LifeSpan Kids Junior Jungle Flying Fox User manual

Junior Jungle
Flying Fox
USER MANUAL
WARNING: The disassembled product may contain small parts
which pose a choking hazard to children under 3.
IMPORTANT:
The owner’s manual contains safety, assembly, use and maintenance instructions. This product must
be assembled by an adult who has read and understood these instructions. Keep the packaging away
from children and dispose of all packaging before use.
NOTE:
This manual should not be used to guide your purchasing decision. Your product, and the contents
inside its carton, may vary from what is listed in this manual. This manual may also be subject to
updates or changes. Updated manuals are available through our website at
www.lifespankids.com.au.
For the installer and your children’s safety, it is important to fully read and understand the instructions
and safety hazards before commencing the assembly of the product.

TABLE OF
CONTENTS
I. GENERAL SAFETY INSTRUCTIONS
1.1 Danger for Children
1.2 Risk of Injuries
1.3 Risk of Injuries
1.4 Assembly Advice
II. SAFETY INSTRUCTIONS
III. ASSEMBLY INSTRUCTIONS
IV. MAINTENANCE
V. CLEANING
VI. WARRANTY
4
4
4
4
5
6
8
18
19
19

4
I. GENERAL SAFETY INSTRUCTIONS
NOTE: This product is intended for outdoor domestic use only.
1.1 DANGER FOR CHILDREN
WARNING: No eating while using the product at the same time.
•Children do not recognize potential dangers from this product. The unassembled
product must be stored out of reach of children and pets.
•This product may only be used with adult supervision at all times.
•The packaging material is not suitable for children due to choking and suffocation
hazards.
•Do not use the product if it is damaged or defective. If it is damaged or defective,
please contact a qualified technician.
•Check the product before each use. Defective parts must be changed immediately
as they can impair the function and the safety of the product.
•No more than one person to use the product at the same time.
•Use the product only on even and non-slipping surfaces. Never use it near water and
keep sufficient space around for safety.
•Beware of moving parts such as the springs or elastics, which could catch your arms
and legs. Do not place any objects or body parts in the product’s openings.
•Do not make alterations to the product. Only use original spare parts. Qualified
technicians should only carry out repairs – improper repairs can lead to danger
for the user. Use this product only as described in this manual.
1.2 RISK OF INJURIES
1.2 PRODUCT DAMAGE
GENERAL SAFETY INSTRUCTIONS

5
• The assembly of the product must be done carefully and by an able-bodied adult. If
in any doubt, ask a technically qualified person.
• Before you start with the assembly, read the instructions carefully.
• Remove all packaging materials and lay down all parts on an open space. This gives
you an overview and simplifies the assembly procedure.
• Check with the parts list that all parts are available. Dispose of the packaging
material when the assembly is completed.
• Beware that when using tools or doing technical work, there is always a risk of
injuries. Assemble the product with care.
• Create a danger free environment; for example, do not let tools lay around the
workspace. Store the packaging material in a way that cannot cause any danger.
• After installing the product according to the instruction manual, en sure all screws,
bolts and nuts are correctly installed and tightened and that all joints are secure.
• Reasonable space must be kept between the product and possible sources of
danger, such as other equipment swimming pools and fences.
• The assembly of the product must be done carefully and by an able-bodied adult. If
in any doubt, ask a technically qualified person.
• The product must be assembled correctly before use.
• Your play structure must be installed on a flat horizontal surface with a minimum
of 2m between it and any structure or obstacle such as a fence, garage house, tree
branches, cloths lines, or electric cables.
• Modifications made to the original product shall be carried out according to the instructions
of the manufacturer.
• The product must always be used in a well-lit area.
• Do not place anything under the product.
• Use gloves during assembly and disassembly.
• Outdoor products should be equipped with a device that in strong wind conditions avoid
displacement due to wind (e.g. steel bars in the ground or loads like sand bag or water bags).
• In certain areas during winter, snow buildup and the low temperatures can damage the
product. It is recommended to remove snow buildup and to store the product indoor.
• We strongly recommend visual inspections every 3 months to insure the integrity of the entire
product. Replace any parts as necessary.
1.4 ASSEMBLY ADVICE
GENERAL SAFETY INSTRUCTIONS

