Liberty garden Liberty basics 512 User manual

VISIT OUR WEBSITE: WWW.LIBERTYGARDENPRODUCTS.COM

OR CALL US TOLL FREE AT 1-866-820-5805

IMPORTANT: READ THE OWNER’S MANUAL BEFORE ASSEMBLING

LIBERTY GARDEN PRODUCTS, INC.

1161 SOUTH PARK DRIVE, KERNERSVILLE NC 27284

Wall Mounted Hose Reel with Shelf

Owner’s Manual

Model #512

™

b a sics

Holds 225 ft. of 5/8” Hose

PRE-ASSEMBLY Estimated Assembly Time : 10 minutes (not including mounting the hose reel)

PARTS LIST

A. Cross Brace (2) B. Left Reel Side (1) C. Right Reel Side (1) D. Exit Tube (1) E. Side Frame (2)

F. Lower Frame Bar (1) G. Upper Frame Bar (1) H. Crank Handle (1) I. Supply Tube (1)

J. C-Shaped Lock (1) K. Lubricant Tube (1) L. Shelf (1) M. Leader Hose (1)

N. Cross Brace Screw (4)

NOTE: Crank handle

can be applied on left

or right side of reel.

(See Step 3)

IMPORTANT: LAY OUT ALL PARTS AND FASTENERS. MAKE SURE ALL PARTS ARE ACCOUNTED FOR.

IF ANY PART IS MISSING PLEASE CONTACT LIBERTY GARDEN PRODUCTS AT 1-866-820-5805.

DO NOT CONTACT THE RETAILER. VISIT OUR WEBSITE, WWW.LIBERTYGARDENPRODUCTS.COM

OR E-MAIL CUSTOMERSERVICE@LIBERTYGARDEN PRODUCTS.COM FOR MORE INSTRUCTIONS.

Stamped Logo

TOOLS REQUIRED:

Stud

Finder

Hammer

Drill

Electric

Drill

Screwdriver

or bit for an

electric drill

HARDWARE INCLUDED

AA. Wood Screw (4)

Note: Hardware not shown to actual size.

Adjustable

Wrench

BB. Wall Anchor (4)

INSTALLATION This hose reel must be mounted to a solid masonry wall or to wall studs.

Tip: Remember to use the correct size and quantity of hardware to support the total weight of the unit. A standard 100’

length of garden hose weighs approximately 15 lbs. Filled with water, the additional weight can exceed 20 lbs. The

mounting hardware must be able to support the combined weight of the unit, garden hose, plus water.

1. WOOD SCREWS

The following hardware is included:

(4) 7 or 8 mm x 60 mm wood screws (AA)

(5/16” x 2 1/2”).

• Using a stud finder, locate wood studs on your wall.

• Position and hold the hose reel assembly against

the wall. Mark the positions of the suspension holes

and remove the reel assembly.

NOTE: Ensure the leader hose (M) will reach the

water supply reel.

If applicable, drill (4) 5/16” diameter holes and insert

(4) anchors (BB) into the drywall or masonite.

• Using a screwdriver, insert two wood screws (AA)

half way into the top two pilot holes or optional wall

anchors (BB).

• Mount the reel assembly on the top wood screws

(AA), install the bottom screws (AA) and tighten all

four screws. Do not overtighten the screws.

• Using an electric drill, drill (4) 1/4” diameter pilot

holes at the marked positions on the wall.

2. BRICK OR MASONRY SCREWS (Optional

Mounting Method)

The following hardware is not included:

(4) 7 or 8 mm x 60 mm masonry screws (CC)

(5/16” x 2 1/2”).

• Position and hold the hose reel assembly against

the brick wall. Mark the positions of the suspension

holes and remove the reel assembly.

NOTE: Ensure the leader hose (M) will reach the

water supply reel.

• Using a hammer drill, drill (4) 1/4” diameter pilot

holes at the marked positions on the wall.

