LAMAX eTiger ATV50S BLUE User manual

eTiger ATV50S
EN – USER MANUAL
DE – BENUTZERHANDBUCH
CS – UŽIVATELSKÁ PŘÍRUČKA
SK – POUŽÍVATEĽSKÁ PRÍRUČKA
PL – INSTRUKCJA OBSŁUGI
HU – FELHASZNÁLÓI KÉZIKÖNYV
SLO – UPORABNIŠKI PRIROČNIK
HR – PRIRUČNIK ZA KORISNIKA
BLUE / ORANGE

CZCZ
EN: Electric Quad – TYPE I – CATEGORY Y10+
DE: Elektro-Quad – TYP I – KATEGORIEN Y10+
CZ: Elektročtyřkolka – TYP I – KATEGORIE Y10+
SK: Elektroštvorkolka – TYP I – KATEGORIE Y10+
PL: Quad elektryczny – TYP I – KATEGORIE Y10+
HU: Elektromos gyerek quad – TÍPUS I – KATEGORIE Y10+
SLO: Električni štirikolesnik – TIP I – KATEGORIJE Y10+
HR: Električni četverokotač – TIP I – KATEGORIJA Y10+

10 11 12
7 8 9
4 5 6
1 2 3
EN Visual reference DE Bildanhang CS Obrazová příloha SK Obrazová príloha
PL Załącznik rysunkowy HU Képes melléklet SLO Slikovna priloga HR Slikovni
prilog

CZCZ
13 14 15
16 17 18
19 20 21
25 26
22 23 24

WARNING!
The device is delivered disassembled. Assembly is required for full functionality. We recommend that this be
handled by the manufacturer's professional service. Improperly performed assembly or repair may lead to da-
mage to the device that will not be covered by the manufacturer's warranty, and in the worst case, to injury or
even death. Neither the manufacturer, importer nor distributor shall be held liable for improperly performed
installation or damage caused by such installation.
WARNUNG!
Das Gerät wird aufgeklappt geliefert. Für die volle Funktionalität ist eine Montage erforderlich. Wir empfehlen,
dies dem professionellen Service des Herstellers zu überlassen. Eine unsachgemäß durchgeführte Montage
oder Reparatur kann zu Schäden am Gerät führen, die nicht durch die Herstellergarantie abgedeckt sind, und
im schlimmsten Fall zu Verletzungen oder sogar zum Tod führen. Weder der Hersteller, der Importeur noch der
Händler können für eine unsachgemäß durchgeführte Montage oder für Schäden, die durch eine solche Mont-
age verursacht werden, haftbar gemacht werden.
VÝSTRAHA!
Zařízení je dodáváno v rozloženém stavu. Pro jeho plnou funkčnost je třeba provést montáž. Tuto doporuču-
jeme svěřit odbornému servisu výrobce. Neodborně provedená montáž či oprava mohou vést k poškození za-
řízení, které nebude uznáno na záruku výrobce, v nejhorším případě potom ke zdravotní újmě nebo dokonce
smrti. Výrobce, dovozce ani distributor nenesou žádnou odpovědnost za neodborně provedenou montáž či
škody touto montáží způsobené.
VÝSTRAHA!
Zariadenie sa dodáva v rozloženom stave. Pre plnú funkčnosť je potrebná montáž. Odporúčame to zveriť odbor-
nému servisu výrobcu. Nesprávne vykonaná montáž alebo oprava môže viesť k poškodeniu zariadenia, na ktoré
sa nevzťahuje záruka výrobcu, a v najhoršom prípade k zraneniu alebo dokonca k smrti. Výrobca, dovozca ani
distribútor nenesú zodpovednosť za nesprávne vykonanú montáž alebo škody spôsobené takouto montážou.
OSTRZEŻENIE!
Urządzenie dostarczane jest w stanie rozłożonym. Do pełnej funkcjonalności wymagany jest montaż. Zalecamy,
aby powierzyć go profesjonalnemu serwisowi producenta. Nieprawidłowo przeprowadzony montaż lub napra-
wa może doprowadzić do uszkodzenia sprzętu, które nie będzie objęte gwarancją producenta, a w najgorszym
przypadku do urazów, a nawet śmierci. Producent, importer ani dystrybutor nie ponoszą odpowiedzialności za
nieprawidłowo wykonany montaż lub szkody powstałe w wyniku takiego montażu.
FIGYELEM!
A készüléket kibontva szállítjuk. A teljes funkcionalitáshoz összeszerelés szükséges. Javasoljuk, hogy ezt bízza
a gyártó szakszervizére. A nem megfelelően elvégzett összeszerelés vagy javítás a készülékben olyan károkat
okozhat, amelyekre a gyártó garanciája nem terjed ki, legrosszabb esetben pedig sérülést vagy akár halált is
okozhat. Sem a gyártó, sem az importőr, sem a forgalmazó nem vállal felelősséget a nem megfelelően elvégzett
szerelésért vagy az ilyen szerelés által okozott károkért.
SVARILO!
Naprava je dobavljena v nespremenjenem stanju. Za popolno funkcionalnost je potrebna montaža. Priporo-
čamo, da to zaupate proizvajalčevemu strokovnemu servisu. Nepravilno izvedena montaža ali popravilo lahko
privede do poškodb naprave, ki jih proizvajalčeva garancija ne krije, v najslabšem primeru pa do poškodb ali
celo smrti. Niti proizvajalec, niti uvoznik ali distributer ne odgovarjajo za nepravilno izvedeno montažo ali ško-
do, ki jo povzroči takšna montaža.
UPOZORENJE!
Uređaj se isporučuje u rastavljenom stanju. Za punu funkcionalnost potrebno ga je sastaviti. Preporučamo da
to povjerite stručnoj službi proizvođača. Nepravilna montaža ili popravak može dovesti do oštećenja uređaja,
koje neće biti pokriveno jamstvom proizvođača, ili u najgorem slučaju do oštećenja zdravlja ili čak smrti. Pro-
izvođač, uvoznik i distributer ne snose nikakvu odgovornost za nepravilnu montažu ili štetu uzrokovanu ovom
montažom.