6
•The safety instructions of the product should always be considered and obeyed.
• Using the product may result in permanent injury such as paralysis, or even death. Falling off
the product may lead to injuries, particularly to the back, neck or head.
• No clothes with hooks or lose parts should be worn or carried during product usage in order to
avoid hooks getting caught and causing injury.
•Strong winds can result in the product being blown away or damaged. If strong winds are
predicted the product must be disassembled and moved to a sheltered area or sufficiently
anchored down.
•Moving the product whilst assembled may affect the integrity of the frame. Should it be necessary
to move the product, please consider the following:
1. Force to be evenly spaced around the frame to lift the product off the ground
2. The product must be carried horizontally
3. Use caution whilst moving as it could bend the product frame.
•Users should be familiar with the assembly manual. This manual contains assembly
guidance; selected precautionary measures as well as recommendations for servicing and
maintenance of the product, in order to ensure a secured and fun use of the product.
•Wear clothing free of drawstrings hooks loops or anything that could get caught in the basketball
set or safety enclosure.
• It is the responsibility of the owner or the supervisor to guarantee that all users of the product
are informed sufficiently of all warning references and safety instructions.
•The product can be only used if it is in good condition, worn or damaged parts should
be replaced.
•Objects, which could be dangerous to the user, should be away from the product.
•Avoid unauthorized and unsupervised use of the product.
•Do not use the product under influence of alcohol or drugs (incl. medicines).
•Do not use the product as a jumping platform for other articles.
The supervisor’s role is to make sure users are aware of all safety precautions and that these
precautions are enforced. When a supervisor is not available, the product may be disassembled or
covered to limit access.
For the supervisor
II. SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS

7
The US Consumer Product Safety Commission (CPSC) estimates that about 100 000 playground
equipment-related injuries resulting from falls to the ground surface are treated annually in US
hospital emergency rooms. Injuries involving this hazard pattern tend to be among the most serious
of all playground injuries, and have the potential to be fatal, particularly when the injury is to the
head. The surface under and around playground equipment can be a major factor in determining
the injury-causing potential of a fall. It is self-evident that a fall on to a shock-absorbing surface is
less likely to cause a serious injury than a fall onto a hard surface. Playground equipment should
never be placed on hard surfaces, such as concrete or asphalt, and while grass may appear to be
acceptable, it may quickly turn to hard-packed earth in areas of high traffic. Shredded bark mulch,
wood chips, tine sand or the gravel are considered to be acceptable shock absorbing surfaces
when installed and maintained at a sufficient depth under and around playground equipment.
However, it should be recognised that all injuries due to falls cannot be prevented, no matter what
surfacing material is used.
It is recommended that a shock absorbing material extend a minimum of 1 800 mm in all directions
from the perimeter of stationary equipment such as climbing frames and slides. However, because
children may deliberately jump from a moving swing, the shock absorbing material should extend
in the front and rear of a swing a minimum distance of twice the height of the pivot point measured
from a point directly beneath the pivot on the supporting structure.
This information is intended to assist in comparing the relative shock-absorbing properties of
various materials. No particular material is recommended over another. However, each material is
only effective when properly maintained. Materials should be checked periodically and replenished
to maintain correct depth as determined necessary for the equipment in question. The choice of
a material depends on the type and height of the playground equipment, the availability of the
material in a particular area, and its cost.
Table B.1 Lists the maximum height from which a child would not be expected to sustain a life-
threatening head injury in a fall on to four different loose-fill surfacing materials if they are Installed
and maintained at depths of 150 mm, 225 mm and 300 mm.
Table B.1 Fall height in millimetres from which a life-threatening head injury would not be expected.
Type of Material
Depth of surfacing material
150mm 225mm 300mm
Double Shredded Bark Mulch 1800 3000 3300
Wood Chips 1800 2100 3600
Fine Sand 1500 1500 2700
Fine Gravel 1800 2100 3000
Consumer Information Sheet for Playground Surfacing Materials
SAFETY INSTRUCTIONS

8
III. ASSEMBLY INSTRUCTIONS
COMBINATION A - PARTS LIST
FC 5001 X 1pc.
FC 5002 X 4pcs.
FC 4905 X 16pcs.
FC 5003 X 2pcs. FC 4903 X 4pcs.
FC 4911 X 4pcs.
FC 5004 X 1pc.
FC 4904 X 4pcs.
FC 4908 X 1pc. FC 4910 X 1pc.
M8X48MM
BR 01
32+1pcs.
18pcs.
8+1pcs. 2pcs.
14pcs.
M8X50MM M6X30MM
BR 02
M8X42MM
BR 03
9+1pcs.
9pcs.
M8X60MM
Anchor
32+1pcs.
5pcs.
ASSEMBLY INSTRUCTIONS
E
A B GC D

9
STEP 1
ASSEMBLY INSTRUCTIONS
ATTENTION:
1. DON’T fasten bolts until fully assembled.
2. DON’T over fasten bolts.
3. Before use, please check all bolts and
fasten properly.
POLE DIRECTION: FC5002
A
A

10
STEP 2
ASSEMBLY INSTRUCTIONS
ATTENTION:
Do not over fasten bolts before
complete assembly.
A
G

11
ASSEMBLY INSTRUCTIONS
STEP 3
ATTENTION:
1. DON’T fasten bolts until fully assembled.
2. DON’T over fasten bolts.
3. Before use, please check all bolts and
fasten properly.
A
A
A
A
B
B
B
B
CC
C
Dx32
FC 4903
(x4)
FC 4904
(x4)
FC 4905 (x16)
FC 4911(x4)
2
1

