LG JMC8130DDS User manual

il_ €11 r,__IV,2i e
il_ II ._'!_e_ll e_ Built-in 27" & 30"
Microwave Ovens 403 WEST FOURTH STREET, NORTH l
J
NEWTON, IA 50208
WARNING
Improperinstallationof the grounding
circuit can result in a risk of electric
shock.
:{I]di _v_I[_] :{olV_Vl;Vj =l[olv/= _im]=[-"[_]:t IM I [el _i
1 Properly Polarized and Grounding Outlet.
2 518" Plywood Floor (Must Support 100 Ibs.)
3 About 15-7/8 Inches
4 About 1-3/8 inches
inches Centimeters
A 27 MIN 68.58 MIN
B 24 MIN 60.96 MIN
C 22-5/8 + 1/16 57.47 +0.16
D 24 MIN 60.96 MIN
E 25-1/2 + 1/16 64.77 +0.16
F 23-7/16 59.69
G 26-3/4 67.95
H 20-3/16 51.27
inches Centimeters
A 30 MIN 76.2 MIN
B 24 MIN 60.96 MIN
C 22-5/8 + 1/16 57.47 +0.16
D 24 MIN 60.96 MIN
E 28-1/2 + 1/16 72.39 +0.16
F 23-7116 59.69
G 29-3/4 75.56
H 20-3116 51.27
MICROWAVE OVEN CUTOUT
C
CAUTION
For European style cabinets (flush front)
the required clearance for operation of
the oven door is minimum spacing of
7/8" between the cutout and the door,
hinge or drawer of the cabinet. Some
built-in cabinets may not be wide
enough, due to their construction, to
allow this installation.
8101 P504-60
3828W5U0230 (05-03-02)

INSTALLATION
1. Cut hole in cabinet to mount Microwave oven. Cutout in
cabinet should be level and straight.
NOTE: There are no provisions to level the unit after it
is installed. An oven that is not level could cause poor
cooking results.
2. Install plywood floor as shown above.
3. Attach unit to the cabinet with 4 long oval head screws
supplied inside of envelope containing these
instructions. Pre-drill 4 holes in cabinet for attachment
screws using 1/16" drill. Oven mounting holes are
provided in side trim.
4. Attach the bottom grill, found in the upper packing
materials, to the front plate with the 2 short truss head
screws supplied in the envelope packaged with the
bottom grill.
5. See Owner's Manual for operating instructions.
NOTES
• Do not build in above gas wall ovens due to placement
of gas wall oven vent.
Electrical rating of this oven:
• 120 VAC @ 60 Hz.
• 13A/1000 W
• You need a DEDICATED 120 VAC, 60 Hz, 15 A or 20
A, fused electrical supply (located in the cabinet with
the microwave as close as possible to the microwave)
serving only the microwave.
• Check with a qualified electrician if you are not sure
whether the oven is properly grounded or if you do not
completely understand the grounding instructions.
• Do not use a fuse in the neutral or grounding circuit.
• Save these instructions for the local electrical
inspector's use.
• If there is an electrical short circuit, grounding reduces
the risk of electrical shock by providing an escape wire
for the electric current. This appliance is equipped with
a cord having a grounding wire with a grounding plug.
• Place the plug into a properly installed and grounded
outlet.
•Maytag does not recommend use of an extension
cord.
• Keep the power cord dry and do not pinch or crush it.
• Do not, under any circumstances, remove the power
supply cord grounding prong!
• This appliance MUST be grounded!
SERVICE
Interrupt the source of electricity to the unit when attempting
to repair or service the oven. Failure to do this could result
in a dangerous or even fatal shock.
28 1/2"
-- CUTDUT --
WII]TII
22 518 _
MICROWAVE
CUTOUT 1° GAP
i r 3ETWEEN
i _ culUUIS
29 i/8"
30" SINGLE
CUTDUT
2" GAP
BETVEEN
CUTOUTS
9 t/4" _ I
_ARM]N5 I)RhWER
CUTOUT { f :
7
DIN "A"
[
Dim "A" = With Warming Drawer = 69" 1
Dim "A" = Without Warming Drawer = 59'/4"
22 5/8"
MZC_Q%VAVE
CUTOUT 1' GAP
i ZTVEEN
CUlUU_S
t
!
i
22 5f8'
CB_ 'lENIENCE
_U1EItJ_ _ G_P
I I......
CUTOUT_
9 _4 _ _
'#ARMINGctjT_t)TDRA_ERI" 4_ _
l'J
1
28 1/5"
--CUTCUT .....
WIDTH
I
Dim "A" = With Warming Drawer = 62½"
Dim "A" = Without Warming Drawer = 59¼"
1
22 5/8"
MI[:R[IWAV_
CUTOUT
ii..GA.
BET'WEEN
CUTOUTS
91+/4,i
VARMING _RAWER
CUTiUT
21 3/8"
2B 1/5'
-- CdTB/_ --
WIDTH
SAME FOR BOTH WITH OR WITHOUT
WARMING DRAWER
Unit approved for use over the following wall ovens:
JJW9530D JJW9527D JJW7530DD
JJW8530D JJW8527D JWD7030CDX