1 1
ENCSCSCZCZCZCZCZ
CONTENTS
SAFETY SYMBOLS ............................................................................................................................................. 2
SPECIFICATIONS................................................................................................................................................ 3
PRODUCT DESCRIPTION................................................................................................................................. 4
CONDITIONS OF USE........................................................................................................................................ 5
WHERE AND HOW NOT TO RIDE ............................................................................................................................ 6
TRAINING.................................................................................................................................................................... 6
SAFETY INSTRUCTIONS................................................................................................................................... 7
RIDER ........................................................................................................................................................................... 7
PROPER CLOTHING, PROTECTIVE EQUIPMENT AND GEAR.............................................................................. 7
BATTERY CHARGING................................................................................................................................................. 7
BATTERY– SAFETY GUIDELINES ............................................................................................................................. 8
INSPECTION, MAINTENANCE AND STORAGE ..................................................................................................... 9
SAFETY GUIDELINES AND PRECAUTIONS............................................................................................................ 9
ADDITIONAL INFORMATION ................................................................................................................................10
WARRANTY REPAIRS ..............................................................................................................................................10
PREVENTION AND FIRST AID ................................................................................................................................ 11
RESIDUAL RISKS .............................................................................................................................................. 11
UNPACKING ...................................................................................................................................................... 12
ASSEMBLY......................................................................................................................................................... 12
CHECKS BEFORE RIDING............................................................................................................................... 13
CONTROLS ........................................................................................................................................................ 14
OPERATION....................................................................................................................................................... 14
RIDING................................................................................................................................................................ 15
MAINTENANCE................................................................................................................................................. 15
TROUBLESHOOTING ......................................................................................................................................16
TECHNICAL AND CONSUMER INFORMATION.......................................................................................... 17
SERVICE AND SPARE PARTS.......................................................................................................................... 17
DECLARATION OF CONFORMITY................................................................................................................ 18
Technical and design changes may be made to the products based on regular changes and amen-
dments to directives, and Czech and European standards. Photos and drawings in this manual may
be illustrative only or may use images of another product. Therefore, the customer cannot make any
claims and complaints related to this manual, (especially possible deviations from the information con-
tained therein) as long as the product meets all the given certications and declarations and functions
as described in the manual and as long as the use of the product meets the intended purpose at the
time of purchase.
This manual is written to acquaint the user with the principles of operation of this product, its assembly
and installation, as well as the rules of safe use, maintenance, and storage. This manual is an integral
part of the product, so please keep it carefully for future reference.
Please read this manual carefully before operating the vehicle for the rst time!


2
ENCSCSCZCZCZCZCZ

The quad bike must be used with the utmost caution. Safety symbols and stickers on the product alert the
user to the type of danger and remind them of all the safety guidelines. The table below explains the mea-
ning of all the symbols used.
Do not remove the stickers or safety labels under any circumstances.
General warning sign
Read the operating instructions. Before use, it is necessary to read the manual thoroughly.
Do not use this device in rain or water, or leave it outside when it is raining.
Electrical voltage hazard
Do not use the quad if you are under the inuence of alcohol, drugs, or medication.
The quad bike is not intended for use on roads.
Attention hot surface! Risk of burns!
The quad bike is a single-seater only. Do not carry a passenger!
Wear protective equipment.
10+
Use from 10 years of age onwards. Children under the age of 16 must always be supervised by an
adult.
Vehicle payload
Tyre pressure
kg Weight
Device does not belong in household waste.
Class II protection
The product complies with the relevant EU standards.

