Leisure Time Products LTP PRO Series User manual

Table of Contents
LTP PRO Series
Adjustable Height
Goal System
• LTP672
Tab
le
of
C
TABLE OF CONTENTS
Safety Instructions ...................................................................... 2
Goal Specications...................................................................... 3
Determine Installation Specications.......................................... 3
Ground Anchor Installation ......................................................... 4
Pole Assembly............................................................................. 5
Extension Arm Attachments........................................................ 6
Jack Attachment ......................................................................... 7
Backboard Attachment ............................................................... 8
Goal Alignment........................................................................... 9
Rim Attachment........................................................................ 10
Height Indicator Adjustment..................................................... 11
Ready to Play ............................................................................ 12
Warranties ................................................................................ 13
INSTALLATION AND
INSTALLATION AND
OWNER’S INSTRUCTIONS
OWNER’S INSTRUCTIONS
[phone]

Safety Instructions
Owner must ensure that all installers and players know and comply with these
rules for safe assembly, installation, operation and use of the system. Proper
and complete assembly, use and supervision is essential for proper operation
of the product and to reduce the risk of accident or injury. DO NOT ATTEMPT
TO ASSEMBLE AND INSTALL THIS PRODUCT WITHOUT FOLLOWING THE
INSTRUCTIONS CAREFULLY.
WARNING
1. Failure to follow these instructions may result in death, serious injury
and/or property damage and will void the warranty. Do not install or use
this product unless the instructions within this manual have been care-
fully read and understood.
2. Locate your goal away from potential dangers, including walls, trip haz-
ards, high-trac areas or where a vehicle might come into contact with
goal post, backboard or rim.
To avoid severe injury or death, do not locate goal under power lines that
may come into contact with the goal as it
is raised.
3. Two or three people in good physical condition and capable of lifting at
least 90-100 lbs. (40-45 kg) each are recommended for safe installation
and assembly.
• If using a ladder during assembly, use extreme caution. Follow all warnings and
cautions on the ladder carefully.
• Installation and assembly of this product will require lifting and bending
that may result in injury to anyone not accustomed to this type of activity.
•
Before digging for the ground anchor, check for underground power, gas,
telephone, water and other utility lines. Failure to do so could result in serious
injury. See 811 One CallWarning box on this page for more information or call
your local utility company.
• If an auger or post hole digger is used, be sure you read and follow all
instructions, warnings and cautions for such equipment.
• Ensure there are no overhead power lines within a 20 ft. (7 m) radius of the
goal location.
• Climate, corrosion or misuse could result in system failure.
• Keep organic material away from the pole base. Dirt, grass, litter etc. could
cause corrosion or deterioration.
• Only use parts provided with your Leisure Time Productsbasketball goal
system or replacement parts provided by LeisureTime Products Use of other
parts (a) may cause the goal system to fail,
(b) could result in death, serious injury or property damage,
and (c) will void the warranty.
• With rim set at 7’-0”playing height, the minimum operational height is 6’-4”
(1.93 m) to the bottom of the backboard.
•DO NOT CLIMB THE POLE OR HANG on the rim or any part of the goal
system. This includes the backboard, support braces and net.The product is
not designed for such use and property damage or personal injuries such as
cuts, broken bones, nerve, spinal cord or brain injury or death could occur.
• Use caution when performing dunking activities with this product.
• During play keep players’faces away from the backboard, rim and net or
serious injury could result.
• Players must wear a mouth guard to avoid dental injuries.
2
• Do not wear jewelry (rings, watches, necklaces, etc.) or other loose objects
that could become tangled in the net or injure
another player.
•
Before each use, check the goal system for loose hardware, excessive wear and
signs of corrosion. Repair the system before use.
•NEVER play on damaged equipment.
•
When adjusting the system height, keep hands and ngers away from moving
parts. DO NOT allow children to adjust the system height.
• Check the goal system frequently for signs of corrosion. Remove surface rust
and loose paint completely, and repaint with exterior enamel paint. If rust or
corrosion has penetrated or pitted any components of the goal, DO NOT allow
play and repair or replace parts immediately.
• DO NOT use the goal system to lift or hoist anything.
• Use caution when using this goal system. Most injuries are caused by misuse
and/or not following these instructions.
IMPORTANT
Enclosed underneath the protective sheeting on your backboard is a
warranty registration card. YOU MUST FILL OUT AND
MAIL IN THIS CARD IN ORDER TO HAVE AVALID WARRANTY.
Retain this manual for future reference of operation, maintenance and parts
information.
The information in this manual is based on the latest information available at
the time of publication. Your goal may have product improvements and options
not yet contained in this manual. Leisure Time Products reserves the right to
make changes at any time without notice or obligation.
Contact the manufacturer if technical assistance is required.
Additional copies of these instructions are available from:
Leisure Time Products
1-800-856-4445
WARNING
Before digging for the ground anchor,
contact your local One-Call system
(dial 811) in your area.
Utility Markings
Color Denition
Red Electric
Yellow Gas, Oil, Petroleum
Orange Communication, Phone, TV
Blue Potable Water, Irrigation
Green/Brown Sewer
White Proposed Dig
1-888-258-0808

