk
l
n
m
12
po
p
m
d
g
b
h
a
b
b
c
e
f
8
911 12
D1
D2
D3
j
1
2
3
4
5
6
7
poo
n
j
hk
l
n
m
12
po
p
m
d
g
b
h
a
b
b
c
e
f
8
911 12
D1
D2
D3
j
• Remove waste stopper (a) from
drain (b). Remove tail pipe (h),
mounting nut (f), plastic washer
(e), and concave washer (d) from
drain (b). Remove retaining nut
(l) and washer (k) from tailpipe
(h)
• Install drain (b), with rubber
washer (c) attached, into the drain
hole. Attach concave washer (d)
with narrow end up, plastic washer
(e), and mounting nut (f) to drain
(b) from underneath countertop or
sink. Secure tightly to sink with an
adjustable wrench
• Thread tailpipe (h) onto drain (b)
and hand-tighten. Adjust tailpipe
(h) so drain o pole opening is to
the rear of the sink
Installer tip: Leave top hat
washer (g) in tailpipe (h)
Installer Tip: Make sure
tailpipe washer (g) is installed
in tailpipe (h)

Step 5: Install Drain
1
2
3
4
5
6
7
poo
n
j
hk
l
n
m
12
po
p
m
d
g
b
h
a
b
b
c
e
f
8
911 12
D1
D2
D3
j
1
2
3
4
5
6
7
po
o
n
j
hk
l
n
m
12
po
p
m
d
g
b
h
a
b
b
c
e
f
8
911 12
D1
D2
D3
j
1
2
3
4
5
6
7
po
o
n
j
hk
l
n
m
12
p
o
p
m
d
g
b
h
a
b
b
c
e
f
8
911 12
D1
D2
D3
j
• Insert waste stopper (a) into
drain (b). Make sure slot at end
of waste stopper (a) is facing the
rear of the sink
• Insert lift pole rod (p) through the
hole in the back of the faucet body.
Loosen thumb screw (o) and attach
extender rod (m) to lift pole rod (p).
Tighten thumb screw (o)
• Insert shortest end of drain o
pole (j) into drain o pole opening
of tailpipe (h). Make sure drain o
pole (j) and slot on waste stopper
(a) engage. Attach washer (k) and
retaining nut (l) through drain o pole
(j). Secure retaining nut (l) to drain o
pole opening of tailpipe (h)

Step 5: Install Drain
Step 6: Flush Faucet
• Place one end of clip (n) on drain
o pole (j). Insert drain o pole (j)
through desired hole of extender
rod (m). Place other end of clip (n)
on drain o pole (j)
Remove aerator assembly (D).
Loosen aerator cover (D3) with
adjustable wrench. Remove
aerator (D2) and aerator
washer (D1). Turn water on for
1 minute to remove any debris.
Reassemble aerator assembly (D)
Installer Tip: You may adjust
the extender rod (m) to a
desired height
AA
B B
C
C
C
C
Plumbers Putty
D1
D2
D3
1
2
3
4
5
6
7
poo
n
j
hk
l
n
m
12
p
o
p
m
d
g
b
h
a
b
b
c
e
f
8
911 12
D1
D2
D3
j

Replacement Part List - FUS-13102
1
2
3
4
5
12
11
13
10
9
8
7
6
1. Metal Handle – HOT
2. Cartridge – HOT
3. Aerator Washer
4. Aerator
5. Aerator Cover
6. Metal Handle – COLD
7. Cover Button
8. Set Screw
9. Decorative Ring
10. Cartridge – COLD
11. Putty Plate
12. Mounting Nut
13. Hex Wrench

1
2
3
4
5
6
7
9101112 13
14
15
16
8
1. Waste Stopper
2. Drain
3. Rubber Washer
4. Concave Washer
5. Plastic Washer
6. Mounting Nut
7. Tailpipe Washer
8. Tailpipe
9. Top Hat Washer
10. Drain Off Pole
11. Washer
12. Retaining Nut
13. Extender Rod
14. Clip
15. Thumb Screw
16. Lift Pole Rod
Replacement Part List - Lift Rod Drain

Trouble - Shooting
If you have followed the instructions carefully and your faucet still does not work
properly, take the following corrective steps:
PROBLEM CAUSE ACTION
Leakage under handles Hot or cold cartridge (2
or 10) may be loose
Remove cover button
(7). Loosen set screw (8)
with hex wrench (13).
Remove metal handle (1
or 6). Tighten hot or cold
cartridge (2 or 10) with
adjustable wrench
Aerator drips or has
inconsistent water flow
pattern
Aerator (4) may be dirty
or not seated properly
Unscrew aerator cover
(5) with adjustable
wrench. Remove
aerator (4) and clean
out debris
Water will not shut off
completely
Hot or cold cartridge (2
or 10) may need to be
adjusted or replaced
Remove cover button
(7). Loosen set screw (8)
with hex wrench (13).
Remove metal handle
(1 or 6). Remove hot or
cold cartridge (2 or 10)
with adjustable wrench.
Check for cracks
Drain is leaking Washers may be
compromised or
installed incorrectly
Check washers to make
sure they are installed
correctly and not
cracked

