KT KMR200 User manual
Data
YYMMDD
1234567
123456789012345
ktEgg_123
moda12345
-Later on, after connection is completed, execute the
Web browser to verify the internet connection.
MSIP-CRM-MDJ-KMR200
Front
Side
Rear
Side
12 4 5
Micro USB port
(for charging main body)
8
Initialization Button
6USIM Cover
9
Nano
USIM Slot
7
a LTE signal strength
b Message Display
Window
c No of WiFi connections
The accessories can be changed without notice due to performance enhancement or other reasons.
Please be careful not to damage on the metal
area of USIM when inserting or releasing.
Inserting a USIM card with wet hands
may cause a damage in USIM.
Using other accessories except the supplied items may cause failure in product,
please use the supplied items.
Memo
●Power On
-Pressing & holding [Power(OK)] button for more than 3 sec displays
on LCD screen.
-After LCD On, it takes approximately 20~30 seconds to complete a booting.
●Window 7
-Select [Start▶Control Panel▶Network & Sharing Center]
-Select [Network Connection]
-Select the [ktEgg_xxx] among WiFi names shown in [Wireless
Network Connection] and then click [Connect] Button.
※ “xxx” refers to the terminal number or the
unique number of English characters .
-Open the USIM cover in main body and copy ‘KEY’
(WiFi Password) value on the attached label, then input the
value to a window “Network Security Key Input”.
●Power Off
-Pressing & holding [Power(OK)] button at the side of product for more than
3 seconds results in Off state of LCD in the product.
-Power goes Off right after LCD Off.
●Entering Power Saving Mode
-To enter Power Saving Mode, press & hold [Power Saving(Next)]
button for 3 seconds causes LCD Off.
-Power Saving Mode display automatically goes off after 20-40 seconds.
●Releasing Power Saving Mode
-Pressing & holding [Power Saving(Next)] button for 3 seconds in Power Saving Mode
results in LCD On.
-Power Saving Mode is released after LCD On.
Power Saving / Next Button
●Press & Hold: Entering/Releasing Power Saving Mode
●Press: Move to next menu
Power / OK Button
●Press & Hold: Power On/Off
●Press: Menu Selection
● This product requires separate circuit contract with a specified service provider, KT.
● The pictures and images in this user guide may be different from real product.
● The software version of this product can vary depending on the conditions of the service provider,
and can be changed without a notice.
Ver 1.0
6. Procedures for Charging
7. Power On/Off and Entering/Releasing Sleep Mode 8. WiFi Connection
●
Charging with a charger
Frequently Asked Questions
Warranty
Ver 1.0
FAQ
KMR200
Function
f. Bluetooth
(loss prevention)
Loss Prevention Function in
operation
Loss Prevention Function Off
USB Tethering Function On
USB Tethering Function Off
Battery Remains (100~80%)
Battery Remains (79~60%)
Battery Remains (59~40%)
Battery Remains (39~20%)
Battery Remains (19~1%)
Battery Remains (below 1%)
Battery Charging in Progress (5 levels)
Battery Charging completed
Data Usage Display (GB)
Data Usage Display (MB)
g. USB Tethering
h.Battery Remains
i.Data Usage
Name
Name
Function
LTE signal strength (very strong)
LTE signal strength (strong)
a. LTE signal LTE signal strength (moderate)
LTE signal strength (relative weak)
LTE signal strength (weak)
LTE signal strength (no signal)
b. Message Display of Terminal status,
DisplayWindow
Current time, Functional Menu
c. No of WiFi Display of the number of
WiFi connections
In use of 2.4GHz WiFi Frequency
USB
port
Charger
Power outlet Mcro USB
port
Mcro USB
port
Ver 1.0
KMR2
00
User Guide
This user guide describes the methods for using this product.
Please read this user guide carefully for correct use before using this device.
This product is a portable wireless port sharing device that offers wireless internet
service connection to a variety of terminals by altering LTE or WiBro signals into WiFi or
USB. In addition, this product allows users to enjoy in various ways in a car or indoors
by connecting an USB cable supplied as an accessory and users can use this product
simply and conveniently through its dedicated App (my URoad).
This product offers various specialized functions other than wireless internet functions
so that users can use. Please smartly use this product by utilizing those functions.
Use in various environments with USB cable
Main Body
User Guide
LCD Display
Charger
Power Saving Button
(Next)
Power On Button(OK) USB port (external battery output)
Charging Status LED
USB cable USB
cable strap
FAQ
(Frequently Asked Questions)/
Warranty
Pouch
This product can be connected to the battery charger in a car, adapters or PCs /Mac via USB cable.
