L SHAPE CRD-8400B User manual

CD-ROM DRIVE
MODEL : CRD-8400B/CRD-8400C
OWNER’S MANUAL
BEDIENUNGSHANDBUCH
MODE D’EMPLOI
MANUALE D’USO
MANUAL DE USUARIO
To enjoy fully all the features and functions of your CD-ROM Drive,
Please read this Owner’s Manual carefully and completely.
CRD-8400B/CRD-8400C CD-ROM DRIVE
E
N
H
A
N
C
E
D
English.......Page E-2 ~ E-14
Deutsch.....Seite D-1 ~ D-13
Français.....Page F-1 ~ F-13
Italiano..........Page I-1 ~ I-13
Spanish......Página S-1 ~ S-13
English.......Page E-2 ~ E-14
Deutsch.....Seite D-1 ~ D-13
Français.....Page F-1 ~ F-13
Italiano..........Page I-1 ~ I-13
Spanish......Página S-1 ~ S-13
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
Copyright©1997 LG Electronics Inc.
LG Electronics USA, Inc.
1000 Sylvan Ave.
Englewood Cliffs, NJ 07632
LG Electronics U. K. Ltd,
LG House,
264 Bath Road,
Slough,
Berks. SL1 4DT
LG Electronics Deutschland GmbH
Jakob Kaiser Straße 12
47877 Willich 1
GERMANY
LG Goldstar France SARL
12, RUE LECH WALESA BAT.B
77322 LOGNES MARNE LA
VALLEE CEDEX 2 FRANCH
P/NO : 3828HM1013E Printed in Korea
(M-D)
CH01

E-2
This unit uses CD-ROM discs
marked with this symbol:
COMPACT
PRODUCT COMPLIES WITH DHHS
RULES 21 C.F.R. SUB-CHAPTER J,
IN EFFECT AT THE DATE OF MANUFACTURE.
WARNING: To reduce the risk of fire or electric shock,
do not expose this appliance to rain or moisture.
Industry Canada requirement
This class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel
brouilleur du Canada.
FCC COMPLIANCE STATEMENT
Note : This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a res-
idential installation. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a partic-
ular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to cor-
rect the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an Authorized Service Center for help.
• FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
• This CD-ROM Drive is for use only with UL listed personal computers that have installation instruc-
tions detailing user installation of card cage accessory.
CAUTION: The laser used in the CD-ROM drive can damage your eyes.
Do not attempt to open the cover.
To reduce the risk of electric shock, do not remove cover (or back).
No user-serviceable parts inside.
Refer servicing to qualified service personnel.
Use of controls or performance of procedures other than those specified herein may result in hazardous radi-
ation exposure.
English

E-3
FEATURES
FEATURES
■E-IDE interface
■75ms Random access time
■Multimedia PC compatible
■Photo CD multisession support
■Small CPU bandwidth (MPC spec.)
■40X-speed Max 6000KB/sec data transfer rate
■Intelligent 128KB data buffering system
■Horizontal/Vertical mounting support
■Tray Loading system without caddy
■Designed for internal mounting
■Emergency Eject Support
■Easy audio CD control button support
■Supports Windows 95 Plug and Play ATAPI protocol
SYSTEM REQUIREMENTS
An IBM PC or compatible with the following system components:
■IBM Compatible 486SX or above
(With PIO mode 4 support recommended)
■A Minimum of 640K memory
■Floppy disk drive (3 1/2inch)
■MS-DOS version 3.1 or greater
■An open, front-facing, half-height drive bay.
■An existing IDE controller in your PC with an available cable connector or a new
IDE controller that you will install.
SUPPLIED ACCESSORIES
Item
Owner’s Manual
Setup diskette
Audio Cable
Quantity
1
1
1

E-4
LOCATION AND FUNCTION OF CONTROLS
FRONT VIEW
1 Headphone Jack
3.5mm jack for monitoring the audio signal from audio CDs.
2 Headphone Volume Control
Adjusts the headphone sound level.
3 Disc Drawer
Accepts a CD-ROM disc on its tray.
4 Busy Indicator
The Busy Indicator lights during initialization and data-read operations.
5 Emergency Eject Hole
Insert a paper clip here to eject the drawer manually or when there is no power.
6 Play/Skip Button
When an Audio CD is in the Disc Drawer, pressing this button will start playing
audio CDs from the first track. If an audio CD is playing, pressing this button will
skip to the next track.
7 Open/Close/Stop Button
This button is pressed to open or close the CD tray.
If an audio CD is playing, pressing this button will stop it, and pressing it again
will open the tray.
COMPACT
1254 6 73
Figure 1. Front View

E-5
BACK VIEW
1 Digital Audio Output Connector
This is a digital audio output connector or Video CD output connector.
You can connect this to the digital audio system or Video CD Board.
2 Analog Audio Output Connector
The Audio Output Connector connects to a sound card.
The supplied audio cable is a SoundBlaster®type cable. If you have a different
sound card, you will need to contact the sound card manufacturer to obtain the
proper cable for that card.
3 Master / Slave / CSEL Jumper
These three jumpers are used to set the CD-ROM Drive to either a Master,
Slave, or CSEL drive.
Refer to section HARDWARE INSTALLATION.
4 Interface Connector
This 40-pin connector is used to transfer and control signals between the
CD-ROM Drive and your PC.
Connect the 40-pin IDE cable in your PC to this connector.
5 Power-in Connector
Attach a power cable from the computer to this connector.
Figure 2. Back View
DIGITAL ANALOG
INTERFACE POWER
DR CSM
SLA
GLG39 1+5 +12
GND
40 2
AUDIO AUDIO
125
4
3