2 3
ENCSCSCZCZCZCZCZ

Name LAMAX eTIGER ATV50S BLUE / ORANGE
Electric motor 1000 W
Max. load 65 kg
Dimensions 1155 × 650 × 690 mm
Speed 6 km/h; 15 km/h; 25 km/h
Charging time 8 hours
Rim size 6“
Wheel size including tyres 14“ × 4.10 – 6 / SW-683 max. loading 130 kg
Tyre pressure 170 kPa / 24 PSI
Mass 57 kg
Protection class II
Rider age 10+
Rider height 110–140 cm
Operating noise 40 dB
*The maximum range gure indicates the approximate range that can be achieved under absolutely ideal conditions
(at terrain, constant speed - no full power, no wind, correct tyre pressure, driver weight <50 kg, no payload, ambient
temperature 20 °C). In practice, the range is then primarily inuenced by the weight of the driver and other loads, the
altitude gradient to be overcome when riding, weather conditions, road conditions, driving style, frequency of starts
(e.g. at junctions), tyre condition (especially ination), battery wear and many other factors. In extreme conditions, the
range can be reduced to less than 50% of the claimed value.
Battery specications
Battery type Lead-Acid
Rated voltage 48 V
Capacity 12 Ah
Approximate charging time 6–8 hours
Operating temperature 5°C – 50 °C
Charging temperature 0°C – 40 °C
Storage temperature 5°C – 25 °C
Storage humidity 5% – 85% non-condensing
Charging adapter specications
Input voltage AC 110–240 V
Frequency 50/60 Hz
Output voltage DC 57,2 – 57,8 V
Output current 2.3–2.5 A
Output power 140 W
Average eciency in active mode 85 %
Low load eciency (10%) 80 %
Energy consumption in the no-load state <4W
Operating conditions 0 – 40 °C
The manufacturer reserves the right to all printing errors and dierences in depiction. The manufacturer
also reserves the right to make any technical changes that do not aect the basic technical parameters and
function of the quad bike without prior notice!

4
ENCSCSCZCZCZCZCZ

15
15
21
22
23
16
24
26
910
1
17 25 18
2 3
14 4
5
19
20
6
7
8
13
12
11
1) Front brake lever
2) Rear brake lever
3) Seat
4) Rear carrier
5) Back wheel
6) Footrests
7) Battery
8) Front shock absorber
9) Front arm
10) Front disc brake
11) Front wheel
12) Front bumper
13) Front light
14) Front LED light
15) Three position speed switch
16) Rear reector
17) Light switch
18) Battery status indicator
19) Twistgrip throttle
20) Ignition key
21) Motor
22) Rear disc brake
23) Chain with chain guard
24) Rear shock absorber
25) Direction switch
26) Horn
Pay special attention to the instructions highlighted below:
WARNING!Potentially dangerous situations that could have a fatal outcome (death or
serious injury) if not avoided.
PROHIBITED! Potential danger (minor or moderate injury) and/or damage to vehicle or pro-
perty if these instructions are not observed.
ATTENTION
NOTE Provides useful information.

4 5
ENCSCSCZCZCZCZCZ
ABOUT THE LAMAX ELECTRIC QUAD ETIGER ATV50
The LAMAX eTiger ATV50S electric quad bike is designed for leisure activities. It is powered by a chain-driven
electric motor that provides quiet and emission-free operation. Speed is controlled by turning the throttle
grip on the right handlebar. Next to the handle, there is a battery charge indicator. The rough tread tyres
ensure good ground clearance. Front and rear adjustable suspension ensure a comfortable ride.

CATEGORY Y10+ quad bike
–The quad is intended for recreational use by a single driver without a passenger aged 10 years and over,
with the speed limiter being set at 6 km/h. Children under the age of 16 must be supervised by an adult
at all times and must be trained in the operation of the vehicle before their rst ride. It is always the
responsibility of the supervising adult to assess the child‘s tness to operate the vehicle. Children must
understand and follow all instructions in this manual before driving.
–In the event of an apparent defect caused by transport or unpacking, notify your dealer immediately. DO
NOT OPERATE.
–Recommended rider height: 110–140 cm
WARNING!
READ THE ENTIRE INSTRUCTION MANUAL CAREFULLY! Read all instructions in the manual before
operating the vehicle. Pay particular attention to the safety instructions.
FAILURE TO FOLLOW THE INSTRUCTIONS AND SAFETY PRECAUTIONS MAY RESULT IN PRODUCT DA-
MAGE OR SERIOUS INJURY OR DEATH.
WARNING!
The quad bike may not be operated or handled by a person:
–who is not physically t enough,
–who is unable to operate the quad bike to its full extent, or who does not understand the instructions in
this manual,
–who is under 10 years of age. Persons under 16 years of age may use this quad bike only under the
constant supervision of an adult.
WARNING!
THIS QUAD BIKE IS NOT A TOY!
PROHIBITED!
All legal standards, state and local laws must be followed when using this vehicle. These may dier
in each country, region or municipality.
SPECIFIC TERMS OF USE
This quad bike is intended solely for:
–Recreational and/or commercial use by a person 10 years of age or older. Persons under the age of
16 may only use the quad bike under the supervision of an adult.
–Operation OFF public roads.
–Use that complies with the safety guidelines in this user manual.
–No other use not consistent with the intended purpose.
Any other use not in accordance with the intended purpose will void the warranty or result in the manu-
facturer‘s disclaimer of any liability.
Any unauthorised modications will void the warranty and also exclude the manufacturer‘s liability for da-
mages resulting therefrom.
Do not overload – use the quad only for the purpose for which it was designed.
This quad bike was not designed for trade, commercial or industrial use. Therefore, the manufacturer assu-
mes no liability if this product is used in these or similar conditions.