3
Goal Specications
Determine Installation Location
Consider the following to determine where to install your Leisure Time
ProductsBasketball Goal:
• When extended, will backboard overhang obstruct driveway or other
important space? Maximum overhang: 73”(1.85 m) from the front of the
pole to the front of the rim.
• Is there room so vehicles backing out of driveway do not strike backboard
or rim?
• Will court markings be used?
• How much playing surface is needed?
• How much playing surface will be under the backboard? (Having the edge
of the playing surface directly underneath the backboard can result in
trip hazards and unpredictable ball action following a shot.Try to have as
much playing surface as possible behind the backboard.)
• Other functions of playing surface (driveway, playground, etc.)
• Will the goal be at least 20 ft. (7 m) from any overhead power lines? (No
overhead power lines should be within a 20 ft.
(7 m) radius of the goal.)
• Will the ground anchor for the goal avoid underground power, gas,
telephone, water and other utility lines? (See 811 One Call Warning box on
page 2 for more information or call your local utility company.)
Required Tools and Materials:
• Spade • Wheelbarrow
• Shovel • Cement Trowel
• Tape Measure • Stir Rod
• Level • Auger/Post Hole Digger (optional)
• Hoe •
10-14, 60 lb Bags of Dry Concrete Mix
• Water (or
1/4-1/3yard of ready mix concrete)
• Rubber Mallet • 1/2”Drive Torque Wrench
• Steel Punch • Phillips Screwdriver
• Stepladder • 9/16” & 3/4”Wrenches and Sockets
LTP672
Pole Size: 6”x6”
Backboard Size: 42”x72”
Weight w/Acrylic: 475 lbs.
Weight w/Glass: 535 lbs.
(A) Height Range: 6’8”-10’
(B) Extension Distance:
at 10’ 42”
at 8’ 48”
at 7’ 46”
(C) Maximum Overhang: 73”
(D) Distance Rim to Backboard: 25”
(E) Distance Rim to Top of Goal: 33
3/4
”
(F) Crank Distance: 18”
(G) Crank Height: 42”
(H) Crank Turn Radius 10”
(I) Pole Height: 10’
A
B
DC
I
H
G
F
E
Playing Surface
6'-0"
19'-9"
50'-0" Optimum Inside Sidelines
15'-0"
19'-0"
25'-0"
63"
15"
12'-0"
4'-0"
Note:
Lines ar e 2" wide.
Court Markings
(Reference Only):
Regulation Court Lengths
High School: 84’
College & Professional: 94’
(Top of Plate)

