LIEFGARDEN SL1688 User manual

Before returning the products, please fell free to contact our customer service
at whatsapp [phone] or write to [e-mail], we'll solve
as soon as possible. Monday - Friday 9:00 a.m. - 5:00 p.m.
Read all instructions before assembly.
Failure to do so may result in faulty assembly and potential injury.
Questions, problems, missing parts?
Solar Post Cap Light - Crack Ball
Model Number: SL1688
PACKAGE CONTENTS
Includes 1pc 1.2VAA 1000mAh rechargeable battery per light.
LED: The lifetime for LEDs is estimated to be 100,000 hours.
It should never need to be replaced.
A
C
D
Ref. Part Name
A
B
C
D
E
F
G
H
I
Solar Panel Unit
Glass Lens
Plastic Lens
Base
4-1/2” Adapter
4” Adapter
3-5/8” Adapter
Screws
Plastic Anchors
H
I
E
F
G
Sku No.: B0999HF687
Sku No.: B0998Y896G
Sku No.: B0998YBBKF
Sku No.: B0998YH1BL
Sku No.: B0998Y7114
Sku No.: B099927JL8
B

ASSEMBLY (Figure 1)
• Gently remove all parts from the package and
lay them out on a smooth surface. Note: Some
components may come preassembled.
• Note: Fits actual 5” x 5” post without the
use of any additional adapters. Additional
adapters included (Parts E, F & G) are nested
underneath the Base (Part D).
• Select the correct adapter size depending on
the size of the post. Includes 3 adapters:
• 4-1/2” x 4-1/2”
• 4” x 4”
• 3-5/8” x 3-5/8” (Fits Standard 4 x 4 Wood
Post)
• Place the body (part C&D, indivisible) onto the
post and mark with a pencil where you will need
to pre-drill for Screws (Part H) and Plastic
Anchors (Part I) if required.
• Remove the body (part C&D, indivisible) temporarily
and pre-drill holes if necessary.
• Replace the body (part C&D, indivisible) back
onto the post and secure with Screws (Part H) in 2 locations.
ASSEMBLY INSTRUCTIONS
IMPORTANT INFORMATION
FUNCTION: The built-in solar panels convert sunlight into electricity. The rechargeable battery stores the
energy and converts the power into light for use during the night. The lighting hours of the solar light
depends on the geographical location and weather condition. Stronger or longer exposure to sunlight
enables the battery to store more energy and provide longer lighting hours.
LOCATION: It is important to select an outdoor location with full, direct sunlight where the solar panel can
receive at least 8 hours of sunlight each day. Shady areas will not enable batteries to be fully charged. This
will reduce the lighting hours at night. It is also important to avoid placing the solar light by light sources,
such as street lights or porch lights, which may cause the solar light to turn off automatically. The solar light
is designated for outdoor usage and ideal for night lighting of garden, paths, etc.
CLEANING AND MAINTENANCE: Please use a damp cloth to clean the solar panel. Do not use any
chemical or abrasive cleaner. It is important to ensure that no moisture enters into the solar light.
Replacement parts may be ordered by using the fixture model number and part’s name; please write to the
e-mail address located at the top and bottom of this instruction manual.
RECHARGEABLE BATTERY: This product contains 1pc 1.2VAA 1000mAh rechargeable battery for
each. When the battery expires, it must be recycled or disposed of properly. Please contact your local
waste disposal authority for correct procedure. Do not put battery into fire.
Figure 1
E
F
G

OPERATION (Figure 2)
• Twist the Solar Panel Unit (Part A) a ¼ turn in a
counter clockwise direction until it separates from
the body (part C&D, indivisible) .
Slid the Switch underneath the Solar Panel Unit (Part A)
to select lighting according to your preference. RGB
and WHITE for your option, but never on OFF positon.
Take the light to direct sunshine that allows
the rechargeable battery to reach its maximum
capacity. Ensure the light is in full sunlight for 8
hours.
The unit will then automatically light up at dusk.
•
•
•
Note: Lights with crystalline panels may have a
protective film over the solar panel. This must be
removed prior to use.
OPERATIONAL INSTRUCTIONS AND BATTERY REPLACEMENT
CHANGING THE BATTERY (Figure 3)
• Twist the Solar Panel Unit (Part A) a ¼ turn in a
counter clockwise direction until it separates from
the body (part C&D, indivisible).
• Unscrew the screws at the four corners, and
separate the cover gently. (NOTE: wires inside are
connecting, so you have to be careful, otherwise, the
light will not work once wires are brocken).
• Replace the battery with a new 1.2VAA 1000mAh
solar rechargeable battery, ensuring the correct
polarity is observed.
• Reassemble the unit by reversing the above
procedure.
• Fully charge the battery before first use for up
to 2 days in full sunlight. The unit will then
automatically light up at dusk.
Figure 3
Figure 2

TROUBLESHOOTING
The light does not come on at night:
• Make sure the switch is on RGB or WHITE position, rather than on OFF position.
Check the rechargeable battery and make sure that it is in contact to the metal plate and the polarity is
correct. If the battery is worn out, replace the battery with a new AA 1000mAh rechargeable battery.
Always keep the solar light distant from other night light sources, such as exterior lights. Reposition the
light to avoid close contact with other night light sources.
Make sure solar panel is clean and free of dirt and debris. If needed use a damp cloth to clean the solar
panel. Do not use any chemical or abrasive cleaner. It is important to ensure that no moisture enters into
the solar light.
•
•
•
Questions, problems, missing parts?
Before returning the products, please fell free to contact our customer
service at whatsapp [phone] or write to [e-mail],
we'll reply as soon as possible.
Monday - Friday 9:00 a.m. - 5:00 p.m.