Kucht Professional KM30C User manual

BUILT-IN
www.kucht.com
APPLICABLE MODEL: KM30C
INSTALLATION MANUAL
BE A PRO IN YOUR KITCHEN
MICROWAVE CONVECTION OVEN

5
Before you begin Beforeyoubegin
Tools and parts needed
Philips head screwdriver
1/8" drill bit and drill
Measuring tape
Parts included
Microwave oven
Philips head screws
Power Requirements
The outlet must be properly grounded in accordance with
all applicable codes.
It can be installed in the back wall directly behind the
appliance.
You can also connect your appliance directly to a
compatible conventional Built-in Oven. Refer to separate
Combination Instructions.
Checklist for Installation
Use this checklist to verify that you have completed each
step of the installation process. This can help you avoid
mistakes.
Refer to detailed instructions for each step in the
sections following this checklist.
1. Before installing the appliance, be sure to verify the
cabinet dimensions are correct for your appliance and
that the required electrical connections are present.
Make sure the electrical conduit provided on the
appliance is able to reach to the point of connection.
Section: Dimensions and Cabinet Requirements
2. Move the appliance into place in front of the cabinet
opening.
Section: Removing Packaging
3. Remove packaging materials, leaving the bottom
packaging on the appliance to avoid damage to the
floor.
Section: Removing Packaging
4. Team-lift the appliance directly into the cabinet cutout.
Section: Install Appliance, "Mount to Cabinet”
5. Slide the appliance all the way into place.
Section: Install Appliance, "Mount to Cabinet”
6. Fasten the appliance to the cabinet opening with the
screws supplied.
Section: Install Appliance, "Mount to Cabinet”
Always read and follow the complete installation
instructions contained in this manual.
Removing Packaging
NOTICE: To prevent damage to your floor keep the unit
in its packaging base until ready to be placed in the
cabinet opening. Do not slide the unit across the flooring.
Different models use different packaging materials.
Bracket remains in packaging base.
1. Cut straps on outside of box.
2. Remove cardboard box.
3. Remove all top and side cardboard and Styrofoam
braces.
4. Place oven in front of cabinets where it is to be
installed.
NOTICE: To avoid damage to the microwave oven, do
not grip or use the door or door handle while the
microwave oven is being handled.

6
Dimensions and Cabinet Requirements
General Cabinet Requirements
Cabinet requirements vary depending on the model to be
installed. Please consult the section “Dimensions” for
the details pertaining to your particular model.
All models require:
¼" (6.4 mm) space between the side of the appliance
and an adjacent wall or cabinet door when installed at
the end of a cabinet run.
The cabinet base must be flat and capable of
supporting the weight of your appliance when in use.
See the appropriate weight for your model in the
Dimensions section pertaining to your particular
model. For combination units consult the section
Cabinet Dimension Requirements in the installation
manual of your combination appliance.
The appliance door will overlap the furniture below by
approx. 3/16" (5 mm) when opened. If necessary, you
can elevate the appliance position by adding a panel
in the required thickness on top of the supporting
base. The supporting base must be level and securely
fixed to the cabinet.
Outlet Area
Anywhere within the shaded area the minimal distance
between the appliance and the wall is 1¾ in (45 mm).
Appliances with plug connection: The outlet can be
located anywhere within the shaded area.
Appliances with wire conduit connection:
For stand alone installation, the electrical connection
box must be mounted to the wall inside the cabinet
cavity anywhere within the shaded area.
For installation as part of a combination of various
Bosch appliances, please consult the installation
manual of the combo-unit.
Dimensions for 30" Wall-Mounted Units
Appliance Dimensions
Cabinet Dimensions
NOTICE: The cabinet base must be flat and capable of
supporting a weight of at least 142 lbs (64.1 kg).

7
Under counter dimensions 30” units
Flush installation 30" units
Flush installation also requires:
two side cleats to be attached inside the cabinet
frame, recessed from the front
a 5/16 " (8 mm) baseplate underneath the unit body.

8
Electrical Installation
The model stated on the front cover is rated at 120V AC,
60 Hz and uses a NEMA 5-20 plug to connect to a
dedicated 120 V microwave circuit.
Electrical Requirements:
a three prong grounded outlet
120 V, 60 Hz, AC only
15 Amp electrical supply with a fuse or a circuit
breaker
This product must be connected to a supply circuit of the
proper voltage and frequency. Wire size must conform to
the requirements of the National Electric Code or the
prevailing local code for this rating. The power supply
cord and plug should be brought to a separate 20-amp
branch circuit single grounded outlet. The outlet box
should be located in the area behind the appliance (see
section Cabinet Dimensions ). The outlet box and supply
circuit should be installed by a qualified electrician and
conform to the National Electrical Code or the prevailing
local code.
The voltage used must be the same as specified on the
data plate of this microwave oven. Using a higher voltage
is dangerous and may result in a fire or oven damage.
Using a lower voltage will cause slow cooking. The
manufacturer is not responsible for any damages
resulting from the use of the oven with any voltage other
than specified.
Install Appliance
Note: The appliance is heavy. It is advisable to install it
with a second person.
NOTICE: Before installing the appliance, be sure to
verify the cabinet dimensions and electrical connections.
Mount to Cabinet
1. Fully insert the appliance and center it. Do not kink the
electrical cable.
2. Screw the appliance into place.

FOR MORE DETAILS AND INFORMATION, PLEASE VISIT OUR WEBSITE WWW.KUCHT.COM
WE TRANSFORM A SIMPLE KITCHEN INTO A PRO ONE.
THIS IS WHY WE CARE ABOUT MAKING VERY HIGH PERFORMANCE
RANGES AND HOODS, TO MAKE YOU FEEL LIKE A PRO AND STYLISH COOKER.
DESIGN: LONDON DC - WWW.LONDON-DC.COM