1. Major Functions
3. Name of Each Part 4. LCD Status Display 5. Procedures to
Insert USIM card
2. Accessories included
External battery power function
This product can charge other devices using USB cable.
Loss Prevention
When a Smart Phone or a tablet is away certain distance from this product(egg), or location of
this product(egg) is unknown, the mobile App (my URoad) in Smart Devices informs the location of
egg or alarms user for distance away of egg so that a loss of egg can be prevented.
-Connect USB cable to a charger
-Connect the micro connector of USB cable
to the micro connector of a main body
of KMR200
-Connect a charger to AC power outlet
●
Charging with USB cable
(via PC connection)
-Connect USB cable to USB port in PC
-Micro connector of USB cable to the micro
connector of a main body of KMR200
3.
Close the USIM cover.
3
f Bluetooth (loss prevention)
g USB Tethering
h Battery Remains
i Data Usage
e Easy Share
d WiFi Frequency
strength
connections
Expression Expression
d.WiFi Frequency
e. Easy Share Easy Share (Guest WiFi) in operation
OFF Easy Share (Guest WiFi) Off
In use of 5GHz WiFi Frequency
OFF
OFF
1.
Open the USIM cover located at the side.
YYMMDD
1234567
123456789012345
ktEgg_123
moda12345
2.
Place the metal face of
USIM up and push the
USIM insert into a slot
until hearing clicking
sound.
Charging Status LED lights on Red and turns to
Green after fully charged
Charging status of battery can be checked
through LCD display during charging
When charging the product, please make sure
to use specified charger and USB cable.
Unauthorized chargers or USB cables may
cause a failure of product.
In Power Saving Mode, pressing either [Power Saving(Next)] button or [Power(OK)] button can check the status.
It is very convenient to use the product, since a “reserved power saving” function in my URoad
[mobile App] or Web setting screen allows to enter or release Power Saving Mode automatically
as predetermined settings.
PC connection via USB cable for charging
the product requires more time than using
AC power with a charger.
Press and hold the
[Power Saving(Next)]
button for about
3 seconds
Press and hold the
[Power (OK)] button
for about 3 seconds
Data
Data
Name Function
①LCD Display Display of operational status and functional menu
Press & Hold (for over 3 sec): entering/releasing power saving mode
②Power Saving Button (Next) Short Press: Menu selection (Next)
③Charging Status LED LED for displaying charging status (Charge in progress: Red / Charge completed: Green)
Press & Hold (for over 3 sec): Power On/Off
④Power On Button(OK) Short Press: Menu selection (OK)
⑤USB port (External Battery output) USB port for external battery function (charging other devices)
Short Press: Restart
⑥nitialization Button Press & Hold (for over 10 sec): Initialization
⑦Nano USIM Slot Slot for USIM installation
⑧Micro USB port USB port for either charging main body or data communication
⑨USIM Cover Product Protection (product label, Initialization button, Nano USIM slot)
Tips for Users on a distance from this product in use
Press a latch to separate the cable.
Memo
MSIP-CRM-MDJ-KMR200
USBport
MicroUSBport
Direction of USB cable
connection
YYMMDD
1234567
123456789012345
ktEgg_123
moda12345
Memo
Memo
Memo
Memo
※“xxx” refers to the terminal number or the unique number
of English characters .
※External battery power function is only active when
power on or power saving mode.
Memo
Tips for Users on SAR (Specific Absorption Rate)
Model KMR200
Dimension 113.6 × 24.7 × 27.5mm
Weight 84g
Battery Capacity 3100mAh
Time for Continuous Use 12 Hours in Max.
Certified No. MSIP-CRM-MDJ-KMR200
Description of Device Wireless Device for LTE Mobile Communication
(Transmitter/Receiver of Land Mobile Station)
Company for Conformance Test MODA Information & Communications Co. Ltd.
Manufacturer / Country of Origin MODA Information & Communications Co. Ltd. /
South Korea
Manufactured Date Separately marked on product label
- This product was designed as a general home appliance. Do not use this
product in applications that requires high reliability (communication devices
of service providers or computer devices)or are related to human life.
This may cause huge social mess as well as death or serious injury.
- Do not handle the product with wet hands. It may be a cause of electric shock.
- Please abstain from using this product in case there are medical devices and
follow the instructions of the medical institutes for prohibited places to use or
to carry the product.
- Please turn off this product in the places where the wireless devices are restricted
to use such as planes or hospitals. It may be a cause of accident by influencing
the electronic devices or medical devices.
- Please turn off this product immediately if it effects the automatic control functions
of car, elevator or automatic doors. This is concerned about hindering safe driving
or safe movement of a car.
