Laser Optronix LD200 Mounting instructions

LD200/400 Laser Globe Camera
User Operation Manual
Thank you for using our company’s products. Please read this operation
manual carefully before using it, as it can provide you with correct technical
indicators and the things that you should pay attention to!
Please contact us if you come across problems that are not mentioned in
this instruction. We will supply you with satisfying technical support.

2
Active Laser Dome Camera
integrate laser illumination, color block camera into a whole dome
camera；
synchronous zoom + super wide angle：2°〜45°；
23X visible CCD camera；
Independent developed laser diode; long lifetime up to 20000 hours；
0.05°~360°/s high speed；
Laser Dome Camera LD200/400 PTZ www.laseroptronix.se

3
Intelligence function：auto reversal、presetting、cruise、self-
checking、record pattern etc；
Technical Indicators
Power supply
AC24V±10%
Interface
RS485、compound video output、AC24V
Technical
Indicators
Performance
Night vision distance＞200m（to people）；
day vision distance＞400m
Technical
Indicators
MTBF
≥10000 hours
Technical
Indicators
Fatigue Test
Continuously 10000 times test
Safety
Indicators
Laser spot
When power on, laser spot is biggest (default)
Safety
Indicators
Thunder proof
Consistent with GB / T 17626.5-1998 AC
power cord less than Grade Three; DC, signal,
control and other input line can afford surge
(impact) interference of Grade Two
Environmental
Indicators
Working
temperature
-25℃〜+55℃
Environmental
Indicators
Storage
temperature
-40℃〜+80℃
Environmental
Indicators
Protection
Grade
IP65
Environmental
Indicators
Vibration
Indicators
Comply with GB/T 1857.10
Color CCD
Camera
Model
23X，1/4’’ infrared sensitive CCD
Pantilt
Function
Pan Speed
0.05°~360°/s
Pantilt
Function
Pan Range
360°
Pantilt
Function
Tilt Speed
0.05°~180°/s
Pantilt
Function
Tilt Range
0°~180°，auto reversal
Pantilt
Function
Presets
At most 256
Pantilt
Function
Scan speed
0.5°〜30 °/s
Pantilt
Function
Cruise function
6 tracking paths
Pantilt
Function
Self-checking
40s
Pantilt
Function
Wiper
Has wiper
Illuminating
function
Laser power
4W
Illuminating
function
Lighting Angle
2°~45°，big angle synchronous zoom
Illuminating
function
Illuminating
Zoom Speed
3S quick zoom
By Laseroptronix www.laseroptronix.se
Laser Dome Camera LD200/400 PTZ www.laseroptronix.se

4
Warning：Remind user of potential danger!
1. Please read this instruction carefully before installing this device.
2. Please obey the warnings on the device and the instruction.
3. During the process of transporting and using, please avoid strong vibration and
compress in order to protect the optic and electronic components.
4. Please use the power supply equipped by us and obeys the methods of instruction
to connect the wire.
5. Don’t open the device by yourself, or else it may cause electric shock or machine
damage. If there are problems, please contact us and remember that never try to
mend it by yourself.
6. In order to protect the machine and people, this device need to be settled on firm
pan-tilt.
7. Please install appropriate lightning proof equipment to avoid thunder.
8. Use this device within the limitation of humidity and temperature.
9. To protect the imaging components from damaging, please don’t let the camera aim
at sun and other objectives of high light or aim at static bright objectives for a long
time.
10. Don’t look the laser window in close distance, or else it may hurt your eyes.
11. This is a class 3B laser unit so it is dangerous for the eyes at short ranges. Do
never stare into the laser aperture at front.
Attention
1. Don’t hide the sensitive components in front of the machine in order to make sure
the device would work normally.
2. If the night vision device is out of power supply, please restart it after 30 seconds.
Laser Dome Camera LD200/400 PTZ www.laseroptronix.se

5
Safety Warning:
Non insulation voltage to people
Please don’t stare at Laser Window when
power on. Class 3B laser unit
Avoid eyes staring straight
Laser Dome Camera LD200/400 PTZ www.laseroptronix.se