4
TIME OUT TIP: The arrow on the decal
MUST be pointing toward the playing surface.
Step 6: Position 6” ground anchor (Item G2660) in
center of hole with hinge side toward and parallel with playing surface.
Using a level, ensure the anchor is level front-to-back and left-to-right. All
edges of the ground anchor must be 6”(15.2 cm) away from all sides of hole
and the top of the ground anchor within a range of 1”- 3”(25-75 mm) above
the level of the playing surface.
TIME OUT TIP: As you add concrete, occasionally
insert a stir rod (such as a broomstick) into three
or four places in the concrete and plunge up and
down to help eliminate air bubbles.
Step 7: Continue adding concrete until concrete is within
1”- 1.5”(25-38 mm) of anchor plate bottom, or level with the landscape –
whichever comes rst. Slope top of concrete away from pole with trowel to
create a smooth surface.
IMPORTANT
• Periodically re-check the level of the anchor plate in both directions as
you add more concrete.
• Slope the top of the concrete ll away from the ground
anchor in all directions to shed moisture away.
TIME OUT TIP: If you must adjust the height,
be sure to re-check level and that the anchor is
parallel with playing surface!
Step 8: If needed, adjust anchor plate height. The top
of the ground anchor should be within a range of 1”- 3”(25-75 mm) above
playing surface. Be sure to re-check level.
Step 1: Locate and unpack a 6” ground anchor (Item
G2660). Remove plastic plugs from bolt holes and ensure the threads are
in good condition. REPLACE THE PLUGS – they will keep concrete and debris
from the bolt holes during installation. Leave the hinge pin in place as well.
Step 2: Determine hole location. When installed, the edge of
the ground anchor must be a minimum of 6”(15.2 cm) away from the playing
surface. Follow One Call or your utility’s recommendations as to how close you
may dig to a marked utility.
IMPORTANT
You MUST dig the anchor hole at least 48”(1.2 m) deep.
WARNING
Before digging for the ground anchor, check for underground power, gas,
telephone, water and other utility lines. Failure to do so could result in serious
injury. See 811 One CallWarning box on page 2 for more information or call
your local utility company.
Step 3: Dig hole 48”to 50”(1.2 m – 1.3 m) deep and 18”
(0.5 m) in diameter using a spade, shovel, auger or post hole digger.
TIME OUT TIP:
If you plan on mixing concrete in
stages, work quickly to minimize time between batches.
Step 4: Mix concrete. Put concrete in wheelbarrow. Add the amount
of water recommended on the bag, and mix with hoe.
Step 5: Begin adding concrete into hole until concrete is
approximately 28”- 30”(.7 m – .8 m) deep.
1”- 3” (25-75 mm) minimum
16-18”
(0.41-0.5 m)
6" (152 mm)
all sides
Playing
Surface
42”
(1.1 m)
6” (152 mm)
48-50”
(1.2-1.3 m)
6" (152 mm)
minimum AND
parallel
Playing Surface
Check level both
directions
Ground Anchor Installation

5
HARDWARE:
Pole Assembly
IMPORTANT
• Allow 48 hours for concrete to cure before beginning.
• Check to see that no concrete or debris obstructs threads in ground
anchor bolt holes by threading anchor bolts in & out.
Step 1: Remove ve plastic plugs from threaded
holes in ground anchor. Also remove hinge pin and hex nut and
place near anchor plate. (These will be used in Step 3.)
TIME OUT TIP: To protect pole nish, place square
packing pad (included in pole box) on the ground
at the bottom of pole. Remove once pole is held by
installation clip.
Step 2: Unpack pole and jack. Jack comes packaged with the pole.
Jack will be used in Jack Attachment instructions.
Step 3: Align pole hinge with anchor plate hinge, then
insert hinge pin and hand tighten hex nut.
Step 4: Lift pole to approximately 30º and attach
installation clip to ground anchor and pole to maintain the
installation angle.
IMPORTANT
The installation clip MUST remain in place until pole is raised in Goal
Alignment, page 9.
WARNING
Two or three people in good physical condition and capable of lifting at
least 90-100 lbs. (40-45 kg) each are recommended for safe installation
and assembly.
3/8”x 7”Hinge Pin (1) 3/8”Hex Nut (1)
1/2 x 11/4”
Anchor Bolt (1-black)
Step 4
Step 3
Installation
Clip
Hinge
Pin
Hex
Nut