6
ENCSCSCZCZCZCZCZ
ATTENTION
Observe legal guidelines and regulations to avoid possible accidents during operation.
The user is liable for all damages caused to third parties and their property.
PROHIBITED!
Do not use the quad bike near children or pets.
NOTE
Keep this manual carefully for future reference. If you do not understand any of the instructions, contact
your dealer. If the motorcycle is passed on to another person, this instruction manual must also be passed
on to them.
DO NOT exceed the weight limit stated in the technical specications!
WARNING!
DO NOT CARRY OTHER PERSONS. THE VEHICLE IS A SINGLE-SEATER.

PROHIBITED!
DO NOT USE THE QUAD IN ROAD TRAFFIC.
–Do not use the vehicle indoors. Using the quad bike indoors risks damaging surfaces such as carpets or
oors.
–Do not ride the quad bike near stairs or swimming pools.
–Wet, slippery, uneven or rough surfaces increase the risk of accidents. Avoid surfaces such as puddles,
mud, water, snow or ice.
–Avoid the possibility of the quad bike tipping over by not riding in areas with a slope greater than 15
degrees.
–If the quad overturns, the rider can be seriously injured or even killed.
–Do not drive in reduced visibility or in the dark without the front headlights on.
–Do not use the vehicle to tow other vehicles or tow it behind other vehicles.
–No driving in heavy rain
AREA OF USE
WARNING!
NEVER OPERATE THE QUAD ON PUBLIC ROADS!
–The quad bike is intended for operation on a dry, rm, dust-free and non-slip surface.
–Before using the vehicle, check the terrain where you want to use it. Remove any objects that could catch
or knock the vehicle, such as branches, cameras, wires, toys or other similar objects. Failure to remove
these items could result in injury to the operator or bystanders, damage to the vehicle, or overturning
of the vehicle.
–Do not operate the vehicle in a potentially hazardous environment, such as near ammable substances,
ammable gases or powders. An explosion could occur, resulting in damage to the vehicle or injury re-
sulting in death.

ATTENTION
All users of this quad bike must be fully trained in use, operation, and set-up, and familiarised with prohibi-
ted activities.
–The quad bike is not intended for use by persons with reduced sensory capacity or mental impairment.
The quad bike is also not intended for use by persons with reduced mobility or insucient physical dis-
position.Pregnant women are strongly advised not to use this vehicle.

6 7
ENCSCSCZCZCZCZCZ

–Always use extra caution when driving this quad bike. Do not use this product if you are tired or under the
inuence of alcohol, drugs or narcotics.
–Before your rst ride, carefully read this instruction manual, especially the restrictions, risks and method
of use. You must be able to stop and switch o the vehicle quickly.
–Report any damaged switches to an authorised workshop immediately. Do not operate the vehicle with
such damage.
WARNING!
Driving this vehicle can be dangerous. RIDE AT YOUR OWN RISK. The manufacturer is not responsible for any
personal injury caused by improper or irresponsible use.
ATTENTION
Do not use the quad bike in the dark or in reduced visibility.
–Start the quad bike (by turning the ignition key) in an outdoor environment and in a safe place for driving.

WARNING!
Don‘t overestimate your abilities. Dangerous driving increases the risk of injury or damage to the
vehicle.
–Always place your feet on the footrests provided when riding.
–Hands, ngers and other parts of the body must always be kept a safe distance away from the drive chain,
gears, wheels and all other moving parts.Otherwise, there is a risk of injury.
–It is prohibited to use headphones or mobile phones while riding.
–Do not touch the brakes or the motor of the quad bike. Surfaces can be very hot.

ATTENTION
Safety aids and equipment are an important prerequisite for safe riding.
WARNING!
THE DRIVER MUST USE THE PRESCRIBED PROTECTIVE EQUIPMENT.
–The driver of the quad bike must always be equipped with a helmet with a protective visor.
–For greater rider safety, we recommend using protective gloves, knee, elbow and spine protectors while
riding.
–When riding the quad bike, do not wear loose clothing that could get caught in the controls or moving
parts.
–Always wear protective equipment that covers the legs, ankles and feet when riding. Riding barefoot or
in open shoes is not permitted.

