Leader LD-CLD1.0 User manual

LD-CLD1.0
COLOR SMOKE APPLICATOR
User Manual V1.0
2023.03
Please read this book carefully and keep it properly before using this product
If you have any questions, please contact the sales personnel

1
Cautions
Precautions during operation
1. Check whether the power supply line is connected properly, and whether the
video signal line is connected to the designated interface and plugged in
properly.
2. Check if the connection between the mounting components and the drone is
securely installed.
3. Check the launch angle of the cigarette dispenser, as improper angle may
cause damage to the drone or cigarette dispenser.
4. Is there a drone camera or other equipment in front of the launch port that
needs to be adjusted to avoid obstacles.
5. Check if there are any personnel or buildings in front of the launch port, and
pay attention to safety during operation.
6. This device is dedicated to 38MM electric shock primer ammunition. Please
select the electric shock primer type ammunition before use.
7. Is the power of the remote control sufficient to avoid power outage during use,
which may cause the cigarette dispenser to lose control.
8. Check the production date and shelf life of the ammunition, and check if the
firing electrode of the ammunition has poor oxidation and conductivity.
9. Check if the remote control transmission switch is in the off position.
10. Check whether the locking of the magazine and rear cover is secure and
whether there is any trauma to avoid damaging the cigarette dispenser during
launch.
This cigarette dispenser is customized for use by a special unit. Non professional
personnel are prohibited from using it without authorization. Due to its strong
destructive nature, it is important to use it safely. Before confirming the need for
firing, please do not load ammunition. Our company is not responsible for property
damage or personal injury caused by improper use or non professional personnel.

2
Catalogue
Cautions...............................................................................................................................................1
Precautions during operation ................................................................................................1
Introduction...................................................................................................................................... 3
LD-CLD1.0 .....................................................................................................................................3
Part Name .....................................................................................................................................3
Installation......................................................................................................................................... 4
Mount installation ..................................................................................................................... 4
Connection between power cable and video signal cable .........................................5
Control and Operation...............................................................................................................6
Remote control operation...................................................................................................... 6
Ammunition loading operation ............................................................................................7
Introduction of applicable ammunition..........................................................................7
Types of Electric Shock Ammunition .................................................................................. 7
SPEC..................................................................................................................................................9

3
Introduction
LD-CLD1.0
This product is a 38mm caliber cigarette dispenser for unmanned aerial vehicles,
which can be adapted to the DJI M600 PRO and various other unmanned aerial
vehicle flight platforms, and is compatible with a variety of ammunition types.
Support independent remote control and M600 expansion channel function,
modular quick disassembly design, convenient and fast disassembly. The 38 mm
caliber 8 power generation percussion bomb has the capacity to load smoke
grenade, tear gas, shock detonation bomb and other kinds of ammunition, and is
suitable for military, anti-terrorism, fire fighting, rescue, drill and emergencies.
Part Name
1. Mount mounting parts
2. Firing port
3. FPV camera
4. Ignition indicator light
5. Signal line socket
6. Power socket
7. Magazine cover
8. Ignition contact
9. Ammunition loading port
10. Magazine lock

4
Installation
Mount installation
Pick up the mounting plate, unscrew the hand screw on the mounting parts to open
the upper cover of the mounting parts of the mounting parts of the mounting parts,
open all the upper covers of the four mounting parts, take them to the lower part of
the UAV, align the gap of the mounting parts with the left and right mounting bars,
cover the upper cover of the four mounting parts, and adjust the position front and
back to ensure that the mounting is near the center of gravity of the UAV. Then
tighten the screws by hand. Complete the connection between the mount board
and the drone.

5
Connection between power cable and video signal cable
Firstly, plug one end of the power cord into the power socket of the cigarette
dispenser, and connect the XT30 power plug on the other end to the positive and
negative poles of the power plug under the body (24V interface).
Insert the red plug of the video signal cable into the AV signal plug, and the white
plug is the connector for connecting to the LB2 high-definition image transmission
AV video input port. When connecting to the M600, remove the plastic protective
shell below the body, pass through the wire hole on the body, and plug it into the
LB2 high-definition image transmission AV input port.

