Lenovo A680 User manual



GPS tracker user manual
For Watches style and Hanging style
I、Key Definition
ON / OFF
USB Port
Call / Answer / SOS
Pre-set Call 1
Pre-set Call 2 guardian
Pre-set Call 3
II、Specification
GPSlocationaccuracy15M
GSMNetworkaccuracy200M
GPSBand1575MHz
GSMBand850/900/1800/1900MHz
DisplaySize1.44TFT
Standbyconsumption1to3mA
GPSconnecting70mA
Standbytime7days
Continuousmonitoring8‐10hours
Battery600‐750mAhHiLi‐ionrechargeablebattery(750mAhForWatchestyle)
Hotstarttimeabout3seconds
Warmstarttimeabout15seconds
Coldstarttime<60s(Autonomous)
Workingtemperature‐20°Cto65°C
Workinghumidity5%to95%
Storagetemperature‐45°Cto+90°C
Restrictiveworkingtemp≤‐40°Cor≥+80°C
Display icon
GPS on, positioning.
GPS on, not yet position.
Management platform turn on. The device connecting
the platform through GPRS network, the platform can
send commands to the tracking device.
Device sending position information to the platform.
Tracking record turn on.
Quiet mode turn on.
Allows only incoming preset number
Closes the GPS localization pattern
III、Operation
1. Turn on



Press and hold the key till it shows the turn on Logo, then it will enter the main interface and show
me ,date automatically.the current ti
2.
When stand by, press and hold the key
Turn off
to turn off. The operation will be finished after displaying
image shutdown.
3. SOS signals
When the tracker standby ( with SIM card): press and hold the key for 3 seconds, the tracker will
shock for once indicating to enter “one press help” mode, then it will send message to the preset
wed by dialing guardian,SOS1, SOS2, SOS3 numbers, after then it will go to the listening
atically.
numbers follo
status autom
4.
hold the key
Call out
W he tracker standby, it call out the pre-set numbers by press andhen t can ,
or respectively. The key is the main controller /guardian number.
5. Phone numbers Pr
Please e-set
set guardian numbers by referring to the setup instructions in appendix “ V ”.
6.
zGPS tracker r nd vibrates when a call comes in, the LCD screen will show the caller's phone
me.
Calls ings a
number and ti
zPress the key onc eceive the call.e to r
zPress the key or to reject the call.
zThe missed call will be displayed on the LCD interface ..
7. Missed call nsw splayed.
l, press
zAny missed call or call failed to a er will be di
zTo check the missed cal to read it
8. th auto hands-free function. When the headset be connected, it will change the
dset tically, and reminding will be displayed if the ction is corrected.
Hand-free function
The tracker device wi
output mode to the hea automa conne
9.
While talking, press the key
Volume adjustment
to increase the call volume, or press the key to decrease the call
volume.
10. GPS time
zGPS tracker will turn to GPS function when it boot. It will correct and update the time and date.



zWhen power on, press to select the GPS functions (positioning status, latitude, longitude,
altitude, speed ion). Then the tracker will turn on the GPS function automatically., direct
IV、Monitory function
Press the key to enter the function menu interface, there are som functions :e
1.
Press the key
Message: To check message received.
once to enter the function menu interface, press to sele essage.If there’s
list i
stored with 19 messages. If a new message comes in, the first message will be deleted automatically.
ct the m
no message, the screen will be blank; if with message, it will enter the message nterface. It can be
2. Weather: To view the current location weather rmation. Press the keyinfo essage
will be displayed. Shortcuts: Main interface buttons
and the m
.
3. My position: To view the current geographic location information. Press the key and the
ttons
message will be displayed. Shortcuts: Main interface bu .
4. Language: Set the display language.
5. Time setting: Set the time zone, daylight saving time.
Alarm: Set alarm.6.
GPS Status: Check current location’s GPS satellite signal searching strength.7.
Press the key to enter the function menu interface, press to select GPS status, enter the GPS
Inte
satellite searching mode interface, if GPS is in normal, and also in the GPS signal covered area, LCD
screen will display the status diagram of the satellite and satellite signal strength.
rface indication
The white c density of the signals.
When lower other Spacious place.
Usually the s
haracters stand for the number of satellites. Green ones stand for the
than 30, it means the signals are too weak, please move to some
atellites density will not over 50. It’s shown as below:
GPS Info: When power on, press the key to enter the function menu interface c, then8. hoose the



