KYL GSM/GPRS/GPS Tracker User manual

Shenzhen KYL Communication Equipment Co., Ltd
www.rf-data.com Fax: [phone] [email protected]
1
GSM/GPRS/GPS Tracker
User Manual
Preface
Thank you for purchasing this product. This manual shows how to operate the device smoothly and
correctly. Make sure to read this manual carefully before using this product. Please note that
specification and information are subject to change without prior notice in this manual. Any change
will be integrated in the latest release. The manufacturer assumes no responsibility for any errors or
omissions in this document.

Shenzhen KYL Communication Equipment Co., Ltd
www.rf-data.com Fax: [phone] [email protected]
2
Content
1. Summary………………………………...……………………...…………………2
2. Application………………………………………………………...………………2
3. Hardware description………………………………………...……………….......2
4. Specifications………………………………………………………………………4
5. How to use.....…………………………………………………………...…………4
6. Cautions…………………………………………………………………………..13
7. Faults & Solutions……………………………………………………...………..14
1 Summary
This device works based on existing GSM/GPRS network and GPS satellites. It
can be used to locate and monitor any remote targets by SMS or internet.
2 Applications
●Vehicle rental / Fleet management etc
●Protect child / the old / the disabled / pet etc
●Provide peace-of-mind for businessmen
●Manage personnel
●Track criminals secretly

Shenzhen KYL Communication Equipment Co., Ltd
www.rf-data.com Fax: [phone] [email protected]
3
3 Hardware Descriptions
3.1
Front face
3.2 Rear
face
3.3 Side face
3.4 Bottom face
3.5
Interior
GSM/GPRS antenna is inside
Put SIM card here.
Indicator for power
Indicator for signal
SOS Button
Turn on/off button
Press this button and
push the cover to the
right side. Then you
can open it.
Charge jack

Shenzhen KYL Communication Equipment Co., Ltd
www.rf-data.com Fax: [phone] [email protected]
4
4 Specifications
Content Specifications.
Dim. 78.4mm x 45.4 mm x 16.5mm
Weight 40g
Network GSM/GPRS
Band 900/1800/1900Mhz or 850/900/1800/1900Mhz
GPS chip SiRF III chip
GSM/GPRS
module SIMCOM 300 OR SIMCOM 340
GPS sensitivity -159dBm
GPS accuracy 5m
Time To First Fix
Reacquisition 0.1s
Cold status 45s
Warm status 35s
Hot status 1s
Car charger 12—24V input
5V output
Wall charger 110－220V input
5V output
Battery Chargeable changeable 3.7V 1100mAh Li-ion battery
Standby 72hours
Storage Temp. -40°C to +85°C
Operation Temp. -20°C to +55°C
Humidity 5%--95% non-condensing
5 How to Use
5.1 SIM card installation
Make sure there is no call transfer and call display on, and keep PIN code off.
The message must be in Text format, can’t be identified by PDU format.
Steps:
1 Open the rear cover, and take out the battery.
2 Put up the foil Push the foil to the
left side. Then you
can open it.

Shenzhen KYL Communication Equipment Co., Ltd
www.rf-data.com Fax: [phone] [email protected]
5
3 Insert SIM card into the holder, put down the foil right and fasten it.
5.2 Battery and Charger
Please use the original battery and charger provided by the manufacturer. This
device adopts built-in Li-ion battery, and full battery will support around 60 hours.
Do charge the battery up 8 -12 hours for your first use. After first use, the battery
can be charged fully in 3-5 hours.
Cautions:
a. For its Li-ion battery, which contains harmful chemicals and may burst, please
keep it off fire and don’t bump, puncture it violently.
b. Please charge the battery in time to keep it working normally.
5.3 Startup
●Put the SIM card and battery in its place. When the device is on, you can see
the red indicator is on for about one minute. If you press the red button for a
while, you will switch it off.
●The red button near “SOS” button is the “on/off” button.
●For first use, please initialize the device and restore it to default setting. (go to
5.4 for instruction.)
●There are three indicators on the device.
1. The blue indicator (on the left) shows the status of GPS. When it blinks

Shenzhen KYL Communication Equipment Co., Ltd
www.rf-data.com Fax: [phone] [email protected]
6
every two seconds, the GPS is standby. When the blue indicator is off, the
tracker is working but doesn’t get position yet. If the tracker gets the
position, the blue indicator will be on all the time.
2. The blue indicator (in the middle) is the charge led. The indicator blinks
means the device is on charge. After the device is full of electricity, the
indicator will be on all the time.
3. The red indicator (on the right) represents GSM working status. Red
indicator blinks, GSM is working. If you want to test the device, please
put it outside of the window.
●Test this device by a mobile phone:
When the device receives GPS signals and GPS position normally, you
can use it and do all the following settings.
5.4 Initialization
Send “begin+password” in SMS to the device, it will reply “begin ok” and
initialize all the settings. (Default password: 123456)
5.5 Quick set up
5. 5. 1 Test device by mobile phone:
1. Send SMS “telephone123456” to the number (the SIM card number which
you insert into the device). A message “set telephone ok.” will be sent back
to your mobile phone.
2. Send SMS “tracker123456” to the device. The same, a message “tracker
ok” will be sent back.
3. Two ways to test the device.
a. Call the number (the SIM card number in the device), the device will cut

