Larsson & Jennings SAXON AUTOMATIC User manual

SAXON AUTOMATIC

www.larssonandjennings.com/support

01
International Warranty
Watch Specification
Watch Features
Operating Instructions
Crown Positions
Manual Winding
Changing the Time
Changing the Date
Adjusting Straps & Bracelets
Water Resistance
Care
2
4
6
7
8
10
12
14
16
22
24
CONTENTS

INTERNATIONAL WARRANTY
Automatic watches from Larsson & Jennings are
guaranteed for 5 years from date of purchase.
The watch movement, hands and dial are the only
components covered during this warranty period.
These covered components will be repaired or replaced
free of charge if proven to be defective in material
or workmanship under normal use.
Please retain your International Warranty card, which can
be found inside the box, to serve as proof of purchase.
02

The warranty does not cover the following:
∙ Damages, and/or malfunctioning of the watch after
the terms of warranty.
∙ Damages, and/or malfunctioning of the watch, caused by
unauthorised persons or its representatives.
∙ Water damage.
∙ The strap, crystal sapphire glass, crown or buckle
∙ Postage, insurance and other non-repair expenses are
excluded from warranty and are the customer’s liability.
INTERNATIONAL WARRANTY
03

WATCH SPECIFICATION
04
S
W
I
S
S
M
A
D
E
STHLM / LDN
39mm
20mm
9.85mm
35mm

Watch
Movement
Case Back
Display Glass
Water Resistant
Case Diameter
Case Thickness
Dial Diameter
Lug Width
- Saxon Automatic
- ETA 2892.A2 / 21 Jewels
4Hz / 28’800 vph
42 hour static power reserve
- Exhibition / Mineral Glass
- Sapphire Crystal
anti-reflective / anti-fingerprint
- 10ATM
- 39mm
- 9.85mm
- 35mm
- 20mm
WATCH SPECIFICATION
05

1. Hours
2. Minutes
3. Sweeping Seconds
4. Date
5. Crown
KEY
WATCH FEATURES
06
S
W
I
S
S
M
A
D
E

OPERATING INSTRUCTIONS
07
Automatic watch movements generate their own power
from the activity of the wrist while wearing the watch.
The watch holds a power reserve of 42 hours when fully
wound - this power reserve will gradually diminish when
the watch is not being worn. When the power reserve is
depleted, the watch can be wound be hand.
Please refer to ‘MANUAL WINDING’ on page 10.

CROWN POSITIONS
08
S
W
I
S
S
M
A
D
E

Position 1 - Closed
Position 2 - Open, for manual winding
Position 3 - Date Change
Position 4 - Time Change
CROWN POSITIONS
09

10
MANUAL WINDING
S
W
I
S
S
M
A
D
E
Clockwise

11
MANUAL WINDING
Unscrew crown to Position 2.
When Power Reserve is depleted or the watch has
stopped, wind the crown clockwise 5-10 times maximum.
Stop winding when you feel some resistance, as
over-winding may cause tension damage inside the
movement. If the watch is running, manual winding is
not necessary.
Once you have wound your watch, return the crown
to Position 1 by pushing and screwing the crown back
against the case.
Please ensure the crown is set back to the watch’s operating position
for full water resistance.

12
CHANGING THE TIME
S
W
I
S
S
M
A
D
E

13
CHANGING THE TIME
Unscrew crown and pull the crown out to Position 4.
Adjust the time by turning in either direction.
Once you have changed the time, return the crown to
Position 1 by pushing and screwing the crown back
against the case.
Please ensure the crown is set back to the watch’s operating position
for full water resistance.

14
CHANGING THE DATE
S
W
I
S
S
M
A
D
E
Clockwise

15
CHANGING THE DATE
Unscrew the crown and pull the crown out to Position
3. Turn the crown clockwise, going through the date
numbers to reach the correct date. Resetting the date
will be required at the end of months that are shorter
than 31 days, due to the 31 date wheel. Once you have
changed the date, return the crown to Position 1 by
pushing and screwing the crown back against the case.
N.B The date should not be set when the hour hand is
between the hour markers of 10 o’clock (pm) and 1 o’clock
(am)
Please ensure the crown is set back to the watch’s operating position
for full water resistance.

ADJUSTING THE CLASP (Milanese clasp)
Insert the strap tool into the clasp gap.
16
Gently pull down until flat to release the full clasp
movement. Adjust to suit the size of the wrist, and replace
the clasp once comfortable.
Please ensure the clasp is securely fastened to its original position
before wearing.