- Do not use or keep this product in high humid places like a bath room or near the
humidifier. It may be a cause of failure.
- Do not use, keep or place this product in the places with direct sun lights,
near the heating devices like stove or heater. It may be cause of failure or
deformation of the product. In addition, it may be a cause of burn due to
overheating in a part of product or of fire due to high temperature inside of product.
- Do not place the product at the places for oil spattering or steaming
such as near the cooking counter. It may be a cause of fire, electric shock or
failure of product.
- Do not put the product on the places with extreme temperature
changes like near the air conditioner and heater. It may be a cause
of fire, electric shock or failure of product.
- The temperature of this product can increase during the use or
charging and there is a chance for mild burning injury when touching
the product for long time with bare skin.
- If either sitting down or applying force when the product is within a
pocket, the product can be destroyed or damaged.
- There are chances for itching or allergy depending on personal
constitution due to paints or metals used in this product. When such
symptoms occur, immediately stop to use it and consult with a
medical doctor.
- Please keep this product 0~40℃.
- This product is subject to use in domestic and cannot be used in oversea.
- This product cannot be used out of service area.
- Signal status or transmission speed can vary depending on building
structure, materials, furniture arrangement, moving speed of user.
- If signal status becomes weak below certain level, communication can
be cut all the sudden. In addition, even in signal status is good,
communication can be cut.
- Although in service available area, the communication may be
unavailable or the speed becomes slower in the places where the
signals hardly reach such as building inside, car inside, tunnel inside,
radio shadow spot, mountainous territory. In addition, sometimes the
communication may not be established even in widely open area.
-Web Setting Screen▶WiFI Setting Menu selection
-Input the name of WiFi to be changed at
“WiFiName(SSID)”
-Input the password of WiFi to be changed at “Password”
-Click “Apply” button at the bottom
-Web Setting Screen▶Function Setting Menu selection
-Input the time wanted at “Entering Time for Power
Saving Mode” & “Power ON Time”.
-
Select a day of the week for repetition at “Repetition Setting”
.
-Click “Apply” button at the bottom
●WiFi Name (SSID) & Password change
The product automatically enters or releases the power saving
mode as predetermined schedule and user can use the
product conveniently as the usage pattern.
This product complies the standard for protecting a human body from
Electromagnetic waves. It was designed and manufactured not to
exceed 1.6W/kg of SAR in exposure of human body under max power
level for all transmission frequency bands. It had a certificate for its
conformance from the authorized organization based on the standard
mentioned above prior to commercialization.
This product was tested with a distance of 1.5m away between its rear
surface and human body through general use procedures. The standard
from the Ministry of Science, ICT and Future Planning for protecting a
human body from electromagnetic waves indicates that the distance
between a user and the rear side of portable wireless internet connection
devices should be at least 1.5m regardless of using antenna.
It is not recommended to use belt, clip, case and similar accessories
that contain the metallic parts.
Please do not use accessories that do not satisfy the standard from
the Ministry of Science, ICT and Future Planning for protecting a human
body from electromagnetic waves or do not maintain distance of
1.5m between a human body and a rear side of device.
●Reserved Power Saving
-Check power status of product
If LCD is off, turn on the product by pressing & holding
[Power(OK)] button for over 3 seconds.
If no battery remains, turn on the product after fully charging it.
-Check signal strength through LCD
If the signal strength shows “x(refer to the image above)”,
this indicates the current location has no LTE signal and
no LTE connection is available. Please move immediately to
a location where LTE signal exists.
●Internet connection failure
LTE
signal
strength
WiFi
connections
Battery
Remains
USIM
status
User
Guide
Data
This product is a home appliance (B grade) certified for the EMI and is mainly used
at home although it works anywhere.
When using in my URoad App
App execution▶Loss Prevention▶Egg Loss Prevention On
When using button of the product:
-Under LCD On, press [Power Saving(Next)]
button to move to [Loss Prevention] menu
-Press [Power(OK)] button to select
[Loss Prevention] menu
-Press [Power Saving(Next)] button to move to “ON”
-Press [Power(OK)] button to select “ON”
-Verify if this function is on.
my
URoad
Loss Prevention Function OFF State
Loss Prevention Function ON State
Android
iOS
※This function is only available when Egg is power on and my URoad is installed in either smart phone or tablet.
※ In order to use the loss prevention alarm function
or the finding egg function, please turn on the egg
loss prevention function in advance as shown above.
[Initialization]
button
Data
Data
Memo
●Windows 8/10
-Click “Network Setting” on Task Bar of the right lower
area of Desktop screen as shown below.