WARNING!
Failure to follow these instructions may result in electric shock, re, and/or serious personal injury.
–The battery is the most important part of the quad bike. The quad bike is equipped with Lead-acid batte-
ries and these batteries have a life cycle. In order to maximise their life, it is important to take care of your
batteries regularly.
–To charge the battery, use only the original charger from the manufacturer, supplied with the quad bike.
–If the battery indicator shows low battery capacity, connect the quad bike to the charger.
–Always make sure the charging port is clean and dry before charging. If the charger is not currently co-
nnected to the quad bike, the power input must always be covered with a rubber cap to prevent dust or
other dirt from entering the input.

8
ENCSCSCZCZCZCZCZ
–Connect the power cord to the charger and then plug the charger into the outlet and make sure the light
on the charger is GREEN.
–Insert the end of the charger into the power input on the quad bike. The charger light should turn RED
- charging. When the light turns GREEN, the quad bike is fully charged. The time to full charge is approxi-
mately 6-8 hours.
–After charging the quad bike, disconnect the charger from the electrical outlet and the power cord from
the quad bike.
–Do not leave the quad bike connected to the charger longer than necessary to fully charge.
–Do not use the charger if the cable or connectors are damaged.
–If the charger or any part of it is damaged, it must be replaced with a new one. Do not use such a charger
under any circumstances. Risk of electric shock. For replacement, contact your dealer, device manufactu-
rer or authorised service.
–Never use the motorcycle while it is connected to the charger.
–Never cover the charger.
–Charge the battery in a dry place at room temperature between 5°C and 40°C.
–Never leave the quad bike charging unattended. Charging must take place under constant su-
pervision.

–Fully charge the battery before rst use.
–Charge regularly, preferably after every ride.
–Never let the battery run down completely!
–Operating temperature can aect overall battery life.
–Never connect mechanically damaged or swollen batteries to the charger. Do not use the battery in this
state at all, there is a risk of explosion.
–Do not use a damaged power adapter or charger.
–Charge at room temperature, never charge below 0°C or above 40°C.
–Take care not to drop, puncture or otherwise damage the battery. Do not repair a damaged battery.
–Do not expose the charger or battery to moisture, water, rain, snow or various sprays.
–Do not expose the battery to sunlight or place it near heat sources. Strong light or high temperatures can
damage the battery.
–Never leave batteries unattended during charging, a short circuit or accidental overcharging can cause
the release of aggressive chemicals, explosion or subsequent re!
–If the battery overheats while charging, disconnect the battery immediately.
–When charging, do not place the charger and the battery being charged on or near ammable objects.
Pay attention to curtains, carpets, tablecloths, etc.
–It is strictly forbidden to use a mobile phone or other similar devices while riding.
–Keep the battery out of the reach of children and animals.
–Never disassemble the charger or battery.
–If the battery is integrated, never disassemble the device unless otherwise specied. Any such attempt is
risky and may result in product damage and subsequent loss of warranty.
–Do not throw used or damaged batteries in the trash, re, or into heating devices, but hand them in at
hazardous waste collection points.
–If you do not comply with these policies, you assume full responsibility for any resulting damage.
–Always charge the device under constant supervision.
–If you have any suspicion of a possible ash re, if the equipment starts to smoke or catches re, notify
the re department immediately and, if possible, place the equipment in an open area and stay a safe
distance away from the equipment. Battery cells may explode as a result of combustion and leak out of
the device.
–Do not use water-based extinguishers to extinguish the device. Suitable extinguishers are snow CO2, ha-
lotron or with F-500 extinguishing agent.

8 9
ENCSCSCZCZCZCZCZ

–A quad bike needs regular inspection and maintenance just like a bicycle or a motorcycle. Always make
sure the quad bike is turned o and the power cord is disconnected before performing the following
operations.
Checking and cleaning the quad bike
–Regularly inspect the structure and tyres for damage or excessive wear. In case of excessive wear, the tyre
must be replaced. Do not use water or other liquids or cleaning agents for cleaning. Moisten a clean cloth
with clean, soapy water and apply to the frame of the quad, then rinse the cloth thoroughly and wipe
down the quad. Clean so that water does not get into the battery cover, power input, display, or tyres.
–Regularly check the tightness of all connections and screws.
–Check the front and rear shock absorbers regularly. The damper should spring and return to its original
position after pushing on the quad.
–Check the brake function before each ride. If the brake function is not sucient, it will be necessary to
shorten the cable directly at the brake. Loosen the screw that secures the cable and pull the cable so that
it is not too tight. Tighten the screw again and ne-tune the lever.
Maintenance and service
–A quad bike requires regular maintenance and regular service just like a bicycle.
–The recommended service check is at least once a year.
Quad bike storage
–Fully charge the battery before storing. If you store the quad bike for longer than two months, charge the
battery to half capacity at least once every 30 days. If this is not done, it is very likely that the device will
malfunction, and the repair will not be covered by the warranty.
–If the indoor storage temperature is below 0°, do not charge the quad bike immediately. Before charging,
you must place the quad bike in a warmer environment (5–40°C) for at least 2 hours. Store the quad bike
indoors, in a dry place and at the correct storage temperature.