6
The First Part Introduction
Part Ⅰ---Features
Adopt laser illuminating system, long lighting distance and wide lighting field
low light color to black camera, can realize continuous monitoring day and night
shifting pan-tilt, realize omnidirectional no blind spot monitoring and high accurate
orientation
high intelligence, easy to operate and maintain
uneasy to be discovered
smart shell with professional design, light, firm, thermostabilization, anti-corrosion,
waterproof and acid rain proof
low power consumption, little heat, stable performance
Part Ⅱ---Technical Indicators
Item
Item
LD200/400 PTZ
Configuration
camera
Integrated camera
Configuration
illuminator
Infrared laser illuminator
Configuration
Power supply
AC24V±15% Iin≥2.5A
Configuration
interface
RS485、video output、AC 24V power supply
Technical
indicators
capability
Night vision distance＞200m;
Daytime vision distance＞400m
Technical
indicators
Power
consumption
≤50W
Technical
indicators
weight
7.5Kg
Technical
indicators
dimension
404*280*280
Environment
indicators
Working
temperature
-25℃〜+ 55℃
Environment
indicators
Storage
tempeature
-40℃〜+ 80 ℃
Environment
indicators
Anti-impact
≥4G
Environment
indicators
Salt-fog proof
Continuously spray fog for 48 hours under PH6.5-7.2
Environment
indicators
Protection Grade
IP65
Environment
indicators
Relative Humidity
90%
Video camera
indicators
Valid pixel
752（H）X582（V）
Video camera
indicators
Focal length
f＝4.1~73.8mm
Video camera
indicators
FOV
2.8°〜48°
Video camera
indicators
Signal-to-noise
≥50db
Video camera
indicators
Video output
VBS：1.0Vp-p
Video camera
indicators
Electronic Shutter
Quick 1/50,1/75,1/100,1/120,1/150,1/215,1/300,1/425,
1/600,1/1000,1/1250,1/1750,1/2500,1/3500,1/6000,1/10000
Video camera
indicators
Electronic Shutter
Slow 1x,2x,3x,6x,12x,25x
Illuminator
Illuminating
elements
Infrared laser illuminator
Illuminator
Wave length
808nm
Illuminator
Lighting angle
2°~45° Field of view
Laser Dome Camera LD200/400 PTZ www.laseroptronix.se

7
Illuminator
Power
consumption
10w
Illuminator
Illuminator control
automatic/ menu manual control
Basic function
of pan-tilt
Pan speed
0.05°~360°/s
Basic function
of pan-tilt
Tilt speed
0.05°~180°/s
Basic function
of pan-tilt
Presets
256
Basic function
of pan-tilt
Scanning speed
0.5°〜30 °/s
Basic function
of pan-tilt
Cruising function
6
Basic function
of pan-tilt
Self-check
40s
Note: The AC24V power supply’s input voltage should be
AC187V~AC253V. The voltage cannot be higher than AC253V, or else it
will cause product damage.
Part III---Function Introduction
1. infrared laser illuminating system
a. Realize electronic varifocus adjust of lighting source, laser beam angle
continuously adjustable
b. Laser beam expanding and shaping, light
intensity homogenization, light spot uniformity,
good lighting effect
c. Using the technology of laser power soft starting
and illuminator automatically control the
temperature, the lifetime of the laser illuminator
is prolonged.
d. High laser output efficiency, low power
consumption, stable performance
e. Using sensitive components to realize the
automatic “ON” or “OFF” of the laser. At daytime,
the laser illuminator will not start; when the illumination is lower than set , the
illuminator will automatically start.
Laser Dome Camera LD200/400 PTZ www.laseroptronix.se
MAIN MENU
= = = = = = = = = = = = = =
1 DISPLAY SETUP
2 CAMERA SETUP
3 CONTROL SETUP
4 PROGRAM
5 CAM DEFAULT SET
6 COMMUNICATION SETUP
7 SYSTEM RESET
8 EXIT
DISPLAY SETUP
= = = = = = = = = = = = = = = =
1 ID DISPLAY ON
2 ID POS TOP-L
3 TITLE DIS OFF
4 PRESET POS 0 1
5 CAM DISPLAY OFF
6 RETURN