6
Control and Operation
Remote control operation
Pick up the remote control, open the battery cover behind the remote control, and
insert four No. 5 batteries into it. Be careful not to reverse the positive and negative
poles, and install the battery cover. On the front of the remote control, push all the
top switches forward to reset them. Hold down the power button with one finger in
each hand for 2 seconds, and the remote control screen will light up and a power
on prompt sound will sound. The remote control is turned on. When turning off the
computer, use one finger with each hand and press the power switch for about 3
seconds. The remote control will sound a beep, and then the screen will turn off.
After the drone reaches the launch airspace, the pitch angle of the cigarette
dispenser is controlled by pushing or pulling down the right joystick of the remote
control, observing the first perspective image returned by the camera, aiming at
the target, and the direction axis needs to be aligned. The drone pilot needs to
adjust the drone's heading.
After confirming the alignment with the target, pull down the launch switch, the
electronic igniter will work, ignite the ammunition in position 1, and then fire the
ammunition. Pull back the launch switch, pull down again, and fire the ammunition
in position 2, and so on, fire 8 ammunition.
When launching each round of ammunition, the recoil force will lead to the change
of the pitch angle of the cigarette dispenser. The operator needs to use the remote
control to control the compensation angle and aim at the target.
VIDEO INSTALLATION TUTORIAL

7
Ammunition loading operation
Pick up the cigarette dispenser and press the unlocking wrench at the magazine
lock position inward. Be sure to press both the left and right magazine locks
simultaneously, and then the back cover will pop up a gap. Open the back cover
and load the ammunition. Please refer to the numerical number below the red
indicator light on the back cover for the order of loading ammunition,
corresponding to the order of firing. After loading ammunition, press the unlocking
wrench in the magazine lock position again, close the back cover, and then press
the back cover to observe the automatic insertion of the unlocking wrench,
completing the loading and closing of ammunition.
Introduction of applicable ammunition
Types of Electric Shock Ammunition
The first：
There is no silver anodization on the surface of the shell, and the shell conducts
electricity with the outer ring of the primer, so this ammunition can be used directly.

8
The second：
The surface of the shell has silver anodization, the shell and the outer ring of the
primer are not conductive, this ammunition must polish the surface of the shell
outside the outer ring of the primer to the metal primary color, in order to
successfully make the shell and the primer completely conductive, in order to
meet the requirements of use.
The third：
The shell is made of plastic, but there is an anodized metal part in the outer ring
of the base fire position, and the anodized surface also needs to be polished off
to meet the requirements of use.
Note: Some ammunition is not an electric shock type, or is not suitable for this
color smoke dropper, please do not force it into the color smoke dispenser.

9
SPEC
Specifications
Color smoke applicator
Product size
220mm*135mm*260mm
Outer packing box
473mm*348mm*185mm
Net weight
3.85 KG
Material quality
POM Saigang, aviation aluminum, carbon fiber,
stainless steel materials
Installation method
Quick release type
Launch method
Electric shock
Caliber size
38 mm (adaptation: 1~2kg recoil, 80m range,
electric shock)
Loading capacity
8
Power supply mode
Airborne power supply
Working voltage
DC 12-28V
Control mode
Independent remote control PWM signal
Controlling Distance
800M
Control angle
Pitch axis 360 degrees
Expand channels
Can support M600 expansion channel function
(If you need this feature, please contact sales first)
Application
M600 Pro and Rufeng series (other independent
models, please contact sales first)
Camera
Effective pixels: PAL: 976 (H) * 494 (V);
NTSC:768（H）*494（V）

10
Remote control
Overall dimensions
180*82*161mm
Weight
392g
Input power supply
6V 1.5AA*4
Data output
PS2 interface PPM
Frequency range
2.4055 - 2.475GHZ
Band width
500KHZ
Transmitter power
Not higher than 20dBm
Low voltage alarm
Below 4.2V
Charging interface
Not have
Length of antenna
26 mm*2(dual antenna)
Display method
STN semi transparent forward display,
128x64 dot matrix VA73*39mm LED white backlight