-Open the USIM cover in main body and copy ‘KEY’
(WiFi Password) value attached on the label, then input
the value to a window “Network Security Key Input”.
-Later on, after connection is completed, execute the
Web browser to verify the internet connection.
-Select [ktEgg_xxx] from
[Wireless Network Connection]
and click [Connect].
-The product can be easily carried with
bags or pouch by using a USB strap
cable.
“KEY” value on the label is the initial defined
value and please use the changed value
after changing the password of WiFi.
There are some terminals that do not support
the WiFi encryption technology (WPA-PSK/
WPA2-PSK) of this product. Please consult
with the manufacturer of terminal in case of
failure in WiFi connection even if the correct
password is entered.
Loss prevention is a feature that uses Bluetooth,
so it can only work when Bluetooth on your
smartphone is turned on.
If you run an EGG search, there may be a slight
difference from the actual distance due to radio
interference problems.
Although it allows safe communication due to
authentication or encryption technologies, there
is a still possibility for the communication to be
inspected by a 3rd party. Please make sure to
change the factory defined WiFi password.
Auto Driver installation is supported in on
only Mac OS and Windows 7 or higher version.
If a driver is not installed normally, then please
separate the product from a laptop and
re-connect to complete driver installation.
If still failure occurs in driver installation,
please check USB Tethering On in Web
setting screen or my URoad(mobile App).
(initial setting is On)
Since it can explode in case of high temperature,
never keep the product in a car, especially during
the summer.
It is recommended to use the charger or USB strap
cable supplied as accessories. Use of unauthorized
charger may be a cause of the product failure.
When using the product indoor, communication
distance can be shorter due to obstacles such as
walls.
WiFi password (wireless network KEY) of egg
is written on the label attached in USIM cover.
Connection to [Web Setting Screen] is only
available when WiFi or USB Tethering connection
is accomplished.
The changed WiFi settings are not automatically
applied and the product needs WiFi connection
again with new settings.
In order to correctly use this product,
IP address setting should be “Auto”.
When a battery remains of the product is less than 20%,
External battery power function does not work.
When charging fully discharged devices or some of
iPAD tablet devices, the product may goes power off.
Memo
Easy Share can also be set for security configuration
through [Web setting screen] or
[my URoad(mobile App)].
Please refer to [Web setting screen
(Changing Settings)]for connection procedure of
[Web setting screen].
When using the product for long time with car engine
off, it may cause complete discharge a car battery.
Please use the product with a car engine on.
9. Utilizing USB Cable Strap
10. External Battery Power Function
11. Easy Share Function
This product can be used in various ways, for instance, can be charged or can charge
other devices by connecting a USB strap cable, in addition, can be connected to
Internet via PC / Mac.
12. Procedures to Use Mobile App (my URoad)
14. Settings for Web (Changing Settings)
15. Troubleshooting
16. Precautions in Use
17. Limitations in Use
19.Other Necessary
Information
18. Product Specifications
my URoad, which is a dedicated App for this product, enables users to use this product
more conveniently through smart phones or tablets.
13. Loss Prevention Function
When a Smart Phone or a Tablet is away certain distance from Egg, my URoad(mobile App) alarms user to prevent loss of Egg,
or when a location of Egg is not identified, my URoad allows user to locate the Egg.
devices such as smart phones or tablets.
It can conveniently charge other devices
by directly connecting cable without
a gender converter.
This function simply and conveniently enables or
disables a wireless connection of another device,
which needs temporary connection, by providing
separated Guest wireless network (Easy Share SSID)
without disclosing a WiFi password.
Thanks to this function, a WiFi network owner can
use the network without altering password after
disconnecting other devices.
●Use the product by
connecting to the pouch
-The USB strap cable can be separated from a holder.
●Separating the USB strap cable
-The product can charge other devices such as
smart phones or tablets using its own USB port which is
an output of external battery.
●Use the USB strap cable as auxiliary cable
- Connect micro USB port of product to USB cable
and connect other side of the USB cable to a charger
or USB port of car charger.
- Open the USB cover in the product and connect the
cable for charging.
- Connect the opposite side of the cable to the charging
port of the other device.
- As soon as the product perceives a connection,
it automatically starts to charge.
-“Charging Status LED” lights in Red during charge in
progress and turns to Green when fully charged.
●Charging
- When using a button of the product
- When using [my URoad(mobile App)]
Execute App▶Setting▶Click the “Use Easy Share”
●Method to Use
-Connect a USB cable to a micro USB port of the product.
-Connect a USB port of the cable to a USB port of PC or Mac.
-Turn On power by pressing & holding the [Power (OK)] button.
-After booting, a driver software is installed automatically.