• Insert two masonry screws (CC) half way into the

top two pilot holes.

• Mount the reel assembly on the top masonry

screws (CC), install the bottom screws (CC) and

tighten all four screws. Do not overtighten the screws.

ASSEMBLY

NOTE: Most parts are assembled by locking tabs on

the mating parts. The locking tab must slide down

into the snap as shown in the figures below.

3. Press the exit tube (D) into the snaps on the right

or left reel side (B) as shown in the figure below.

2. Install the side frame (E) onto the upper and lower

frame bars (F) and (G) as shown.

4. Align cross brace (A) tabs with the left reel side

(B) and assemble as shown.

1. Align and slide the locking tab on lower frame bar

(F) with the snap on side frame (E) until an audible

click sound is heard. Repeat the same steps for

upper frame bar (G).

NOTE: When the mating surface tabs and snaps

are flush, the frame bars (F),(G) and side frames (E)

are locked together.

NOTE: To disassemble a lower frame bar from a

side frame, use a flat head screwdriver to press the

lock tab and slide the frame bar out of the snap.

Left

Handed

Crank

Right

Handed

Crank

NOTE:

Make sure

the exit

tube faces

down.

NOTE: Ensure the locking tabs and snaps engage

and an audible snap is heard when the frame bars

and side frame are assembled.

ASSEMBLY

6. Using two supplied cross brace screws (N) secure

cross brace (A) to the left and right reel sides (B)

and (C).

NOTE: Do not over tighten the cross brace screws.

9. Press the left and right side frames (E) flush

against the reel assembly before proceeding to the

next step.

7. Ensure the cross brace screws (N) secure both

cross braces (A) into the left and right reel sides (B)

and (C). See figure below for reference.

5. Align cross brace (A) tabs with right reel side (C)

and assemble as shown.

8. Place the frame on a sturdy surface and install the

reel asembly on the frame as shown in the figure

below.

NOTE: Flex the side frames (E) outward to enable

installation of the reel assembly.

ASSEMBLY

10. Using lubricant tube (K), lubricate the o-rings on

the supply tube (I).

11. Align the supply tube (I) tabs with the side frame

slots and push until the supply tube is fully inserted.

Ensure the supply tube tabs align with the slots in

the side frame during installation.

12. Align the c-shaped lock (J) with the slot in the

cross brace (A) and push until an audible snap is

heard.

15. Place crank handle (H) into the reel hub and

snap into place.

14. Align shelf (L) tabs with the side frame (E) slots on

each side and snap into position as shown below.

16. Mount hose reel assembly.

NOTE: See hose reel mounting instructions on

page 3 (Installation section) of this owners

manual.

13. Align the second cross brace (A) tabs with the

left and right reel sides (B) and (C), and assemble

as shown. Using two supplied cross brace screws

(N), secure cross brace (A) to reel sides (B) and

(C). Do not overtighten the cross brace screws.

ASSEMBLY

17. Connect Leader hose (M) to supply tube (I).

NOTE: Do not overtighten the leader hose.

18. Connect garden hose to the exit tube (D).

NOTE: Do not overtigthen the garden hose.

CARE AND MAINTENANCE

WINTERIZING AND STORAGE

Drain the hose reel prior to the onset of freezing temperatures. If any trapped water freezes, it may cause damage to the hose

reel, hose, and even your pipes.

Store the entire unit - including hose reel and hose - inside your garage or storage shed at above-freezing temperatures.

Storing your hose reel inside during the winter is an excellent way of protecting your garden hose, leader hose and O-Rings.

CALL US AT 1-866-820-5805 IF YOU HAVE ANY QUESTIONS

REGARDING CARE AND MAINTENANCE

When you install your hose reel, be sure the hose washers are in place and all fittings are secure. If you live in more temperate

climates, be sure to drain the unit of any residual water before storing.

• DO NOT EXPOSE UNIT TO FREEZING TEMPERATURES while water remains in the plumbing system, this can damage the

hose connections.

