LEADER AER AL LD-TFX 1.0 User manual

LD-TFX 1.0
DRONE DROP BOX
User Manual V1.0
2023.03
Please read this book carefully and keep it properly before using this product
If you have any questions, please contact the sales personnel

1
Cautions
1. This device is equipped with a power interface and a signal interface
on the side, which must be suitable for the power supply line
provided by the original factory.
2. The applicable power supply for this device is DC12-26V. A voltage
below this range may cause it to malfunction, while a voltage above
this range may cause the device to burn out.
3. According to the different control methods, the receiver control
method and flight control method can be divided (if this function is
needed, please contact sales and technical support in advance)
4. The receiver mode is factory default preset and does not require user
adjustment.
5. The remote control requires 4 No. 5 batteries. Please pay attention to
the direction of the positive and negative poles when installing, and
follow the instructions icon to install it. Otherwise, it cannot be
turned on.
6. Please fully tighten the connectors during use to avoid loosening and
falling, which may cause flight accidents.
7. Please do not collide during transportation or handling to avoid
structural deformation that may affect normal operation.
8. The intention of using drone flight safety as the main focus and
placing items as a supplement should be emphasized.

2
Catalogue
Cautions ............................................................................................................................................1
Introduction.....................................................................................................................................3
LD-TFX 1.0 ................................................................................................................................3
Part Name ................................................................................................................................ 3
Installation ....................................................................................................................................... 4
Preparations............................................................................................................................ 4
Mount installation ................................................................................................................. 4
Control and operation ..................................................................................................................8
Remote control operation ...................................................................................................8
Material loading operation ................................................................................................. 9
SPEC................................................................................................................................................. 10

3
Introduction
LD-TFX 1.0
A drone airborne drop box suitable for logistics transportation and material airdrop.
The drop position is observed through the drone camera, and the drop box is
controlled by a remote control to open the cabin door and drop mission items. This
product is waterproof and dustproof, and is less affected by environmental factors.
It can effectively protect the safety of transported or dropped items and deliver
them to their destination. This product can be applied in multiple fields such as
public security, firefighting, electricity, material delivery, logistics transportation,
disaster relief, and isolated area rescue.
Part Name
1. Quick dismantling rack
2. Side door switch
3. side door
4. POWER PORT
5. signal port
6. Drop hatch

4
Installation
Preparations
Before installation and use, the following items need to be prepared:
M600 unmanned aerial vehicle, drop box, power supply line, quick disassembly
mounting rack, six channel remote control, and a set of signal receiver.
Mount installation
Firstly, install the quick release mounting bracket on the mounting bracket below
the drone body (note that the quick release mounting bracket with an infinite
position lock is installed in the direction of the aircraft nose, while the quick release
mounting bracket with a limit lock is installed in the direction of the tail, ensuring
that all the installation module push ports are facing the tail), determine the
distance between the two quick release mounting components, and tighten the
screws by hand.

5
Installation diagram of mounting bracket
Align the device quick disconnect bracket with the mounting bracket, push in the
quick disconnect bracket, and when you hear a "click" sound, check if it is securely
installed.
Drop box mounting

6
Align the mounting bracket buckle and push it in
After the loading of the drop box is completed

7
Insert the XT30 end of the power cord into the 24V voltage plug of the drone, and
the type-c end of the power cord into the power port of the drop box, regardless of
the front and back sides.
The yellow color of the receiver's wiring corresponds to the signal line, with the
direction of the yellow line corresponding to the S marked on the carbon board of
the drop box. The yellow color of the wiring faces the direction of the notch in the
receiver's No. 5 socket.
Note: The factory has been debugged and assembled, and do not make
unauthorized modifications.
Open the battery cover on the back of the remote control, follow the instructions to
install the battery, cover the battery cover, and complete the installation.

8
Control and operation
Remote control operation
Pick up the remote control of the drop box module, do not touch the joystick, reset
all the toggle switches above, press and hold the power icon button with both
hands and thumbs for about 3 seconds, and the remote control will turn on. The
shutdown method is consistent with the startup method.
After the screen displays a normal screen with no error prompt, turn on the
installed drone and power it on. At this time, there should be a sky voltage display
in the upper right corner of the remote control screen, indicating that the
connection has been successful. Otherwise, please contact technical support.
The "SWA" switch in the upper left fluctuates downwards, and the controller drives
the motor to open the cabin door lock.
After returning with the aircraft or before takeoff, it is necessary to manually lift the
cabin door to the closed state, then wave the "SWA" switch to the upper position,
and the controller drives the motor to close the cabin door lock.

9
Material loading operation
First, press and hold the button above to open the side door, place the items that
need to be placed, and close the side door to complete loading.
Side door item loading

10
SPEC
Specifications
Drop box
Product size
378*230*274mm（M600 Pro 款）
Outer packaging size
466*390*351mm
Inner cavity size
218*215*366mm
Side door size
207*190mm
Installation method
Quick release type
Dead-weight
1.70KG
Volume
≈17L
Max load
5KG
Supported platforms
Rufeng 4, Rufeng 8, M600 Pro, and aircraft with a
load capacity of over 5KG
Control model
Independent remote control
Controlling Distance
800M (without obstruction)
Expand channels
Can support M600 expansion channel function
(if you need this function, please contact sales first)
notes
Support customized onboard power supply or
independent power supply
Remote control
Overall dimensions
180*82*161mm
Weight
392g
Input power supply
1.5AA*4
Data output
PS2 interface PPM
Frequency range
2.4055 - 2.475GHZ
Band width
500KHZ
Transmitter power
Not higher than 20dBm
Low voltage alarm
Below 4.2V
Charging interface
not have
Length of antenna
26 mm * 2 (built-in dual antenna)
Display method
STN semi transparent forward display,
128x64 dot matrixVA73 * 39mm
LED white backlight