-After installing a driver, Internet is ready to use once the
“Network Icon” on the bottom of Desktop screen
goes to shape.
●Use USB tethering
ID/Password are required to enter during the very first connection in order to use my URoad.
In case of factory setting, initial ID is “User” and Password is “WFi password(wireless network KEY)”
value to use. After changing the ID/Password of Web setting screen, revised values must be used to connect.
- Display of SSID/App, SW version
- Display of Data Usage
- Web Setting Screen Connection
- Display of My Tariff System
●Terminal Connection Setting (ID / Password entry)
This product allows to change the settings or to
check the terminal status through Web browser
based setting screen. Since [Web Setting Screen]
is imbedded in the product, it is possible to use it
when even Internet is not available.
-Connect the terminal that executes egg and
Web setting screens through WiFi or USB Tethering
-After executing a Web browser, input [192.168.1.1]
or [my.egg] in the address window.
-Input “ID” & “Password” in the log-in window.
The factory setting of this product are “user” for ID
& “WiFi Password” for password.
●Web Setting Screen Connection
It is possible to check the Status information on the
egg such as data usage, network information,
WiFi information at a glance.
●Verification of Status Information
●Turning on Loss Prevention Function ●Setting Loss Prevention Alarm ●Finding my Egg
●my URoad offers Widget function on iOS and Android terminals so that user can check signal strength,
battery remains and data usage without executing my URoad App.
- Please select [my URoad▶Information(i)▶Display my tariff system] in order to check my tariff system.
●Functional Description (Screen)
①Information Display
- Update information displayed
on my URoad
⑦Update
- Change the product to Power Saving Mode
⑧Power Saving Mode
(Sleeping Mode)
- Power off of the product
⑨Power Off
- Auto Entering of Power Saving Mode /
Setting for reserved release time
⑩Power Saving Reservation
- Loss Prevention Alarm / Finding My Egg
⑪Loss Prevention
- Power re-booting of product
②Re-booting
- Display of Signal Strength
③Signal Strength Display
- Display of Battery Remains
④Battery Status Display
- Display of No. of Connections &
Frequency bandwidth
⑤No. of Connected
Terminals Display
- Access Account, SSID/KEY change,
Frequency Band Setting,
- Configuration to use Easy Share & ESB Tethering
⑥ Settings
Press [Power Saving(Next)] button under LCD On
state in order to move to [Easy Share] menu.
Press [Power(OK)] button to select [Easy Share] menu
Press [Power Saving(Next)] button to move to “ON”
Press [Power(OK)] button
-After checking WiFi connection status of the terminal
to use, try to establish WiFi connection again.
-After pressing “Initialization” button with sharp objects
such as a clip to force the termination, then re-start
the product.
-If Internet connection is still failure even though
performing all the measures above, please contact
the customer service of
our company(Tel: 02-3487-0700).
When problems occur in product use, some of problems
can be solved by product initialization.
-Initialization is performed by pressing “Initialization” button
located on USIM cover inside with a sharp object like a clip.
-LCD shows “Initialization in Progress” and re-start the product.
-Product returns to the state of factory settings after re-starting.
These are the precautions to safely use this product. Please follow
the instructions.
- Do not use the chargers other than the supplied with product when
charging the product.
- Do not put the product and battery into water or fire and do not disassemble or
modify the product.
- Be careful that children may not put the product and accessories into their mouse.
There is a possibility of choking.
- If there are abnormal situations such as smoking and smelling from the product,
turn off the product immediately. Continuous use can cause a fire or electric shocks.
- Do not put the product into water or have it wet. Do not have the product wet
when using it outside and turn off the product immediately in case water permeated
into the product. Continuous use can be a cause of failure in the product.
- Do not put foreign substances like metallic objects or inflammable materials into the
product. If such materials got into the product, turn off the power immediately.
Continuous use can be a cause of fire, electric shock or failure in the product.
- If the product was dropped, had strong impact or was destroyed, turn off
the power immediately. Continuous use can be a cause of failure in the product.
- Do not disassemble, modify or repair the product without
authorization since those may be a cause of failure.
●
Initialization Procedure
Data
Data
- Selection of alarm distance :
very close/ Close/ Far away/ Very far away
- If Egg is away from s smart phone farther than
predetermined distance, alarm sounds to
prevent a loss.
•[my URoad(mobile App)]▶Loss Prevention▶
Loss Prevention Alarm ON
- After verifying a distance from Egg at [my URoad App],
move to the location.
- Succeeding Egg finding
•When location of Egg is unknown, select
[my URoad]▶[Loss Prevention]▶[Finding my Egg]
Table of contents
