Holzhof XT 100 Dirondello User manual

XT 100 "Dirondello"
assembly instructions

ASSEMBLY
TIME SEQUENCE
1. Fasten the "flag" panel to the pre-assembled structure using 4 M8x45 hex screws (at the
top), 9x M8x80 TORX screws (on sides) and 2x M4x50 TORX screws (near the platform).
2. Fasten the slide to the PE entrance using 4x M8x180 TORX screws.
3. Fasten the climbing board to the struts using 4x M8x80 TORX screws.
5. Fasten the brackets (anchoring or embedding, as requested).
Detailed instructions for each step can be found on the following pages.

fasten using a M8x45 hex screw
fasten using a M8x80 TORX screw
fasten using a M4x50 TORX screw
fastening detail on the following pages

PLEASE NOTE: It is advisable to only secure the
nuts and bolts permanently and insert the caps
once it has been checked that all the elements
have been positioned correctly.
Insert the nuts and bolts required for fastening
as shown in the figure in holes near the
widening on the "flag" panel (indicated on the
previous page with the letter A).
M8x45 hex screw
M8 washer finned PE cap
025 M8 self-locking nut
Article
Quantity
Name

M8x80 TORX screw
M8 washer finned PE cap
025
Article
Quantity
Name

Insert the nuts and bolts required for fastening as
shown in the figure in holes near the platform
(indicated on the previous page with the letter C).
M4x50 TORX screw
Article
Quantity
Name

Fasten the climbing board (4) to
struts 7 and 8 using appropriate
nuts and bolts as shown in the
figure.
M8x80 TORX screw
M8 washer finned
cap 025
Article Quantity Name

1. After securing the PE entrance (2), rest the body of the
curved slide (3) on the tower platform (1) and insert the
nuts and bolts necessary to secure it in the holes
present on the slide (3).
2. Once correct positioning, verticality and parallelism
have been checked, secure the nuts and bolts
completely and put the caps on.
3. Repeat the operation on the other side of the
slide.
NOTETHE COLOURS AND MODELS SHOWN ARE
FOR ILLUSTRATION PURPOSES ONLY
tower
PE entrance
curved slide
08 IS07089 washer
M8x180 TORX screw
PE cap

Fasten the embedding brackets to the
struts. The brackets should be fastened
inside the structure.
Details for each operation can be found on
the following pages.
For the plug solution, fasten
the angle bar instead of the
embedding brackets.

1. Mark the position of the holes on the
brackets (5) and create a pilot hole with a M6
tip on struts (6).
2. Fasten the brackets (5) to the struts (6)
using the nuts and bolts indicated in the
figure.
3. Repeat this operation on all brackets.
PLEASE NOTE : It is advisable to only secure
the nuts and bolts permanently and insert the
caps once it has been checked that all the
elements have been positioned correctly.
For the plug solution, fasten the
angle bar instead of the
embedding brackets with the
same procedure, inserting only
one screw however.
Fasten 2 angle bars to strut 4.
M8x80 TORX screw
M8 washer
PE nut cover
PE cap embedding
bracket strut

PLEASTE NOTE: The plinth must be created according to the specifications
indicated in the illustration shown below, as required by standard UNI EN 1176.
play surface
thickness 5 cm
1. Make a 50x50 cm hole that is 60 cm deep.
2. Position the upright with a bracket, shimming it 5 cm.
3. Cast concrete as per the diagram.
4. Once the concrete has hardened, fill the hole with loose shockproof
rubber up to the play surface level.
concrete casting-
/recover

1. Drill a hole.
2. Thoroughly clean the hole using
an air pump and brushes.
3. Insert the anchor in the hole
present on the angle bar.
4. Tighten using a torque
wrench.
PLEASE NOTE: It is advisable to only secure
the nuts and bolts permanently and insert
the caps once it has been checked that all
the elements have been positioned
correctly.
1. Drill a hole.
2. Thoroughly clean the hole using
an air pump and brushes.
3. Insert the anchor in the hole
present on the angle bar.
4. Tighten using a torque
wrench.
PLEASE NOTE: It is advisable to only
secure the nuts and bolts permanently
and insert the caps once it has been
checked that all the elements have
been positioned correctly.