8
f. Menu control of illuminator: the system normally in a state of “AUTO”, using the
sensitive components to inspect the outside light, automatically open or close the
illuminator; if you need to open the illuminator in special conditions, you can use
the menu to change the state into “ON”, at this time the laser illuminator will start
(not affected by outside); similarly, if you need to close laser illuminator, you can
use the menu to change the state into “OFF”, at this time the laser illuminator will
close (not affected by outside).
2.low light level color to black integrated camera
a. Use menu to set the function of camera.
b. Automatic switch between color and black/
white: when the light intensity is higher than
set, the camera is in a state of “color”; when
the light intensity is lower than set, the camera
is will automatically change into a state of
“black/white”, combining with laser illuminator
to realize night monitoring.
c. Zoom adjust: you can adjust “WIDE” or
“TELE” according to your needs to realize the
adjust of image.
d. Auto focusing: the camera uses the image
identity technology to realize automatic focus;
the image is clear and steady.
e. Back light compensation: when the background is too dark, you can open the back
light compensation according to your need.
f. White balance: when confronted with the situation of image color distortion , you
can choose the best imaging mode according to your practical situation (there are
six modes to choose, ①indoor mode ②outdoor mode ③one push mode
④automatic following mode ATW ⑤automatic mode
g. Low light level set: normally the camera is in a state of automatic working; when
the environment brightness is lower than 1Lux, the camera will automatically
change into zero level state. You can also use manual method to make the
camera in a state of zero level.
3. Integrated full range shift pan-tilt
a. Pan rotate 360º, tilt rotate 0º〜95º with
180°auto moving function.
b. Pan rotate can realize 0.05~360°/s continuous
shift adjust, tilt rotate can realize 0.05~180°/s
continuous shift adjust.
c. Low speed steady rotate, little noise, clear and
steady image.
d. Realize full range no spot monitoring,
exact orientation could reach ±0. 1°.
Laser Dome Camera LD200/400 PTZ www.laseroptronix.se
CAMERA SETUP
= = = = = = = = = = = = = = = = = = =
1 SHUTTER +2
2 BACK LIGHT OFF
3 ICR SHOT AUTO
4 D-ZOOM OFF
5 WB SET AUTO
6 SSNR MIDDLE
7 APERTURE 5
8 AGC AUTO
9 RETURN
CONTROL SETUP
= = = = = = = = = = = = = = = =
1 HOME OPTION
2 LASER LIGHT AUTO
3 WIPER OFF
4 WIPER MODE SERIES
5 DEFOGGER OFF
6 ZOOM RATIO 0 1
7 RETURN

9
4．High intelligence level
a. Can save at most 256 pre-setting points.
b. Pan scanning between two points. You can
choose the scanning speed and direction.
Thermal camera could scan about
180°between two points via menu.
c. Six tracking paths can be programmed: Each
path has 20 pre-setting points. You can
separately set the speed and staying time between two points.
d. Self-inspection function: The system can remember the PTZ paths in 40 seconds
and imitate; it can finish the action according to your operation; and data saves
when power off.
e. Character adding function: Screen can show camera’s address and number of pre-
setting.
f. Short/long focal length automatic shift function: according to camera’s focal length,
system could automatically adjust its pan and tilt rotating speed. Higher
magnification camera, its slower rotation speed to ensure an accurate search and
lock control objectives; smaller magnification camera, the faster rotation, to ensure
the movement speed of the night vision, in order to monitor targets quickly .
Part Ⅳ---Menu Set Instruction
1.Menu basic operation
a) Use keyboard or matrix to call No. 64 pre-setting
position to open the main menu.
b) When the menu is on the screen, with the
keyboard, you can control rocker to move; turn
up or down to move cursor to the item that need
set, turn left or right to amend the contents or
enter this item to set;
When using matrix, operate “TILT UP”、“TILT
DOWN” to move cursor to the item that
need set, operate “PAN LEFT”、“PAN RIGHT” to
amend the contents or enter the item to set.
Laser Dome Camera LD200/400 PTZ www.laseroptronix.se
HOME OPTION
= = = = = = = = = = = = = = = = =
1 AUTO HOME ON
2 HOME POS 0 1
3 DWELL TIME 0 5 MIN
4 RETURN
PROGRAM
= = = = = = = = = = = = = = = = = =
1 AUTO PAN START POS
2 AUTO PAN END POS
3 RUN AUTO PAN
4 SET TITLE 0 1
5 SET PATROL 0 1
6 RUN PATROL 0 1
7 RECORD PATTERN
8 RUN PATTERN
9 RETURN