•DO NOT leave water running through the reel while not in use or unsupervised.

Your hose reel is manufactured with the finest quality components available. This product will give you many seasons of reliable

and functional hose storage. All components in the product are manufactured to rigorous quality standards not common in other

consumer grade hose reels available today. In the case of wall mounted reels, be sure to use stainless steel mounting hardware.

We recommend that you periodically inspect your reel for any surface damage. NOTE: Liberty Basic’s plastic hose reels use

ultraviolet light stabalizers in our plastic, but over time, the plastic color, depending on the amount of sunlight, can fade.

WARNING: DO NOT consume water from garden hose; not fit for human consumption.

WARNING: Cancer and Reproductive Harm

- www.p65warnings.ca.gov

NOTE: Check for leaks prior to mounting.

LIBERTY GARDEN PRODUCTS LIMITED WARRANTY

(Effective December 17, 2018)

This limited warranty is applicable to each original end-customer (hereinafter “Customer”) purchasing the model 512 wall mounted hose

reel with shelf.

1. LIMITED WARRANTY; EXCLUSIVE REMEDIES:

1.1. LIMITED WARRANTY ON PRODUCTS: Company warrants solely to the original Customer that (a) the Structural Frame will be free

from defects in materials and workmanship under normal use for a period of three (3) YEAR(S) from the date of original retail purchase, and (b)

the Non-Frame Parts (which consist of the crank handle, water connections, leader hose and will be free from defects in materials and workman-

ship under normal use for a period of ONE (1) YEARS from the date of original retail purchase. Notwithstanding the foregoing, the colors and

finishes of the Products may vary within a reasonable scope due to unavoidable color variations in different production batches, and such

variations shall not constitute a material defect. This limited warranty is limited solely to the original Customer with proof of purchase and is not

transferable.

1.2. THE WARRANTY:During a covered Product’s limited warranty period, Company will, at Company’s sole option and discretion, (1) repair

the defective component or product without charge or (2) replace the defective component or product without charge.

1.3. The foregoing limited warranty is subject to the Customer’s proper storage, transportation, handling and use of the Products as the same are

defined within Company’s then-current published guides and instructions for use and care. The limited warranty does not include defects due to

normal wear and tear, abuse or misuse, mishandling, neglect, accident, fire, lightning, sunlight or other natural hazard, delivery or transportation

damage, failure to follow applicable directions or instructions, or improper or inadequate cleaning, maintenance, care, repairs, modifications, or use

beyond a Product’s intended use. Please note that since the Structural Frame is made from plastic, fading may occur over time. As such, this

limited warranty does not include color fading or defects due to the same.

1.4. LIMITED WARRANTY CLAIMS PROCEDURE: To obtain performance under this limited warranty, Customer shall notify Company in

writing (to Liberty Garden Products, Inc., 1161 South Park Drive, Kernersville, NC 27284, Attn: Customer Service / Warranty Department), by email

(to [email protected]), or by telephone (to (336) 992-3595) with a full description of the defect that is covered by

warranty and a copy of the dated proof of purchase of the applicable product. Our warranty is limited to items purchased in new condition from

authorized distributors.

• Company shall review each such claim and issue Customer a return merchandise authorization (“RMA”) in the event that the described defect or

condition merits warranty review as determined by Company. Customers who have been issued a RMA shall, at Company’s election, return the

covered item to the same physical address listed above for reporting initial claims. Company shall not accept any returned product without a RMA.

• Upon receipt, Company will evaluate the returned product(s) to determine if there is a warranty claim and, if so, how Company wishes to remedy

the same. During a covered product’s respective limited warranty period, Company will, at Company’s sole and absolute option and discretion,

(1) repair the defective component or product without charge or (2) replace the defective component or product without charge. Refunds are not

available pursuant to this limited warranty.

