Linak DESKLINE Kick & Click Fixed User manual

Page 1 of 34
LINAK.COM/DESKLINE
Kick & ClickTM
User manual

Page 2 of 34
Contents
Preface .......................................................................................................................................... 3
Important information ................................................................................................................. 4
Safety instructions........................................................................................................................ 4
Before installation, re-installation or troubleshooting.................................................................. 5
Before start-up .......................................................................................................................... 5
During operation ....................................................................................................................... 5
Misc. ......................................................................................................................................... 5
Only for EU markets ..................................................................................................................... 6
Only for Non EU markets ............................................................................................................. 6
Misuse .......................................................................................................................................... 6
Repairs .......................................................................................................................................... 7
Manufacturer’s declaration.......................................................................................................... 7
Declaration of conformity ........................................................................................................... 8
Misc. on the DESKLINE®system .................................................................................................. 9
Warranty ................................................................................................................................... 9
Maintenance ............................................................................................................................. 9
Description of the DESKLINE® Kick & ClickTM system ............................................................... 10
Kick & ClickTM Fixed.................................................................................................................... 11
Kick & ClickTM Adjustable............................................................................................................ 11
Kick & ClickTM Base .................................................................................................................... 12
Kick & ClickTM 3rd leg kit ............................................................................................................. 13
Assembly ....................................................................................................................................... 14
Kick & ClickTM Adjustable (standard) ........................................................................................... 14
Kick & ClickTM Adjustable (compact)............................................................................................ 15
Assembling the Kick & Click system .......................................................................................... 16
Assembling a three-legged desk ............................................................................................... 19
Mounting the tabletop ................................................................................................................ 20
Disassembly .................................................................................................................................. 22
Accessories ................................................................................................................................... 23
Disposal of LINAK’s products ..................................................................................................... 24
Drawing appendix ........................................................................................................................ 25
Addresses ...................................................................................................................................... 34

Page 3 of 34
Preface
Dear User,
We are delighted that you have chosen a product from LINAK®.
LINAK systems are high-tech products based on many years of experience in the manufacture and development
of actuators, electric control boxes, controls and chargers.
This User Manual does not address the end-user. It is intended as a source of information for the manufacturer
of the equipment or system only, and it will tell you how to install, use and maintain your LINAK electronics.
It is the responsibility of the manufacturer of the end-user product to provide a User Manual where relevant
safety information from this manual is passed on to the end-user.
We are sure that your LINAK product/system will give you many years of problem-free operation.
Before our products leave the factory, they undergo full function and quality testing. Should you nevertheless
experience problems with your LINAK product/system, you are always welcome to contact your local contact.
LINAK subsidiaries and some distributors situated all over the world have authorised service centres, which are
always ready to help you.
LINAK provides a limited warranty on its products. This warranty is, however, subject to correct use in
accordance with the specifications, maintenance being done correctly, and any repairs being carried out at a
service centre, which is authorised to repair LINAK products. Changes in installation and use of LINAK products/
systems can affect their operation and durability. The products are not to be opened by unauthorised personnel.
You can review the full terms of the LINAK warranty on the LINAK website www.linak.com/warranty.
The User Manual has been written based on our present technical knowledge. We are constantly working on
updating the information and we therefore reserve the right to carry out technical modifications.
LINAK A/S

Page 4 of 34
Safety instruction
General
Important information
Important information on LINAK®products can be found under the following
headings:
Warning!
Failure to comply with these instructions may result in accidents involving
serious personal injury.
Failing to follow these instructions can result in the product being damaged
or being destroyed.
Safe use of the system is possible only when the operating instructions are read
completely and the instructions contained are strictly observed.
Failure to comply with instructions marked with the ”NOTE” symbol may result in
serious damage to the system or one of its components.
It is important for everyone who is to connect, install, or use the systems to
have the necessary information and access to this User Manual. Follow the
instructions for mounting – there is a risk of injury if these instructions are not
followed.
The appliance is not intended for use by young children or infirm persons
without supervision.
If there is visible damage to the product, do not install it.
Please note that during construction of applications in which the actuator
is to be fitted, there must be no possibility of personal injury, for example
squeezing of fingers or arms.
Assure free space for movement of the application in both directions to avoid
blockades.