–The box contains small parts that can be dangerous for children. Always store the product out of the
reach of children. The bags can cause suocation if placed on the head and the parts they contain are a
choking hazard.
–Failure to follow basic instructions and any of the following safety precautions may result in damage to
the motorcycle, loss of manufacturer‘s warranty, other property damage, serious injury and even death.
Always use only original accessories, including the battery. If incompatible accessories are used, you risk
voiding the warranty and possible damage to the device.
–Before each use, check the technical condition of the quad bike.
–Always check the brakes and tyre condition before riding. Make sure that there are no objects in the
wheel wells that interfere with riding!
–Look where you are going and perceive the road conditions, people, places, property and objects around
you.
–Operate the quad bike with consideration for pedestrians, cars and cyclists.
–Give your full attention to riding.
–It is strictly forbidden to use a mobile phone or another similar device while riding.
–Do not ride a quad bike unless it is permitted in the area.
–Always follow local ordinances and regulations.
–Do not drive in places with a large number of pedestrians.
–Do not remove the signalling elements of the quad bike, such as reective stickers or LED lighting.
–Do not remove the warning safety and technical labels from the quad. If they become damaged or illegi-
ble, contact the manufacturer who can provide you with new labels.
–Never ride in the rain.
–Do not hang bags, backpacks or other objects on the quad bike.

10
ENCSCSCZCZCZCZCZ
–Do not attempt to disassemble, repair or modify the vehicle in any way. Disassembly, modication or any
attempted repair will void the warranty and may result in damage to the unit or even injury or property
damage.
–Do not operate the vehicle under the inuence of alcohol, drugs or other addictive substances and sub-
stances aecting the ability to coordinate and react.
–Do not use the quad bike if you are tired or sleepy.
–Use your best judgement to avoid dangerous situations with your quad bike.
–Do not turn sharply, especially at high speeds.
–Do not ride in or near puddles of water, mud, sand, rocks, gravel, or on rough and uneven terrain. There is
a risk of damage to the quad bike.
–Do not drive in bad weather: snow, rain, hail, on icy roads or in extreme heat. Skidding can occur more
easily on damp or wet roads.
–Do not drive near swimming pools or other large bodies of water.
–Handle the quad bike very carefully when indoors.
–The quad bike is intended for use by one person, NEVER try to ride with two people.
–Children must only operate or otherwise handle the quad bike under the supervision of a qualied adult.
The same applies to people with reduced mobility.
–Always consider longer stopping distances at higher speeds.
–Do not exceed the maximum load capacity of the quad bike.
–Avoid driving near hazardous or ammable substances.
–In ideal conditions and with a fully charged battery, the quad bike can cover a distance of up to 20 km.
–Factors that aect the maximum range of a quad bike: terrain, rider weight, ambient temperature,
weather conditions and driving style.

–For households: The indicated symbol ( ) on the product or in the accompanying documentation me-
ans that used electrical or electronic products must not be disposed of together with municipal waste.
In order to properly dispose of the product, hand it in at designated collection points, where it will be
accepted free of charge. By disposing of this product correctly, you help preserve valuable natural resour-
ces and help prevent potential negative impacts on the environment and human health that could result
from improper waste disposal. Ask your local authority or nearest collection point for further details.
Improper disposal of this type of waste may result in nes in accordance with national regulations. Infor-
mation for users on the disposal of electrical and electronic equipment (company and business use): For
the correct disposal of electrical and electronic equipment, ask your dealer or supplier for detailed infor-
mation. Information for users to dispose of electrical and electronic equipment in other countries outside
the European Union: The above symbol (crossed-out bin) is only valid in the countries of the European
Union. For the correct disposal of electrical and electronic equipment, request detailed information from
your authorities or equipment dealer. Everything is expressed by the crossed-out bin symbol on the pro-
duct, packaging or printed materials.

–Please contact your dealer for warranty repairs. In case of technical problems and questions, please
contact your dealer who will inform you of the next steps. Observe the rules for working with electrical
equipment. The user is not authorised to disassemble the equipment or replace any of its components.
There is a risk of electric shock if the covers are opened or removed. Incorrect assembly and wiring of the
equipment also exposes you to the risk of electric shock.
–Products are guaranteed for 24 months unless otherwise stated. The warranty does not cover damage
caused by non-standard use, mechanical damage, exposure to aggressive conditions, handling contra-
ry to the manual and normal wear and tear. For more information regarding the warranty, please visit
www.elem6.com/warranty
–The battery is guaranteed for 24 months, 6 months or 300 cycles (whichever comes rst). Keep in mind
that the maximum capacity of the battery decreases over time or use. Battery life is also dependent on
how the battery is used, charged and stored. The normal warranty period does not cover a reduction in
the maximum capacity of the battery or its life cycle as this is not a defect in material.