10
c) Night vision camera has the function of memory when power off, with which the
data can’t be lost
d) Main set of the menu, please refer to the “Menu Setup”
2.Menu Setup
a. MAIN MENU
DISPLAY SETUP：Enter the submenu of screen display set. You can set ID
display、pre-setting position title display and camera display mode。
CAMERA SETUP: Enter the submenu of camera parameter set.
CONTROL SETUP：Enter the submenu of night vision control parameter set.
PROGRAM: enter the submenu of night-vision enhancements.
CAM DEFAULT SET: restore default settings.
COMMUNICATION SET: enter sub-menu of communication parameter.
SYSTEM RESET: achieve System reset function.
EXIT：exit the main menu.
b. DISPLAY SETUP
ID DISPLAY: When this item is ON, the screen
will show the address of the night vision
camera, for example, “CAM 006”. Default set is
ON.
ID POS：Set the address display position. The
address can be displayed at the three corners
of the screen: TOP-L( top left), BOTT-R (bottom right), BOTT-L (bottom left).
TITLE DIS：If this item is set ON, the left of the screen
will show the title of pre-setting position when you call the
pre-setting position. For example, “NO.001 ABCDEFGH”.
If there is no title of this position, it will only display
“PRESET NO.001 NO TITLE”. The set of amendment of
pre-setting position’s title is under the menu of
PROGRAM. When the title of show off, the screen only shows preset number.
PRESET POS：Set the display position of pre-setting position’s title. It could be
the first line to the tenth line. The first line is on the top of the screen.
CAM DISPLAY: If this item is set “ON”, the camera’s screen display will be open.
the camera function parameters is on the screen.
RETURN: return to the main menu.
2.3 CAMERA PARAMETER SETTINGS
Frame accumulation: there are three options: automatic, shutter and slow gate. The door
series of slow gate and shutter are 16 and 6 separately. If a slow shutter and door state,
when the camera screen display is open, the monitor will display the frame rate of
Laser Dome Camera LD200/400 PTZ www.laseroptronix.se
PRESET POINT: NO. 001
TILT ：NO TITLE
CLOSE：EXIT
COMMUNICATION SETUP
= = = = = = = = = = = = = = = =
1 CAM ID 001
2 PROTOCOL PELCO-D
3 BAUD 2400bps
4 RETURN

11
accumulation. (If the night is slow to focus, check the settings for the automatic.)
.1 SLOW SHUTTER: three options: automatic, shutter and slow gate. Slow shutter and
door series were 12 and 12. when under shutter and slow gate situation. once the
camera screen display is open, the monitor will display the frame rate of accumulation.
(If slow to focus in night, please check whether the settings is automatic.
.2BACK LIGHT: there are two operation options: open /
closed.
.3ICR SHOT:turn on manually, or automatically control.
.4D-ZOOM: set to turn on / off two states
.5WB SET: ATW / INDOOR / OUTDOOR / ONEPUSH /
AUTO / MANU
.6SSNR：Noise reduction options, there are three
models: low, medium and high.
.7EXP COMP VALUE: SET the range 1~16.
.8AGC: there is a total of 14 options Automatic gain,
ranging from 2dB to 28dB. Frame accumulation and
gain only work in the laser opened.
.9 RETURN：return to the main menu.
.4 CONTROL SETUP
.4.1 HOME OPTION：Enter the submenu
of setting automatic return function.
.4.1.1AUTO HOME：When this item is “ON”
open the automatic return function.
It means that if the user has no action within
a period of time, the night vision will return to HOME.
When the night vision camera is in a state of patrol,
it will not return to HOME. When without the need to
return to HOME, please set this item in “OFF”.
.4.1.2HOME POS：HOME is the return position. For example, when you need to setup
a scene as HOME, you should first adjust to this scene, setup the pre-setting
position as No.3, then move to the menu and enter this submenu; change the
number behind HOME POS into 3. This is OK. If you want to make the
automatic function take effect, donot forget to setup the AUTO HOME in “ON”.
HOME POS can be pre-setting position 1-50.
.4.1.3DWELL TIME：Setup the automatic return time, which means how long it will
return to HOME without control. The time can be one minute to 99 minutes.
.4.1.4RETURN：return to the last menu.
.4.2 LASER LIGHT：Laser illuminator open item: normally, the system will
automatically inspect the outside lighting level, automatically open or close laser
illuminator; if the user changes this item into “ON”, this system’s laser control is
changed into manual. If you need to return to the automatic state, you must change
this laser menu into the state of “AUTO”.
Laser Dome Camera LD200/400 PTZ www.laseroptronix.se