6
Step 3: Align and attach upper extension arm pivot
holes with upper bushing on pole following the same
hardware and procedure as in Step 2.
Step 4: Remove protective material from
extension arms.
Extension Arm Attachments
WARNING
Two or three people in good physical condition and capable of lifting at
least 90-100 lbs. (40-45 kg) each are recommended for safe installation
and assembly.
TIME OUT TIP: The lower extension arm is the
longer of the two arms.
Step 1: Unpack extension arms. Align lower extension arm
pivot holes with lower bushing on pole.
Step 2: Attach lower extension arm pivot holes with
lower bushing on pole using the following: one 1/2”x 11”bolt, two
at washers, four nylon washers and a locknut.Tighten with 3/4”wrench and
socket so the bushings on the extension arm meet the bushing on the pole.
Do not over-tighten.
1/2” Nylon
Washer (8)
1/2” Flat
Washer (4)
HARDWARE:
TOOLS:
Rubber Mallet, 3/4” Socket, 3/4”Wrench
1/2” Locknut
(2)
1/2” x 11”Extension Arm Bolt (2)
Step 3
Lower
Extension
Arm
Upper
Extension
Arm
Flat
Washer
Nylon
Washer
Lock
Nut
Step 2
Extension
Arm Bolt
Flat
Washer
Nylon
Washer
Flat
Washer
Nylon
Washer
Lock
Nut
Flat
Washer
Nylon
Washer

7
Step 3: Extend jack by turning jack handle counter-
clockwise until upper jack bracket is aligned with holes in lower
extension arm.
IMPORTANT
Attach upper end of jack to lower extension arm by extending the jack; DO
NOT swing arm to make the attachment.
Step 4: Attach upper end of jack to lower extension
arm using the following: one upper jack pole bolt, two at washers, two
nylon washers, two spacers and a locknut. Tighten with a 3/4”wrench and
socket. NOTE: DO NOT over-tighten. Snug tighten only.
Jack Attachment
WARNING
Two or three people in good physical condition and capable of lifting at
least 90-100 lbs. (40-45 kg) each are recommended for safe installation
and assembly.
IMPORTANT
The jack is packaged with the pole.
Step 1: Unpack the jack.
Step 2: Attach lower end of jack to bracket on pole
using one lower jack pole bolt, two at washers, four nylon washers and a
locknut.Tighten with a 3/4”wrench and socket.
NOTE: DO NOT over-tighten. Snug tighten only.
HARDWARE:
TOOLS:
3/4” Socket, 3/4” Wrench
1/2” Nylon
Washer (6)
1/2” Flat
Washer (4) 1/2” Locknut (2) 1” Spacer (2)
Step 2
Lower
Extension
Arm
Upper
Extension
Arm
Step 4
Locknut
Flat
Washer
Upper Jack
Pole Bolt
Lower Jack
Pole Bolt
Nylon
Washer
Spacer
Step 3
Flat
Washer
Nylon Washer
Flat
Washer Flat
Washer
Locknut
1/2” x 11”Upper Jack Pole Bolt (1) 1/2” x 4” Lower Jack Pole Bolt (1)