Page 5 of 34
Before installation, re-installation, or troubleshooting:
• Stop the columns.
• Switch off the power supply and pull out the mains plug.
• Relieve the columns of any loads, which may be released during the work.
Before start-up:
• Make sure that the system has been installed as instructed in this User Manual.
Describing the motor system.
• Make sure that the voltage of the control box is correct before connecting the
system to the mains.
• System connection. The individual parts must be connected before connecting the
control box to the mains. See the User Manual for LINAK actuators, if necessary.
During operation
• If the control box makes unusual noise or smells, switch off the mains voltage
immediately.
• Duty Cycle: 10%, Max. 2 min./18 min. pause
• Take care that the cables are not damaged.
• Unplug the mains cable on mobile equipment before moving it.
• The products must only be used in an environment, that corresponds to their IP
protection.
Misc.
For further information, installation guidelines etc. for the motor system, please see
the relevant user manual: www.linak.com/deskline.
Updated manuals and declarations can always be found here:
www.linak.com/deskline.

Page 6 of 34
Only for EU markets
This appliance can be used by children aged from aged 8 years and above
and persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved.
Children shall not play with the appliance. Cleaning and user maintenance
shall not be made by children without supervision.
Only for Non EU markets
Persons who do not have the necessary experience or knowledge of the
product/products must not use the product/products. Besides, persons with
reduced physical, sensory or mental abilities must not use the product/
products, unless they are under surveillance or they have been thoroughly
instructed in the use of the apparatus by a person who is responsible for the
safety of these persons.
Moreover, children must be under surveillance to ensure that they do not
play with the product.
It is the operator’s responsibility to ensure that there is free space for the
application to move without risk for the operator or bystanders before
operating the application.
Misuse
Do not overload the actuators – this can cause danger of personal injury and
damage to the system.
Do not use the actuator system for lifting persons. Do not sit or stand on a
table while operating – risk of personal injury.
Do not use the system in environments other than the intended indoor use

Page 7 of 34
Repairs
In order to avoid the risk of malfunction, all DESKLINE®repairs must only be carried out by authorised LINAK service centres or
repairers, as special tools must be used and special gaskets must be fitted. Products under warranty must also be returned to
authorised LINAK service centres.
Further information on DESKLINE warranty can be found on the LINAK website www.linak.com/warranty.
Warning!
If any of the DESKLINE®products are opened, there will be a risk of subsequent malfunction.
Warning!
The DESKLINE®systems do not withstand cutting oil.
DECLARATION OF INCORPORATION OF PARTLY COMPLETED MACHINERY
LINAK A/S
Smedevænget 8
DK -6430 Nordborg
Herewith declares that LINAK DESKLINE®products as characterized by the following models and types:
Control Boxes CBD6S
Linear ActuatorsDB5, DB6, DB7, DB9, DB12, DB14, DB16, LA23, LA31
Lifting ColumnsDL1A, DL2, DL4S, DL5, DL6, DL7, DL8, DL9, DL10, DL11, DL12, DL14, DL15,
DL16,DL17, DL19, BASE1
Desk PanelsDPA, DPB, DPH, DPF, DPG1K, DPG1M, DPG1B, DPG1C, DPT, DP1, DP1CS,
DP1K, DP1V, DP1U
RF ControlsHB10RF,HB20RF, RFT, RFRL
Accessories BA001, SLS, Kick & Click
comply with the following parts of the Machinery Directive 2006/42/EC,ANNEX I,Essential health and
safety requirements relating to the design and construction of machinery:
1.5.1 Electricity supply
The relevant technical documentation is compiled in accordance with part B of Annex VII and that this
documentation or part hereof will be transmitted by post or electronically to a reasoned request by the
national authorities.
This partly completed machinery must not be put into service until the final machinery into
which it is to be incorporated has been declared in conformity with the provisions of the
Machinery Directive 2006/42/EC where appropriate.
Nordborg, 2017-12-08
LINAK A/S
John Kling, B.Sc.E.E.
Certification and Regulatory Affairs
Authorized to compile the relevant technical documentation
Original Declaration