10 11
ENCSCSCZCZCZCZCZ
–Hardware or software interference with the conguration of the device, such as interference with the
control unit, motor, battery or other controls, may void the warranty. In this case, the manufacturer is not
obliged to accept the device for warranty claim.
–The warranty period does not apply to equipment components referred to as consumables, such as bea-
rings, tyres and tubes, brake discs and pads, light bulbs, etc.
–If the equipment was sold at a reduced price, the warranty does not cover defects or interferences for
which the lower price was set.
–The manufacturer, importer or distributor shall not be liable for any damage caused by unauthorised
tampering, installation, use contrary to the user manual, normal wear and tear or overloading.
–Out-of-warranty service can be ordered from the manufacturer‘s authorised service centre.
–In order for a warranty claim to be accepted, it is assumed that the equipment has been operated in
accordance with this user manual, including operation, maintenance, cleaning and storage. Only equip-
ment that is clean, complete and has been properly packaged for shipment can be accepted for warranty
claims.

NOTE
Recommended safety equipment
–In the event of a re, use a suitable extinguisher (snow CO2, halotron, F-500 extinguisher).
–First aid kit in case of an accident.
–Mobile phone for calling emergency services.
ATTENTION
In case of injury, treat the injured person in accordance with the principles of rst aid.
–In the event of an electric shock, it is necessary more than ever to emphasise the safety and elimination
of the risk to the rescuers. The victim usually remains in contact with the electrical device (the source of
the injury) due to the convulsive contraction of the muscles caused by the electric current. In such a case,
it is necessary to rst turn o the current in any possible way. Then call the emergency services (112) or
another professional service and only then provide rst aid! It is necessary to ensure the airways are clear,
check breathing, check the pulse, place the aected person at on their back, tilt their head and pull
down their lower jaw. Initiate mouth-to-mouth resuscitation and CPR if necessary.
–If battery uid gets on your skin, wash it o quickly with soap and water. Seek medical attention if nece-
ssary.
–If battery uid gets into your eyes, ush them with clean water for several minutes. Seek medical atten-
tion immediately.

Even if the product is used according to the instructions, it is not possible to exclude all risks associated with
its operation. The following risks may occur due to the design of the product:
–Mechanical hazards such as dropping, crushing, cutting, winding, being pulled. These hazards can be
caused by rider error, misuse, mishandling of the equipment, underestimation of the situation or fatigue,
or unforeseen terrain conditions such as sloping or uneven terrain.
–Electrical hazards that can be caused by contact with live parts (direct contact) or parts that have become
live under faulty conditions (indirect contact).
–Thermal hazards which may result in burns, scalding or other injuries caused by possible contact of per-
sons with high-temperature objects or materials including heat sources.
–Hazards arising from neglect of ergonomic principles in the design of the product, such as hazards cau-
sed by poor body positioning or excessive overloading and unnatural to human hand-arm anatomy, rela-
ting to handle design, product balance, etc.
–Noise hazards which may result in hearing loss (deafness) and other physiological disturbances (e.g. loss
of balance, loss of consciousness).
–Vibration hazards that can result in vascular and neurological damage to the hands, such as Raynaud‘s
disease.

12 13
ENCSCSCZCZCZCZCZ
WARNING!
The product creates an electromagnetic eld of very weak intensity. However, this eld may interfere with
some pacemakers. To reduce the risk of serious or fatal injury, persons with pacemakers should consult their
physician and pacemaker manufacturer regarding vehicle use.

–After unpacking the product from the box, carefully inspect all parts.
–Before disposing of the packaging materials, always carefully check whether any parts of the quad bike
are left inside the packaging.
–Keep packaging components (plastic bags, clips, etc.) out of reach of children.
–If the product is damaged during unpacking or if the delivery is incomplete, contact your dealer imme-
diately.
BOX CONTENTS
–Quad bike body, handlebars and their mounts (2 upper, 2 lower, 4 screws), front and rear protective frame,
front plastic bumper, front right and left wheels, charger, 2 fuses, instruction manual, tools.
–Standard accessories are subject to change without notice.
–This product requires assembly. The vehicle must be properly assembled before use.