Care & Maintenance
*To keep the product clean & shining, follow the steps below:
1. Rinse with clean water & dry with a soft cloth
2. Do not clean with soaps, acid, polish, abrasives, or harsh cleaners
3. Do not use cloth with a coarse surface
4. Unscrew the aerator and clean when necessary
*This installation manual is subject to change without further notice.
1
10
279
10 31/32”
Minimum distance 90mm
Less than 90mm
Cold Water
32 3/32”
Ø35~Ø38
1
23
10
9
11
12 13
Hexagon Nut
Hot
Water
Cold
Water
2 3
1
45
7
6
8
45
67
8
Ø1 3/8”~Ø1 1/2”
815
194
7 5/8”
Ø1 3/8~Ø1 1/2”
30˚
10 11
Close
Open Left
Hot Water
Push
25˚ 90˚
12
13
8
7
Ø35~Ø38
Max35
217
8 17/32”
Max1 3/8”
9
11
12 13
2
3
4
5
6
7
8

Codes/Standards Applicable:
KRAUS LIMITED LIFETIME WARRANTY
This product has been manufactured and tested to the highest quality standards
by Kraus USA Inc. (“Kraus”). We offer our customers thoughtfully crafted fixtures
& accessories, engineered for enduring performance over years of use.
WHO IS COVERED BY THE WARRANTY
This warranty extends to the original purchaser only. This warranty is not
transferable, between homes or owners and is only applicable to residential use.
WHAT IS COVERED BY THE WARRANTY
Kraus warranties this product against defects due to material or craftsmanship
error during the warranty period: Kraus will provide replacement parts at
no charge, or at its option, replace any product or part of the product that is
deemed defective, under normal installation, use, service and maintenance. If
Kraus is unable to provide a replacement and repair is not practical or cannot
be made in timely fashion, Kraus may elect to refund the purchase price in
exchange for the return of the product.
CONDITIONS AND EXCLUSIONS
Like other home fixtures, Kraus products will require light maintenance to
ensure proper function. We provide you with complete knowledge to perform
this maintenance and can also recommend resources if you are unable to fulfill
this service.
A. Kraus will not be responsible for product failures due to lack of maintenance
or proper use. Please read your care and maintenance documentation to deter-
mine the limits of proper use.
B. The original sales receipt, order number, and/or proof of purchase must be
presented at the time of the warranty claim, without exception, for this warranty
to be applied to all Kraus products.
NSF/ANSI 372
NSF/ANSI 61 ASME A112.18.1M
1.5GPM 5.7L/min maximum
GREEN
Water Eciency
LEAD FREE
IAPMOR&T
TM

C. Kraus recommends installing all Kraus products with a licensed, professional
plumber. Kraus will not be held responsible for any damage or product failure
due to improper installation, misuse, or failure to use a licensed professional.
Please read your care and maintenance documentation to determine the limits
of proper use.
D. Commercial use will automatically void this warranty.
E. This warranty is not applicable to Kraus products purchased from an unau-
thorized seller. For a complete list of authorized sellers please visit http://www.
kraususa.com/where-to-buy.html
NONAPPLICABILITY OF THIS WARRANTY
By the purchase and use of our products, you agree that Kraus is not liable
for incidental, consequential or special damages associated with the return,
replacement, installation or use of your product. This includes freight costs,
cartridge replacement, labor, travel time, lost profit, home damages and other
contingent liabilities and costs (including, without limitation, costs associated
with experts, investigations, analyses, attorneys and other professionals and
services). The Kraus warranty is a comprehensive and explicit limit of liability,
and all items outside of it are not addressable by or the responsibility of
Kraus. Certain states have variances regarding implied warranties and in those
situations we remain fully compliant.
KRAUS USA Inc. makes no implication that products comply with any or all local
building or plumbing codes. It is the consumer’s responsibility to determine
local code compliance. This warranty extends to the original purchaser and first
consumer.
HELP LINE
For additional assistance at any point in the installation process, please call us at
1.800.775.0703 or email us at [email protected]
Our customer service hours are Monday – Friday, 9am – 8pm EST.
Be sure to visit our website at www.kraususa.com

www.kraususa.com

www.kraususa.com