Page 8 of 34
DECLARATION OF CONFORMITY
LINAK A/S
Smedevænget 8
DK - 6430 Nordborg
hereby declares that LINAK Actuator System composed of:
Control Box(s) CBD6SP00020A-309
CBD6S*000*0A-709
(The ‘*’ in the product description can either be a character or a number, thereby defining the variation of the product)
And
Linear Actuator(s) 31, DB4, DB5, DB6, DB7, DB9, DB12, DB14, DB16, LA23 series and / or
Lifting Column(s) DL1A, DL2, DL4, DL5, DL6, DL7, DL8, DL9, DL10, DL11, DL12, DL14, DL15, DL16, DL17, DL19,
BASE1 series
And
Desk Panel(s) DP1C, DP1K, DP1L, DP1V, DP1U, DPA, DPB, DPF, DPG, DPH, DPT, WDPL1 series
complies with EMC Directive: 2014/30/EU according to following standards:
EN 61000-6-1:2007, EN 61000-6-3:2007+A1:2011+AC:2012
complies with Low Voltage Directive 2014/35/EU according to the standard:
EN 60335-1:2012+A11:2014
complies with RoHS2 Directive 2011/65/EU according to the standard:
EN 55581:2012
Additional information:
The system does also comply with the standard: EN 13849-1:2015 SRP/CS Cat. B, PL = b and SRESW PL = b
Note 1: Exempted CBD6S with SW03003007 printed on the label.
Nordborg, 2017-12-08
LINAK A/S
John Kling, B.Sc.E.E.
Certification and Regulatory Affairs
Authorized to compile the relevant technical documentation
Original Declaration

Page 9 of 34
Misc. on the DESKLINE®system
This system is a DESKLINE system developed for desks and for indoor use in offices. Do not use it in industrial kitchens or in
other environments that have to be cleaned with aggressive detergents.
Warranty
This DESKLINE product is subject to warranty pursuant to the terms of LINAK DESKLINE Warranty Paper, available on the LINAK
website www.linak.com/warranty.
Maintenance
Clean dust and dirt off the outside of the system at appropriate intervals and inspect them for damage and breaks.
Inspect the connections, cables, and plugs and check for correct functioning as well as fixing points.

Page 10 of 34
1: Clamp
2: Kick lock
3: Cantilever
4: Inner rail
5: Outer rail
6: Clips
Description of the DESKLINE®Kick & ClickTM system
The Kick & ClickTM system is the smart and intuitive solution for mounting DESKLIFT™ columns to the tabletop. The solution is
perfect for various office desks. The unique feature of Kick & Click is the way of mounting. Click the system together without
using tools and screws, simply clever. Kick & Click is a modular concept compatible with all DESKLINE®columns with motor
housing leaving the design to the desk manufacturer. Kick & Click comes standard in 3 variants:: Kick & Click Adjustable
(standard or compact), Kick & Click Fixed and Kick & Click Base. Additionally, Kick & Click can be used for creating large three-
legged office desks by joining a Kick & Click 3rd leg kit with a Kick & Click system.
Kick & ClickTM: names of the different parts
Features for all versions:
• Max. total load (including the tabletop):
- Two-legged desks: 160 kg equally loaded, i.e. 80 kg on each column
- Three-legged desks: 240 kg equally loaded, i.e. 80 kg on each column
• Colour (all metal parts): Available in black (RAL 9005), grey (RAL 9006), or white (RAL 9016)
• Cantilever length: 550 mm
• Oval holes ensure flexibility as regards pre-drilling holes in tabletop
• Central or off-centre placement of columns (T-desk or C-desk)
Kick & ClickTM Fixed:
• Fits desks of 1200 mm (frame width 1140 mm)
• Set-packed or bulk deliveries
• Can be delivered with screws for mounting the tabletop
Kick & ClickTM Adjustable:
• Fits desks
- Standard: from 1400 to 2000 mm (frame width 1340 to 1940 mm)
- Compact: from 1000 to 1300 mm (frame width 940 to 1240 mm)
• Set-packed (both versions) or bulk deliveries (standard version only)
• Can be delivered with screws for mounting the tabletop
Kick & ClickTM Base:
• Base consists of Cantilever (x2), Base (x2), Clamp (x2) and Kick Lock (x2) for a two-legged desk
• Bulk deliveries only

Page 11 of 34
Kick & ClickTM Fixed
Compared to the Adjustable system the Fixed system only consists of one rail which is welded onto the base in both ends.
Kick & ClickTM Adjustable
The Adjustable system includes a telescopic inner and outer rail onto which the base is welded.

Page 12 of 34
Kick & ClickTM Base
The Base system is without the inner and the outer rail. The system is preferred if the OEM want to weld his own rail onto the
Base, or if the desk design does not need a rail e.g. due to tabletop thickness. The Base system could also be used for a 3 leg
desk.
The allowed welding area (shaded) on the base is shown here:
The Kick & Click base must only be used in connection with a Kick & Click cantilever.
Do not develop your own cantilever!