Shenzhen KYL Communication Equipment Co., Ltd
www.rf-data.com Fax: [phone] [email protected]
7
off by itself and begin to search the position. One minute later, no
matter whether it has fixed position, the device will send back a
message. If the device hasn’t fixed position, it will keep searching for 4
minutes. During those 4 minutes, the device will send message back if
it has fixed position. If not, it will not send message back.
b．Send SMS “at30sum0” to the device. You will get messages every 30
seconds. (The data sent back to you every time may be a little different,
but it is ok, some error is permitted.) Cancel this function, please Send
SMS “noat+password” to delete the auto track. For example
password is 123456: Send SMS “noat123456”.
5. 5. 2 Test the device by GPRS Online platform:
For example, send the following SMS to set track platform.
1. Send SMS: apn123456+space+apn code to the device No. The device
will reply SMS ‘Set APN ok’. (Please note, different countries with
different apn codes)
2. Send SMS: number13412345678 to the device No. the track
platform number would be have 11 digits. It will reply ‘set number ok’.
(Please note, 13412345678 is SIM number you put in device)
3. Send SMS: IP119.147.23.100PORT2332 to the device No. The device
will reply ‘set IP address and PORT ok’. (Please note, 119.147.23.100 is
the IP of your own server, 2332 is the port of your own server)
4. Send SMS: web123456 to the device No., the device will reply ‘set
web ok
5. Send interval SMS: at30sum0 to the device No. The device will reply

Shenzhen KYL Communication Equipment Co., Ltd
www.rf-data.com Fax: [phone] [email protected]
8
"Auto track set ok.” ‘AT30SUM0’ means device replies the location
intervals every 30 seconds. (Please note, 0 means detail times)
5. 5. 3 Monitor the voice of the device.
Send SMS: monitor123456 to the device No. The device reply ‘monitor
ok’, then you can monitor the voice.
Attention: In the model of Monitor, you can not get the location by call
it, but you can send ‘position’to get the location.
5.6 Change password
Send SMS “password + old password + space + new password” to change the
password. Password only has SIX digits in all.
For example password is 123456: Send SMS:’Password123456 168168’
Remark: Be sure to keep the new password in mind, if you forget your password,
you can send SMS ‘resumepassword’to resume the default password.
5.7 Authorization
There are only 4 numbers able to be authorized.
a. Call the tracker for 10 times, it will make the cell phone number as the
authorized number automatically. You will receive SMS ‘you are
administrator’
b. Send SMS ‘admin+password+space+cell phone number’to set up an
authorized number. The other authorized numbers should be set by the first
authorized number. If the number is successfully authorized, the device will
reply “admin ok!” in SMS.
For example password is 123456: Send SMS:’admin123456 13642345678’
c. Send SMS ‘noadmin+password+space+authorized’ number to delete the

Shenzhen KYL Communication Equipment Co., Ltd
www.rf-data.com Fax: [phone] [email protected]
9
authorized number. If the setting is successfully, the device will reply “no
administrator state” in SMS.
For example:’noadmin123456 13612345678’
d. If you are in a foreign country to set up your device, you should add the
country code which your SIM card belongs to before the cell phone number.
For example password is 123456: Send SMS:’admin123456 0011231231234’
5.8 Real-time polling
a. If there is no authorized number, when any number dials up the device, it will
report a Geo-info; If there is already an authorized number, then it will not
respond when an unauthorized number calls it up.
b. When an authorized number dials up the device, it will hang up and report a
real-time Geo-info as below:
c. When there is no GPS signal fixed, dialing up the device, it will reply the last
fixed location as below:
5.9 Auto Track

Shenzhen KYL Communication Equipment Co., Ltd
www.rf-data.com Fax: [phone] [email protected]
10
Report a Geo-info at 30s (minute: m; hour: h) intervals to the authorized numbers
for 5 times:
a. Set up: Send SMS ‘at30sum15’ to the device, it will report the Geo-info at 30s
intervals for 15 times. (s: second, m: minute, h: hour). The setting must be in
5 digits and at maximum 65535 in value.
b. Send SMS ‘at60sum0’to the device, it will reply SMS heaps of times
c. Cancel: Send SMS ‘noat+password’ to delete the auto track .For example For
example password is 123456: Send SMS’noat123456’
5.10 Voice Surveillance
In this mode, the user can dial up the device to monitor the voice (please refer
to 5.9 for instruction).
5.11 Modes switch between “track” and “monitor”
a. The default mode is “track”.
b. Send SMS ‘monitor+password’ to the device, and it will reply “monitor
ok!” and switch to “monitor”mode. For example password is123456, Send
SMS:’monitor123456’
c. Send SMS ‘tracker+password’ to the device, it will reply “tracker ok!” and
restore to “track” mode. For example password is 123456: Send
SMS ’tracker123456’
5.12 Geo-fence
Set up a geo-fence for the device to restrict its movements within a district. The
device will send message to the authorized numbers when it breaches the
district.