12
.4.3 WIPER：Wiper control item, with wiper mode, controls the wiper to move once or
continuously.
.4.4 WIPER MODE：you can choose the ONCE mode or CONTINUOUS mode, the
default is CONTINUOUS mode.
.4.5 DEFOGGER：Defogger control item, if you open this function, the system will start
for 2 minutes and close after 2 minutes.
.4.6 ZOOM RATIO: Set the zoom minimum of lens, 8 classes.
.4.7 RETURN：Return to the main menu.
.5 PROGRAM
.5.1 AUTO PAN START POS：Setup Auto pan start position. After you enter, use the
rocker to adjust the night vision monitoring position. Push CLOSE key-press to
save the current position and return.
.5.2 AUTO PAN END POS：Setup Auto pan end position. After you enter, use the
rocker to adjust the night vision monitoring position. Push CLOSE key-press to
save the current position and return.
.5.3 RUN AUTO PAN：pan function run line between two points, run and press OPEN key
to exit the menu. Please set a good run before the start and end line scan, line scan
from the beginning to the end with the menu item settings 1 and 2.
.5.4 SET TITLE：Set the title of pre-setting position. Only the former 63 pre-setting
positions can have title. Use PAN LEFT/PAN RIGHT to choose pre-setting position
number, push OPEN key-press to enter the edit state; push CLOSE key-press to
leave the edit state. The operation under the edit state please refers to the back.
.5.5 SET PATROL：Edit patrol parameter. Use PAN LEFT/PAN RIGHT to choose paths
number; use OPEN to enter the edit state, push CLOSE key-press to leave the edit
state. The operation under the edit state please refers to the back.
.5.6 RUN PATROL：Run patrol function. Use PAN LEFT/PAN RIGHT to choose paths
number, push OPEN key-press to run and leave.
.5.7 RECORD PATTERN：Edit tracking self-inspection, can record PTZ operation
within 40 seconds at most. The 40 seconds is up or push CLOSE key-press to
finish edit.
.5.8 RUN PATTERN：Run tracking self-inspection. After it is run, you will leave the
menu. The control of the rocker can stop its run.
.5.9 RETURN：Return to the main menu.
.6 COMMUNICATION SETUP
.6.1 ADDRESS: set address range is 1-255.
.6.2 PROTOCOL: PELCO-D option or PELCO-P.
.6.3 BAUD: Baud rate from 2400bps to 19200bps optional.
.6.4 RETURN: return to the main menu.
Note: The communication parameters need to reboot after saving changes.
Laser Dome Camera LD200/400 PTZ www.laseroptronix.se

13
3 Menu Appendix
.1 PRESET TITLE EDIT MODE OPERATION
Enter into edit mode, the screen shown in figure:
From the figure we can see that the current setting is No. 1 preset point, the title is "NO TITLE".
With PAN LEFT / RIGHT to move the cursor, TILT UP / DOWN can modify the value. CLOSE
exit edit mode press the button and save the changes. Preset title can contain up to 8
characters, these characters can be 0 ~ 9, A ~ Z, +, - and blank.
3.2 MULTI-POINTS INSPECCTION EDIT MODE OPERATION
Into edit mode, the screen displays as follow:
NOTE：
NO: tracking point number
POS: pre-setting positions number
TM: the staying time at this pre-setting position
SEQ: 01 displays the current setup is 1
CLOSE:EXIT push CLOSE to exit
The top line and bottom line show the indicating information, the middle shows every
tracking paths information. Every line shows 2 tracking points parameter. Use PAN LEFT/
RIGHT to move cursor, use TILT UP/DOWN can amend the number. Continuously push it
for one second will accelerate. Push CLOSE key-press to exit the edit state and save the
amendment. The program will search the first POS with the position of “000”, and will save
the former data and treat the latter data as invalid. As the picture above, the program
saves the four tracking points. The scope of POS is 1-128. When POS is “000”, it means
the end of the tracking scope. TM’s scope is from 0 to 99 seconds.
Part V---Night Vision camera’s Connection Instruction
The power supply input, control signal input and video signal output uses one group of
compound cable, which will be fetched out by the seven cores aviation outlet.
Part No
Definition
Remarks
1
AC24V: Red
AC24V Input
2
AC24V: Black
AC24V Input
3
RS485-: Yellow
485 Controls B
5
RS485+: orange
485 controls A
6
Video+
video output +
Laser Dome Camera LD200/400 PTZ www.laseroptronix.se

14
7
Video-
video output -
Laser Dome Camera LD200/400 PTZ www.laseroptronix.se

15
The Second Part Installation Instruction
1. Shape and dimension
Night vision camera’s shape and dimension (mm)
Installation reference diagram
Installation Graphics
a) Please go ahead with the M6X16 bolts factory offered in the box.
b) Avoid shaking and extrusion during fixing for protecting key components and optics
Laser Dome Camera LD200/400 PTZ www.laseroptronix.se