Page 13 of 34
The 3rd leg kit system includes a telescopic inner and outer rail with a base welded onto the outer rail.
Kick & ClickTM 3rd leg kit

Page 14 of 34
Assembly
A mounting instruction video is available here.
Table size and type
The Kick & Click is designed for T-desks and C-desks. The cantilevers must be mounted centrally on the tabletop.
Kick & Click adjustable (standard)
Kick & Click Adjustable (standard) and control box mounted on the tabletop (cantilevers centrally placed)
Recommended tabletop
Material Veneered chipboard
Plywood
Thickness Min 21 mm (13/16”)
Size Min. 700 x 1200 mm (27” x 47”)
Max. 1000 x 1830 mm (39” x 72“)

Page 15 of 34
Kick & Click adjustable (compact)
Kick & Click Adjustable (compact) and control box mounted on the tabletop (cantilevers centrally placed)
Recommended tabletop
Material Veneered chipboard
Plywood
Thickness Min 21 mm (13/16”)
Size Min. 700 x 1000 mm (27” x 39.5”)
Max. 1000 x 1300 mm (39” x 51“)

Page 16 of 34
Assembling the Kick & Click system
Kick & Click Adjustable
1. Gather all parts for the desk.
2. Fix the inner rail with the outer rail (only Kick & Click Adjustable).
2.1. Extend the rails to the required length
(frame width from 1140 to 1940 mm)
using the holes on the rails as a length indicator.
2.2. Fix the length with the clip.
3. Slide the cantilevers onto the base of the inner and outer rails.

Page 17 of 34
4. Align the cantilever
5. Mount the column by placing it in the base.
The Column is prepared for Kick & Click™ with slots on the backside of the housing (see drawings)
Align the middle marker on the cantilever
with the centre on the inner rail/outer rail
Outer markers on the cantilever indicate 50 mm maximum
displacement from the centre on the inner rail/outer rail
T-desk C-desk

Page 18 of 34
6. Place the clamp on the column housing, press it down gently. It will still be possible to move clamp a little when placed.
7. Place the Kick Lock in the clamp. The arrow on the Kick Lock must face the arrow on the clamp.
8. Fix the Kick Lock in the clamp with your foot. When you hear a “click”, the Kick Lock is mounted and the column is fixed
to the Kick & Click parts.
Repeat the mounting in the other end.

Page 19 of 34
Mount the Kick & Click Adjustable system as described above.
1. Gather all 3rd leg kit system parts.
2. Fix the inner rail with the outer rail.
Assembling a three-legged desk
The 3rd leg kit has only one base which is welded onto the outer rail.
2.1. Extend the rails to the required length (frame width
from 1100 to 1700 mm) using the holes on the rails
as a length indicator.
2.2. Fix the length using the clip.
3. Finish mounting the Kick & Click 3rd leg kit following the same procedure as in Assembling Kick & Click system, steps 3 to 8.
Example of Kick & Click three-legged desk

Page 20 of 34
Mounting the tabletop
Old Kick & Click versions with circular holes
Do not pre-drill holes for all the parts.
The combination of hole tolerances on each part, e.g. cantilever and rail, will cause uncertainty about the overall
tolerances on the assembled Kick Click system.Therefore, we recommend drilling the holes when the assembled frame
is mounted to the tabletop.
Exceptions:
- Fixing the Kick & Click Adjustable to a tabletop
With a Kick & Click Adjustable system, a customer can pre-drill the holes for the cantilevers to fix the system to
the tabletop. This can be done because the rails are adjustable. The hole size is 5.3 ± 0,2 mm and the tolerances
on the distance between the holes are ± 0.2 mm.
- Fixing the Kick & Click Fixed to a tabletop
With a Kick & Click Fixed system, a customer can pre-drill the holes for the rail to fix the system to the tabletop.
The hole size is 5.3 ± 0.2 mm and the tolerances on the distance between the holes are ± 0.5 mm.
Max. distance from the centre of the base to edge of the tabletop: 550 mm
Max. distance from the centre of the base to centre of the cantilever: 50 mm
The oval holes in the inner and outer rails and in the cantilevers of the Kick & Click system facilitate mounting of tabletops with
pre-drilled holes.
Figure 9 Kick & Click tabletop alignment measurements in mm