Backboard
Bolt
Backboard
Bolt
Flat
Washer
Flat
Washer
Step 3
Locknut
Flat
Washer
Flat
Washer
Locknut
Flat
Washer
Backboard
Bolt
Flat
Washer
Step 2
8
WARNING
Two or three people in good physical condition and capable of lifting at
least 90-100 lbs. (40-45 kg) each are recommended for safe installation
and assembly.
IMPORTANT
The installation clip MUST be in place to maintain the proper
installation angle.
TIME OUT TIP: Lay the unopened box with
Leisure Time Products logo upside down AND let the lid
open up and fold away from the goal system.
Step 1: Open lid of box containing backboard and slide
the backboard face down under lower extension arm, with rim mounting plate
facing towards goal system.
TIME OUT TIP: The backboard attachment can be
eased by cranking the jack to help align lower
extension arms above the backboard prior to lifting it.
Backboard Attachment
Step 2: Carefully lift the bottom of the backboard to
align lower backboard holes with lower extension
arm holes. Using ratchet and wrench, attach backboard to arm using the
following hardware: two backboard bolts, four at washers and two locknuts.
NOTE: This is a pivot point! DO NOT over-tighten. Snug tighten only.
Step 3: Lift top of backboard to align upper holes
with upper extension arm holes using the same hardware and
procedure as in Step 2.
1/2” Locknut (4)
1/2x 31/4”
Backboard Bolt (4) 1/2” Flat Washer (8)
HARDWARE:
TOOLS:
3/4” Socket, 3/4”Wrench

WARNING!
For safe assembly, do the following:
• Use two or three people to raise goal assembly and hold it in a vertical
position. Two or three people in good physical condition and capable of
lifting at least 90-100 lbs. (40-45 kg) each are recommended for safe
installation and assembly.
• DO NOT adjust height of backboard or attach rim until pole is raised and
appropriately bolted.
• Correct sequence of hardware installation MUST be followed during
assembly.
To avoid injury, keep ngers and toes away from the ground plate while
raising the goal assembly to the vertical position.
Step 1: Remove banding and edge protection from
backboard. Peel back TOP 1/3of protective sheeting from the backboard.
This will allow you to reach the sheeting once goal has been raised, yet
protects the surface of the backboard during installation.
Step 2: Locate ve anchor bolts. Prepare them for use by
having lock washers slipped on and placed near ground anchor.
Step 3: Using at least two people, carefully push
up on backboard to raise goal assembly to vertical
position. The installation clip will fall away. Save installation clip for
future disassembly.
9
Step 4: Fasten pole to threaded ground anchor plate
by installing and hand tightening the three rear anchor bolts with lock washers.
Step 5: Fasten pole to threaded ground anchor plate
by installing and hand tightening the two front anchor bolts with lock washers.
TIME OUT TIP: Install rear three anchor bolts rst
and then the front two anchor bolts.
Step 6: Snug tighten the ve anchor bolts, then check
goal assembly with a level and inspect visually to
determine if it is parallel and plumb to the playing surface.
Step 7: If adjustments are necessary, slightly loosen bolts to
rotate goal.
Step 8: Fully tighten ve bolts using a 3/4”socket with a torque
wrench.The torque wrench is to be set at 75 ft/lb on dry threads and 55 ft/lb
on lubricated threads. NOTE: The anchor plate is threaded, so there is no need
to use nuts on bolts.
IMPORTANT
The bolts must pass all the way through the ground anchor plate. If they
do not pass through the ground anchor plate when fully tightened, STOP
installation, contact LeisureTime Products and DO NOT allow play.
Goal Alignment
Step 3
PlayingSurface
Step 4
Step 5
Lock
Washer
Anchor
Bolt
Ground
Anchor Plate
1/2 x 11/4”
Anchor Bolt (5-black)
1/2” Lock
Washer (5)
HARDWARE:
TOOLS:
3/4” Socket, Level, 1/2” Drive Torque Wrench
End of anchor bolt should
extend 1/8”below anchor plate.