16
inside. Signal transmission line should be kept 50m away from high voltage devices
and cables.
c) Circuit thunder prevention and grounding design should be in accordance with
construction demand and standard of local regulations and industry. The ground
resistance is less than 4Ω,and the ground wire section should more than 25mm2
connected.
d) The out connecting cables should be fixing tightly to the outlet to keep form water.
2. System Connection Reference
Night Vision should be combined with other equipment into the system, using simple
system diagram below shows:
3. Common Failure Analysis
problem
possible reason
solving method
the night vision camera has
no action and no image in
the state of power-on
the power supply is
damaged or the power
is not sufficient
Change
the night vision camera has
no action and no image in
the state of power-on
wrong connection of
power supply line
correctly connect
the night vision camera has
no action and no image in
the state of power-on
line failure
Eliminate
Unusual self-inspect, has
image but also has motor
noise
Engine failure
Mend
Laser Dome Camera LD200/400 PTZ www.laseroptronix.se

17
Unusual self-inspect, has
image but also has motor
noise
Insufficient power
Use the right power
Good self-inspect, but has
no image
Wrong connection of
video cable
Change
Good self-inspect, but has
no image
Not good connection
of video cable
eliminate
Good self-inspect, but has
no image
V i d e o c a m e r a i s
damaged
change
Good self-inspect, but can
not control
Wrong connection of
control signal line
change
Good self-inspect, but can
not control
Wrong match of
address
Reset the controller’s address
Good self-inspect, but can
not control
Wrong match of
protocol
Adjust the controller’s protocols to
match the night vision camera
Not steady image
Not good connection
of video line
eliminate
Not steady image
Insufficient power
change
Night vision camera out of
control
Unusual self-inspect
Restart the electricity
Night vision camera out of
control
Not good connection
of control line
eliminate
Night vision camera out of
control
Problems with the
mainframe operation
Restart the electricity of the
mainframe
Night vision camera out of
control
Too much load or too
long distance of
communication
Connect the farthest 120 ohm
resistor, others are cut.
Add …..
Manual/ automatic lose
effect
Illuminator maybe
damaged
Return us to mend
Wiper not moving
Location biased
Check wipers whether in the correct
position
We have listed the reasons of the common problems and solvent to the problems,which is
just for reference. If you have come across some other new special problems, please
contact us directly. We will provide you with satisfactory technical support.
Laser Dome Camera LD200/400 PTZ www.laseroptronix.se

18
The Third Part
Instructions of quality guarantee and after-sales service
Quality guarantee and after-sales service by Laseroptronix
We do business based on customers’ satisfactions and quality is the most
important thing for us. Our company has many kinds of military industry technologies
and unique key technology. Our products have advanced properties and the quality is
reliable.
Because we have advanced technology, much experience and the customer-
centered service idea, we can manufacture products according to your needs and give
you a system that is practical and of good-quality.
All our products have the attachment of detailed installation and operation
instructions. Therefore, it is very convenient. And with the permission of the situation,
we can send technicians to install for you.
If you have any problem of the quality, technology and operation, welcome to
contact us. And we will give you the satisfactory reply within 2 hours after we received
your call. Then we will solve the problem for you as soon as possible.
Welcome all the customers to give us different kinds of suggestions. Your support
is the driving force for our development forever, thank you!
Laser Dome Camera LD200/400 PTZ www.laseroptronix.se

19
Appendix Ⅰ: RS 485 LINE
1. RS485 Features
RS485 Industry Line is communication line of speciality impedance 120Ω, and
support 32 node at most, including controlling and controlled equipments.
2. RS485 Transmission Distance
0.56mm(24AWG)twisted pair line as communication line
Baud Rate
Farthest Transmission
Distance
2400 Bps
1800m
4800 Bps
1200m
9600 Bps
800m
3. Connection and terminal resistance
RS485 industry line requires chain connection among all devices, and both ends
should be with 120Ωterminal resistance.
But” D” section should not exceed 7 m.
Connection of 120Ωresistance: this resistance has been ready on circuit board,
and default isthat it’s on 2~3, and 120Ωisn’t connected. When needs to connect to
120Ω, please replace it on 1~2 circuit.
Laser Dome Camera LD200/400 PTZ www.laseroptronix.se

20
4. Problems in cases
Customers often uses Star Chain in cases, and terminal resistance must connect
farthest two devices. As following sketch, 1 ＃and 15 ＃can’t accord with RS485,
it result to signal reflection and anti-jamming ability reduction. Regarding this
problem, we recommend to use RS485 Divider, which can change Star Chain to
suitable connection way, and avoid problems to promote communication.
Laser Dome Camera LD200/400 PTZ www.laseroptronix.se