• Customer is solely responsible for transportation of the covered product(s) to the Company for evaluation (if applicable and requested by

Company). In the event that Company determines that a claim under this limited warranty is justified, Company shall be responsible for

transportation of the repaired, corrected, replaced or exchanged product back to Customer. Customer shall be solely responsible for the

transportation of any product back to Customer if Company determines that a claim under this warranty is not justified.

• Any repaired, corrected, replaced or exchanged Products shall be subject to the Limited Warranty set forth to the duration of the original limited

warranty period as set forth in Section 1.1. and not for any extended duration, following their repair, correction, replacement or exchange.

1.5. IF A COMPANY PRODUCT DOES NOT CONFORM TO THESE LIMITED WARRANTIES, THE PURCHASER’S SOLE AND EXCLU-

SIVE REMEDY IS, AT COMPANY’S SOLE AND EXCLUSIVE OPTION, THE (1) REPAIR OF ANY DEFECTIVE PRODUCT OR COMPO-

NENT PART OR (2) REPLACEMENT OF ANY DEFECTIVE PRODUCT OR COMPONENT PART. THE LIMITED WARRANTY AND

REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND MADE IN LIEU OF ALL OTHER WARRANTIES, REMEDIES, RIGHTS OR

CONDITIONS, WHETHER ORAL OR WRITTEN, EXPRESS OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTO-

RY OR OTHERWISE, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE. COMPANY SPECIFICALLY DISCLAIMS, WITHOUT LIMITATION, ANY AND ALL OTHER WARRANTIES, EXPRESS OR

IMPLIED, OF ANY KIND. IF COMPANY CANNOT LAWFULLY DISCLAIM IMPLIED WARRANTIES UNDER THIS LIMITED WARRANTY,

ALL SUCH WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE, ARE LIMITED IN DURATION TO THE DURATION OF THIS LIMITED WARRANTY. The Company does not assume or

authorize any person to assume for them any other liability in connection with the Products.

LIBERTY GARDEN PRODUCTS LIMITED WARRANTY CONTINUED

2. EXCLUSION AND LIMITATION OF LIABILITY:

IN NO EVENT, WHETHER BASED ON CONTRACT OR TORT OR OTHER LEGAL THEORY, SHALL COMPANY BE

LIABLE FOR ANY INDIRECT, INCIDENTAL, PUNITIVE, SPECIAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT

NOT LIMITED TO, DAMAGES TO OTHER PROPERTY, INCONVENIENCE, DAMAGES FOR LOSS OF PROFITS,

REVENUE, GOODWILL OR USE, INCURRED BY CUSTOMER OR ANY THIRD PARTY, WHETHER IN AN ACTION IN

CONTRACT, TORT, STRICT LIABILITY, OR IMPOSED BY STATUTE, OR OTHERWISE, EVEN IF ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES. Some states do not allow the exclusion or limitation of incidental or consequential damages or

exclusions or limitations on the duration of implied warranties or conditions, so the above limitations or exclusions may not apply to Customer. In

jurisdictions that limit the scope of or preclude limitations or exclusion of remedies or damages, or of liability, such as liability for gross negligence

or willful misconduct or do not allow implied warranties to be excluded, the limitation or exclusion of warranties, remedies, damages or liability set

forth above are intended to apply to the maximum extent permitted by applicable law. This limited warranty gives the Customer specific legal rights,

and the Customer may also have other rights that vary by state, country or other jurisdiction.

3. SEVERABILITY:

If any provision of this limited warranty is held to be illegal, invalid or otherwise unenforceable, such provision will be enforced to the extent possible

consistent with its stated intention, or, if incapable of such enforcement, will be deemed to be severed and deleted from this limited warranty, while

the remainder of the terms of this limited warranty will continue in full force and effect.

4. DISPUTE RESOLUTION:

ThisLiberty Garden Products, Inc. Limited Warranty shall be governed by and construed in accordance with the laws of the State of North

Carolina, without regard to its principles of conflicts of law. The parties acknowledge the exclusive jurisdiction of the federal and state courts of the