–We recommend assembling the quad bike with an experienced mechanic. In the case of assembling the
quad bike yourself, we recommend two people assemble it.
–Assembly takes approximately 30–40 minutes.
–The initial battery charge can take up to 12 hours.
–Do not shorten this charging time!
–Inate all 4 wheels to the appropriate pressure (170 kPa / 24 PSI).
–Unpack the quad bike from the box.
–Remove the bolts that attach the quad bike to the iron frame (images 1 and 2).
–Remove all loose parts from the packaging (quad body, front wheels, front plastic bumper, front and rear
metal frame, manual, charger, and a set of screws and tools). See images 3, 4 and 26.
HANDLEBARS
–Attach the handlebars using the black washers and four screws (images 4 and 5).
–Tighten the screws carefully.
FRONT WHEELS
–Install the front wheels and front brake disc (images 6, 7 and 8).
–Place the wheel on the axle. Pay attention to the roll of the wheel, which is indicated by an arrow on the
outside of the tire.
–Then t the brake callipers to the brake disc and tighten all the screws.
–Tighten the outer wheel bolt properly.
–Repeat the same for the left and right front wheels (images 9, 10 and 11).
FRONT PLASTIC BUMPER
–Remove the screws from the front metal structure (image 12). Use these screws to attach the front plastic
bumper (image 13).
FRONT METAL FRAME
–Unscrew the two screws from the plastic top cover (image 15).
–Attach the front metal frame to the plastic bumper (images 16 and 17).
–Attach the front metal frame to the upper plastic cover with screws (image 18).
REAR METAL FRAME
–Attach the rear metal frame to the rear of the quad bike (image 19).
–Remove the screws from the main frame and use them to attach the rear metal frame (images 20 and 21).

12 13
ENCSCSCZCZCZCZCZ
–Fit the reector (image 22).
SEAT
–Fit the seat by rst tting the front part of the seat and then pressing the rear part with one rm push
(image 23).
FUSE
–Using pliers, take the included fuse and insert it into the protective case located on the left front of the
quad bike. A short spark may occur during insertion, which is normal (images 24 and 25).
STICKERS
–If the stickers are protected by protective lms, remove the lm.
GEOMETRY
–After assembly, it is sometimes necessary to
adjust the geometry of the front axles.
–Adjust the toe-in/toe-out by turning the stee-
ring rod. Loosen both steering rod nuts (one
thread is right and the other is left). Loosen
both nuts (same side).
–Align the handlebars and turn the hexagonal
rod to set the desired wheel direction (wheel
geometry). The wheels should be slightly
diverging.
–After adjustment, carefully tighten all nuts
NOTE
Estimate the geometry adjustments. For such small recreational vehicles, precise adjustment is not critical.
BRAKE ADJUSTMENT
–Brake pressure may need to be adjusted. The brakes can be adjusted by using the extension bolts on the
Bowden cables, or by shortening or lengthening the cables directly on the brakes.
FRONT SHOCK ABSORBER ADJUSTMENT
–The stiness of the front shock springs can
be adjusted to the rider‘s weight. This can be
done by turning the nuts on the top of the
springs (see the image below). By turning the
nut clockwise, you reduce the stiness of the
shock absorber. By turning the nut counter
-clockwise, you increase the stiness of the
shock absorber.

RELEASED PARTS
–Before each ride, check that the steering and brake bolts are not loose. There must be no unusual noises,
rattling, loose or damaged components.
BRAKES
–Check the correct operation of the brakes by pressing the lever. If you nd that the quad does not brake,
you need to contact an authorised service centre.
FRAME, FORK AND HANDLEBAR
–Check for cracked joints or broken parts. If you discover any of these defects on your quad bike, contact
an authorised service centre. Do not use the quad under any circumstances!!!

14
ENCSCSCZCZCZCZCZ
TYRE PRESSURE
–Check the tyre pressure (170 kPa / 24 PSI) and the condition of the tread regularly. Always perform tyre
pressure and any ination when cold. In the event of a at tire and the need to replace the wheel rim,
contact the service department.

The quad bike is operated by using hands only.
RIGHT HANDLEBAR SIDE
–Grip / Throttle – the right grip controls the speed.
–FORWARD/REVERSE/OFF– switch to change the direction of travel.
–Right front disc brake lever – use the lever to brake the front wheel.
–Battery charge indicator – 4 bars (fully charged), 3 bars (suciently charged), 2 bars (low), 1 bar (dischar-
ged)
LEFT HANDLEBAR SIDE
–Grip
–Switch (red) – turns the front headlight on/o.
–Switch (green) – controls the horn.
–Left rear disc brake lever – use the lever to brake the rear axle.
CHARGING SOCKET
–The charging connector can be found under the cover on the left side under the handlebars.
SPEED SWITCH
–A 3-position switch with a key is located on the left side of the motor
cover. This switch can be used to adjust the maximum speed.
–L: Low speed – (6 km/h)
–M: Medium speed – (15 km/h)
–H: High speed – (25 km/h)

–Insert the key into the ignition switch located below the battery indicator on the right side of the han-
dlebars.
–Set the direction switch to the FORWARD or REVERSE position depending on which direction you want
to go.
ATTENTION
Never ip the switch while the vehicle is in motion.
–Carefully twist the accelerator (throttle) grip towards you and the quad bike will start moving.
–Stop by releasing the throttle grip.
–Use the brake levers to stop immediately – right for the front brake, and left for the rear brake.
–When the brake lever is pressed, the motor is automatically disengaged until the brake levers are
released again.
–The wheels may „throw“ slightly at higher speeds.