Step 3
Step 4
Flat
Washer
Flat
Washer
Flat
Washer
Backboard
Bolt
Backboard
Bolt
Lock
Washer Nut
Rim Attachment
NOTE: Use all steps of the following instructions to install a reex rim.To
install a static rim, follow all steps except Steps 2 and 6.
TIME OUT TIP: Your warranty card is located
behind protective sheeting.You MUST complete
and ll out this card to activate your warranty.
Step 1: Unpack rim. Remove any remaining cardboard edge
protectors and protective sheeting from backboard.
IMPORTANT
• Four bushings are factory installed on the backboard. If loose, make sure
to have them seated properly when tightening rim bolts. If missing,
contact Leisure Time Products or dealer.
DO NOT install rim without bushings. If the bushings are not
in place, glass backboards can shatter and acrylic backboards
can crack!
• Correct sequence of hardware installation MUST be followed
during assembly.
Step 2: If not already removed, remove cover plate
screws and cover plate from rim assembly.
Step 3: Starting with the top two mounting holes,
loosely attach rim to backboard following the
hardware sequence as shown in the illustration below. Snug tighten
hardware - a
9/16”open-end wrench may be necessary.
Step 4: Repeat hardware sequence outlined in Step 3
for lower rim mounting holes.
Step 5: Level rim side to side and then fully tighten
hardware.
Step 6: Position cover plate and attach with cover
plate screws.
Step 7: Attach net to rim.
3/8x 2”
Backboard Bolt (4) 3/8” Flat Washer (8) 3/8” Lock Washer (4) 3/8” Nut (4)
Cover Plate
Screw (4)
Step 6
Cover Plate
Screw
Cover Plate
Screw
Cover
Plate
HARDWARE:
TOOLS:
Level, 9/16”Wrench, 9/16”Socket, Phillips Screwdriver
10
Factory Installed Bushing
(Backboard damage can result if not installed)
TIME OUT TIP: Level rim side to side
before tightening backboard bolts.

11
Height Indicator Attachment
8
7
7
1
/
2
Step 1
Step 3
TOOLS:
12’Tape Measure
DECAL:
Step 1: Position top of rim 7’above playing surface by turning crank handle.
Step 2: Draw a mark on inner tube at edge of outer jack tube.
Step 3: Extend jack approximately ½”. Peel ½” of backing o the top of
the decal (by the 7’mark). Slip decal under the outer tube on the jack until
the 7’line is even with the drawn mark.
Step 4: Hold decal square with the jack and peel
backing o, pressing decal down onto jack as backing
is peeled o.
7’

12
Goal Assembly, cont.
Operation
Crank handle turns clockwise for goal
to go up, crank handle turns counter
clockwise for goal to go down.
Height indicator indicates goal height
from 7’to 10’.
To prevent undesired height
adjustment, remove crank pin and
crank handle.
Maintenance
The life of your basketball goal system depends on many variables. The climate,
exposure to corrosives such as salt, organic materials, pesticides, or herbicides,
and excessive use or misuse can all contribute to failure of the goal system, which
may cause property damage or personal injury. Before each use, check the goal
system for loose hardware, excessive wear, abuse, or vandalism or signs of rust or
corrosion.
For safety reasons, and to prolong the life of your basketball system, you must take
the following preventative measures:
• Check all nuts and bolts. Inspect the threads and replace if necessary. If any are
loose, tighten them.
• Check all parts for excessive wear and tear. If necessary, replace any parts that
have been worn or damaged through usage.
• Check all sections of the goal system for visible rust or chipped or cracked paint,
and if present, repair appropriately. See Paint Touch-Up on this page.
IF RUST OR CORROSION HAS PENETRATED ANY COMPONENT, DO NOT ALLOW
PLAY ON THE GOAL AND REPLACE PARTS IMMEDIATELY.
• Contact Leisure Time Products for replacement parts. Only use parts provided by
Leisure Time Products Use of other parts (a) may cause the goal system to fail,
(b) could result in death, serious injury or property damage, and (c) will void the
warranty.
• Inspect the Warning Sticker on the pole. If it is ripped, faded, or illegible, contact
Leisure Time Products to request a replacement Warning Sticker.
Cleaning
The exterior nish of your LeisureTime Productsgoal is designed for outdoor
environments and should only require periodic cleaning and inspection for
imperfections that could develop over time.
When cleaning is necessary, LeisureTime Products recommends using water
and a mild dish detergent applied with a soft, non-abrasive cloth.
IMPORTANT
DO NOT use abrasive cleaners to clean the goal. Damage to the nish
may result.
Paint Touch-Up
Leisure Time Products uses a two-part acrylic-
enamel paint on the goals.With periodic inspection and
service when needed, the high-gloss nish is designed to
last for many years. A small bottle of black paint with brush
is provided in the hardware kit for touch up of imperfections
as they develop. If more touch up is required, please contact
Leisure Time Products or your local dealer.
Lubrication
The jack is pre-lubricated. As with any mechanical component, periodic
inspection and service is required. Leisure Time Products recommends
applying lubrication each spring and fall to keep a smooth operation of the
height actuator. Failure to do so could result in jack failure and not be covered
under warranty.
Remove lubrication panel and apply a liberal amount of lubricating oil to the
thrust bearing and jack screw.
Ready to Play
8
7
71/2
Lubrication Panel

