Labgear THOR 28016T User manual

WARNING
2
1
Wall Mount & VESA Compatibility
• VESA is the standard adopted by most TV manufacturers
for wall bracket mounting.
• There are 4 holes on the back of every flat screen TV and the space
between the holes is governed by the VESA standard.
• VESA comes in a range of sizes depending on the weight and size of the flat
screen TV; sizes 50 x 50mm, 75 x 75mm, 100 x 100mm, 200 x 100mm and
so on... are standard. Not all flat screen TVs are compliant, contact the TV
manufacturer for assistance if your TV does not appear to comply with
VESA.
• To check if your TV or monitor is compliant, look at the rear of the display
there should be 4 screw/bolt holes in a square pattern or in larger displays
a rectangular shape.
• Measure the distances marked (2) (horizontal) x (1) (vertical)
below in mm to find your VESA format.
• We have not supplied wall fixings
with this product. All walls differ
in strength and thickness.
Consult a qualified installer or seek advice
from your local DIY/hardware store on
purchasing suitable wall fixings to safely
mount the bracket on the type of wall being
used.
• Check the components list and images to
check there are no missing or defective
parts.
• Never exceed the Maximum
Weight Capacity.
• Read these instructions carefully
before installation. If in any doubt about
safely installing this product, contact a
professional installer for assistance.
• This product was designed to be installed
on wood stud walls and solid concrete/
brick walls. When fixing to
walls screws/bolts should be fixed into
bricks/stone not into mortar courses.
• Make sure the wall will support the
combined load of the equipment and
hardware. Also check for hidden
wiring or plumbing.
• Make sure that the heads of the screws/
bolts you buy as wall fastenings are the
correct size to hold the bracket securely in
position.
• Always ensure that all 4 bolts engage well
into the VESA threaded apertures on the back
of your TV; to at least a depth of 70%
of the total depth of the aperture to ensure
your TV is attached securely to the TV mount.
• For larger/heavier TVs we recommend that
you ask someone to assist you with lifting
and positioning your TV.
• This product is suitable for indoor use only.
• Improper installation or use of this product
can result in product failure, damage or
personal injury.
• This product contains small items that
could cause choking if swallowed, so keep
these items away from children and pets.
• Appropriate safety equipment and
proper tools must be used for installation.
Always check manufacturer’s operating and
safety instructions before using tools and
other equipment .
UK Distributor: Philex Electronic Ltd.,
London Road, Bedford, MK42 0NX, U.K.
EU Distributor: Philex Electronic Ireland Ltd.,
Robwyn House, Corrintra, Castleblayney,
Co. Monaghan, A75 YX76, Ireland.
© Philex Electronic Ltd. 2021. Vb1.3
USER GUIDE - 28016T
37-80"
Full Motion Heavy Duty Wall Mount
• TV Size range: 37-80"
• Maximum weight capacity: 70kg
• Mount function: Tilts +2/-15 Swivels +90/-90
• Wall to TV distance: 70-800mm
• Compatible with VESA sizes:
200 x 100, 200 x 200, 300 x 200, 300 x 300,
400 x 200, 400 x 300, 400 x 400, 600 x 400
(x7)
F
(x1)
A(x1)
B
(x2)
D
(x2)
C
(x1)
G(x1) H
(x7)
E
Components
Before installation check that you have all the components shown here and
that none of them are damaged.
(x4)
N(x8) O(x8) P
M
M8 x 30 (x4)
KM8 x 50 (x4)
L
M5 x14 (x4) M6x14 (x4)
I
M6x30 (x4)
J
M-A
M-G
M-F
M-EM-DM-C
M-B
M-H

1a. Preparing Wall Fixings - Stud Walls
Tools required
1b. Preparing Wall Fixings - Concrete/Brick Walls
B
2. Removing the VESA TV Bracket from the TV Mount
G
4. Fixing the Back Plate of the Mount to the Wall Plate
5. Attaching the Wall Plate Covers
6. Attaching the VESA Bracket to the Television
7. Attaching the Television and VESA Bracket to the TV Mount
Technical Support:
www.philex.com/support
B
3. Positioning the Back Plate of the TV Mount on the Wall Plate
FE
D
H
8. Adjusting the Tilt & Swivel
C
I J
K
O
L
P
M
N
N
N
N
O
P
Fig.1
Fig.3
Fig.4
Fig.5
Fig.6
The wall bracket Ais attached to the wall
using four appropriate screws/bolts as
shown in Fig.3. Make sure the screws/bolts
are suitable for wood and large enough to
support the weight of the TV and bracket
(if in doubt ask for advice at your local
DIY/hardware store and remember to make
sure that the heads of the screws/bolts are
the correct size to hold the bracket securely
in position).
Mark and drill four holes into the wood as close as
possible to the centre of the upright (you can use a stud detector to
find stud positions). To mark the holes, hold the bracket A
to the wall, using a spirit level to make sure the bracket
is level, and mark the centre of each hole, see Fig.1.
Drill the four holes and attach the bracket Ato the wall
using the appropriate screws/bolts.
Fig.2
The process is the same as for attaching
to wood see Fig.6. You will however need to
use suitable screws/bolts/wall plugs
for the type of wall you are mounting
onto and for the weight of your TV and
bracket (if in doubt ask for advice at your
local DIY/hardware store and remember
to make sure that the heads of the
screws/bolts are the correct size to
hold the bracket securely in position).
When fixing to walls, screws/bolts
should be fixed into bricks/stone
not into mortar courses.
Lift the TV mount and
hook it onto the top rail
of the wall plate align
the holes of the
back plate with the
holes on the wall plate
in position a, bor c
as preferred.
Select the centre
position b. if you are
unsure.
Slide the threaded retaining
brackets Dinto the
groove of the back plate
top and bottom aligning
the holes in the brackets
with the holes in the
wall plate and back plate
as shown.
Push the bolts Ethrough
the washers F, the wall
plate and back plate
and screw them into the
threaded holes in the
retaining brackets D
using the Allen key H
provided.
Select the correct size bolts
to fit the VESA holes for
your TV I/J/K/L/M.
Attach the VESA bracket
to the back of the TV by
lining up the VESA holes and
using bolts I/J/K/L/M
the washers Nand the
spacers Oand or P
(if the bolts are too long or
the TV has a curved surface)
to fix the TV securely
to the adaptor brackets.
N.B. Always ensure that all
4 bolts engage well into the
VESA threaded apertures on
the back of your TV.
To o S ho rt
To o l ong
(≥70% of depth)
Loosen the nuts holding
the VESA TV bracket to the
TV mount. unscrew the
bottom nuts.
Lift and remove the VESA bracket
as shown, keep the bottom
nuts in a safe place.
Engage the top nuts left on the VESA
bracket with the slots on the TV mount
and replace the bottom nuts then tighten
all four nutsas shown.
Clip the top and bottom wall
plate covers Conto the wall
plate.
Press down the tilt lever
to adjust the angle ot tilt.
When the angle is as
you want it pull up the
tilt lever to lock the
screen in position.