de, altitude, speed, direction). The tracker will turn toGPS function (positioning status, latitude, longitu
the GPS function. It will correct and update the time. Shortcuts: Main interface buttons .
Others: The IMEI numbers, software version and battery status of the tracker.9.
V、Mobile control and command setting
Notes: g
et
The followin setup instruction can be applies to all mobile phone only before the guardian number
not be s .Sneed to increase password and
Type Command Instruction
uch as the their privacy, please change the initial
set guardians number. Function Remarks
Set guardian 11# mobile phone number bers, The initial password is 0000.
numbers # password Set guardian num
Set SOS numbers 12# sos1# sos2 Example: You can set 2 SOS numbers :
12#12345678910#12345678911
Password 13#old password #
new password
Example: changed the password to 1234
13#0000#1234
Password: The acquiesced password is 0000.If forget new
p
assword a er modifying, just connft ect computer with USB
cable to check the password.txt file and find it out.
School quiet mode14#1 （Open）
14#0 （OFF Default）From 8:00-11:30; 14:00-17:30, the tracker refuse all incoming
calls except SOS numbers and the guardian numbers. LCD
displaying to ensure wit quh iet.
GPS mode 15#1 （Open Default）
15#0 （OFF）The device default GPS + LBS dual positionin
g
functions.
When the o
p sitionin
g
accuracy is not the case, tu
GPS positionin rn off the
g
mode can si
g
nificantly extend the standby
time! and LCD displaying .
Call Management16#0 （OFF）
16#1 （Open Default）
lls LCD
16#0 Only authorized number to answer ca
displaying
16#1 Allow incoming calls to all numbers
Set class
factory settings 0000 Recover factory setting : 0000
Search Location
（txt）21
Search for GPS tracker’s current location information.
It can also be achieved by dialing the numbers to the GPS
tracker: If dial the numbers and hang up within 5 seconds, the
GPS tracker does not display incoming call, but sends a message
to the caller. If over 5 seconds, the GPS tracker displays
to the caller
incoming call, then also send the current location
automatically.
Search Location
（Map）22 location information and reply
Search for GPS tracker’s current
website link.
Set of query 25 Queries the current setting state of GPS Tracker
Search for classes
Balance of query 36 GPS tracker card balance inquiry
This’s for mainland China only.



Track record set
24#0 （Tracking off）
24#60 (Tracking open）
24## （Delete）
24#60 (Default)（60 means 60 Mins）(from 1-99 mins).
Turn it on to set time (unit: minute); interval tracking record will
be uploaded to the management platform. The LCD displays
to show tracking record is on. The tracing data
Will be stored nto the platform. The historical track can be
viewed on the platform too. To save power,just turn off i
i
f
p
latform connection no longer need.
Internet access
point settings assword
32# Access Point
# User name # p
32#cmnet##
Set the GPS tracker to access the network through cmnet access
p
oint. Usually the user name and password are not needed to fill
et; China
pccw
and let it blank. For example: China Mobile: cmn
Unicom: uniwap; PCCW :
Mana
Platform setting
34#1 （Open Default）
gement 34#0 （OFF）
LCD display to show the management platform open, the
terminal connecting through the GPRS network, then the
p
latform can send commands to the GPS tracking device.To
ed.
save power,just turn off if platform connection no longer ne
Advanced Settings command
）To forward the received SMS to the guardian mobile phone.
( messages from the guardian excluded)
or guardian in mainland China only.
SMS forward 35#0 （OFF Default
settings 35#1 （open）This’s available f
Phone monitory
settings 23# Number
23# Ask for dialing back.
23#12345678910
Monitor number refers to the number which the tracker diale
d
back; It can be a mobile phone or non-mobile.
zThe above details for reference only, we reserve the rights to make amendment without prior notice.
zAll copyright are reserved.
P.S :
For change the Time Zone of 13, the command is :
31#01300#0