13
Warranties
IMPORTANT
Enclosed underneath the protective sheeting on your backboard is a
warranty registration card. YOU MUST FILL OUT AND MAIL IN THIS
CARD IN ORDER TO HAVE A VALID WARRANTY.
LIMITED WARRANTY
LIMITED LIFETIME WARRANTY: Subject to proper installation and
normal, intended use, and subject to the limitations set forth below, Leisure
Time Products warrants to the original retail purchaser that all structural
components of Leisure Time Products LT PRO Series basketball systems are
free of defects in material and workmanship for the duration of ownership
by such original retail purchaser or ve (5) years after discontinuation of the
product by LeisureTime Products.
LT PRO Series – LTP672, LTP560, LTP454;
Any warranty on a basketball system excludes the rim. Rim warranties are
as follows: Rims shall be free from defects in materials and workmanship
from the date of purchase as follows: R10326 Heavy Duty Breakaway Rim:
two (2) year limited warranty.
Padding Warranty: Padding shall be free from defects in materials
and workmanship from the date of purchase as follows: Multi-Purpose
Backboard Edge Padding: one-year limited warranty; Wrap Around Pole
Padding: one-year limited warranty.
The Limited Lifetime Warranty and the Limited Warranty shall cover
damage or failure that occurs during the course of NORMAL or INTENDED
USE of the product. Normal or intended use shall be described as activity
that is necessary for the participation in the sport for which the equipment
is designed. NOT COVERED is damage caused by deliberate hanging,
multiple player hanging, vandalism, non-basketball activities or any other
activity that could be regarded as abusive.
A limited lifetime warranty is eective for the duration of ownership by the
original retail purchaser or 5 years after discontinuation of the product by
Leisure Time Products.
Leisure Time Products shall have the right to require the purchaser to
deliver at its expense the allegedly defective product to Leisure Time
Products for testing, repair or replacement. Leisure Time Products shall
not be responsible for any expenses associated with the replacement or
removal of the product from its application for such delivery.
THEWARRANTY IS VOID IFTHE PRODUCT HAS BEEN DAMAGED BY ACCIDENT,
USE FOR PURPOSES FOR WHICH IT IS NOT INTENDED, AS THE RESULT OF
IMPROPER INSTALLATION, FAILURE TO FOLLOW INSTALLATION, CARE OR
MAINTENANCE INSTRUCTIONS PROVIDED WITH THE PRODUCT, USE OF
PARTS NOT PROVIDED BY LEISURE TIME PRODUCTS OR ANY MODIFICATION
OF ANY PRODUCT BY THE CUSTOMER UNLESS APPROVED BY LEISURE TIME
PRODUCTS, OR OTHER CAUSES NOT ARISING OUT OF DEFECTS IN MATERIALS
OR WORKMANSHIP.
The sole obligation of Leisure Time Products, and the exclusive remedy
under the applicable warranty, is repair or replacement of any component
part determined by Leisure Time Products to be defective and covered
by the warranty. Leisure Time Products will not be liable for any other
damages or expenses. The applicable warranty is expressly in lieu of all
other warranties, express or implied. Leisure Time Products does not
assume, and no other person or representative is authorized to assume
for Leisure Time Products any other liability in connection with the sale of
Leisure Time Products, products.
NOT COVERED BY WARRANTY
• Use in non-residential applications of LT PRO Series and Elite complete
systems.
• Any products subjected to abuse, negligence, improper installation,
vandalism, acts of God, alteration of product and any other events beyond
the control of Leisure Time Products
• Paint or rusted parts. Touch-up paint is included in all hardware kits.
• Deterioration of product due to time or wear and tear.
Normal deterioration of products due to atmospheric conditions, weather,
wear and tear (including scratching or scung paint from normal use), or
other causes that do not aect functional use are not covered by Leisure
Time Products warranties. All warranties are valid only when product is
used in the intended application & when installed according to LeisureTime
Products instructions. Warranty may be void if maintenance instructions
in the Owner’s Manual are not followed. If you did not receive an Owner’s
Manual, please call 1-800-856-4445 and one will be mailed to you.
DISCLAIMERS: THE APPLICABLE WARRANTY IS EXPRESSLY IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED. AND ALL OTHER WARRANTIES
ARE HEREBY DISCLAIMED, INCLUDING BUT NOT LIMITED TO THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. UNDER NO CIRCUMSTANCES SHALL LEISURE TIME PRODUCTS
BE LIABLE FOR ANY INDIRECT, CONSEQUENTIAL, SPECIAL, INCIDENTAL,
PUNITIVE, OR EXEMPLARY DAMAGES OF ANY KIND.
THE PRODUCT IS INTENDEDTO BE USEDTO PLAYTHE SPORT OF BASKETBALL.
ALL SPORTS INVOLVE RISK OF INJURY. THE USER ASSUMES ALL RISK OF
INJURY RESULTING FROM THE USE OF THIS PRODUCT. ALL PRODUCTS ARE