12 ASSEMBLY INSTRUCTIONS
STEP 4
A
A
E
C
x5

13
COMBINATION B - PARTS LIST
FC 5001 X 1pc.
FC 5002 X 3pcs.
FC 4905 X 8pcs.
FC 5003 X 2pcs. FC 4903 X 2pcs.
FC 4911 X 2pcs.
FC 5004 X 1pc.
FC 4904 X 2pcs.
FC 4908 X 1pc. FC 4910 X 1pc.
M8X48MM
BR 01
22+1pcs.
12pcs.
4pcs. 2pcs.
10pcs.
M8X50MM M6X30MM
BR 02
M8X42MM
BR 03
3pcs.
3pcs.
M8X60MM
Anchor
16+1pcs.
3pcs.
E
A B GC D
ASSEMBLY INSTRUCTIONS

14
STEP 1
POLE DIRECTION: FC5002
STEP 2
STEP 1
STEP 1. Disassemble 2 support bars & store it well for other use proposal.
STEP 2. Disassemble one of short leg on platform (FC4904), re-placed by a long leg (FC5002)
ATTENTION:
1. DON’T fasten bolts until fully
assembled.
2. DON’T over fasten bolts.
3. Before use, please check all
bolts and fasten properly.
ASSEMBLY INSTRUCTIONS

15
STEP 2
A
A
ASSEMBLY INSTRUCTIONS

16
STEP 3
ASSEMBLY INSTRUCTIONS
A
G

17
ASSEMBLY INSTRUCTIONS
STEP 4
ATTENTION:
1. DON’T fasten bolts until fully assembled.
2. DON’T over fasten bolts.
3. Before use, please check all bolts and fasten properly.
A
A
A
B
B
B
B
C
C
C
D
E
A
x3
2
1

18 MAINTENANCE
IV. MAINTENANCE
RECOMMENDATIONS:
WARNING: Please keep for future reference.
We recommend regular maintenance to be conducted at the beginning of each season as well as at
regular intervals during the usage session for your play equipment to ensure all main parts/fixings are
tightly secured, well-oiled and intact to avoid failure, injury or hazards.
GENERAL ADVICE
It is of particular importance that this is followed at the beginning of each season as well as at regular
intervals during the usage season.
•Check the accessories monthly as well as the play equipment’s structure to prevent falling risks.
•Check and retighten screws, bolts, and all other hardware elements as necessary.
a. Do not over tighten to avoid damaging the thread or cracking the surrounding wood.
•Check all coverings and bolts for sharp edges and replace when required.
•Lubricate all moving metallic parts.
• Equipment situated in a high moisture or high salt content locations are more likely to oxidant and
rust. Regular checks should be done more often. When signs of oxidation and / or rust appear on
various metallic parts of your equipment, sand rusted areas and tubular members and repaint
using a non-lead-based paint when required.
• Where applicable: check swing seats, chains, ropes, and other means of attachment for
evidence of deterioration.
•Replace when required in accordance with the owner’s manual.
• The play structure must be securely assembled.
• For safety reasons, the cement cubes must be poured 5cm below ground level, at the frame’s outer angles.
• The play structure must not be installed directly on cement, asphalt, or any other hard surface.
• Your play structure must be attached on a flat horizontal surface with a minimum of 2m between it and
any structure or obstacle such as a fence, garage house, tree branches, cloths lines, or electric cables.
If your play structure is disassembled, be sure to clearly mark any attached metal plates to prevent
accidents. Check all bolt covers and sharp edges and replace them if necessary.
For longer accessory life, we suggest storing them during the winter.

19
Do not use any abrasive cleansers for the cleaning. Use a soft, damp cloth to eliminate dirt and dust.
V. CLEANING
VI. WARRANTY
AUSTRALIAN CONSUMER LAW
Many of our products come with a guarantee or warranty from the manufacturer. In addition, they come
with guarantees that cannot be excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a major failure and compensation for any other
reasonably foreseeable loss or damage.
You are entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality
and the failure does not amount to a major failure. Full details of your consumer rights may be found at
www.consumerlaw.gov.au.
Please visit our website to view our full warranty terms and conditions:
www.lifespankids.com.au/Warranty-Policy-Kids
WARRANTY AND SUPPORT
Any claim against this warranty must be made through your original place of purchase. Proof of
purchase is required before a warranty claim may be processed.
If you have purchased this product from the Official Lifespan Kids website, please visit
www.lifespankids.com.au/warranty-form
For support outside of warranty, if you wish to purchase replacement parts or request a repair or service,
please visit www.lifespankids.com.au/warranty-form and fill in our Repair/Service Request Form or
Parts Purchase Form.
WARRANTY

www.lifespankids.com.au