SOLD ON THIS CONDITION AND NO REPRESENTATIVE OF THE COMPANY MAY
WAIVE OR CHANGE THIS POLICY.
Some states do not allow the exclusion or limitation of implied warranties
or consequential or incidental damages, so the above limitations or
exclusions may not apply to you.
LEGAL REMEDIES: This warranty gives you speci c legal rights, and you
may also have other rights which may vary from state to state.
WARRANTYCLAIMS:AllreturnsmustbearrangedthroughtheLeisureTime
Products dealer where the product was originally purchased. Warranties
do not cover dealer service charges, labor charges, freight charges, and
travel expenses associated with replacement, repair or removal of warranty
items. Photos of the damaged product prior to any repair or clean-up
actions must clearly show and permit analysis of the damaged product
by Leisure Time Products. Photos must be submitted, together with proof
of purchase, for any item you wish to claim under warranty. In response
to your claim, you will receive an order con rmation as well as a notice
stating whether LeisureTime Products needs your warranty item returned.
Leisure Time Products will notify you if we determine that the item cannot
be claimed under warranty. Leisure Time Products is not responsible for
any charges for labor to install or repair defective product without prior
authorization. Leisure Time Products will determine the most economical
method to either repair or replace product before any work is to commence.
Questions or Comments?
Phone [phone]
LEISURE TIME PRODUCTS® and LEISURE TIME PRODUCTS logo are
registered trademarks of Leisure Time Products in the United States.
No part of this manual may be reproduced in any form or by any
means electronic or mechanical, including photocopying, recording, or
by any information storage and retrieval systems without the express
written consent of Leisure Time Products.
Copyright 2015.
All rights reserved.
Revised 1/2015.
14

15
Notes

Phone [phone]
1/2015