Liquifi ELEMENTS Series User manual
OUTDOORTV USER MANUAL
Sizes:
42’’,47’’,55’’,65’’
Rev 1.2
Warnings..............................................................................3-5
Supplied Accessories...........................................................6
Waterproof Remote Control Detail………………………………...8-10
First Fix Kit –Cabling............................................................11
Installation and Positioning...............................................................11
Connection details…………………………………………………………..12
Control Buttons……………………………………………………………….12
Setup and Tuning………………………………………………………..…..13-21
RS232 and Infra-Red Codes………………………………………………22
FEATURES…………………………………………………………………………23
Troubleshooting……………………………………………………………….24
Contents
-2 - www.liquifi.com.au
Before operating the set, please read this manual carefully.
Warning
WARNING :
To reduce the risk of electric shock do not remove cover (or back). No user serviceable parts inside. Refer
servicing to qualified service personnel. To prevent fire or shock hazard , do not expose the rear of the set to
rain or moisture.
CAUTION:
Unauthorized tampering with the inside of the TV invalidates the warranty.
The manufacturer shall not warrant for any damage caused by improper maintenance and/or repair
work by third parties.
Important safeguards for you and your new product:
Your product has been manufactured and tested with your safety in mind. However, improper use can
result in potential electrical shock or fire hazards. To avoid defeating the safeguards that havebeen built
into your new product, please read and observe the following safety points when installing and using your
new product and save them for future reference. Observing the simple precautions discussed in this
operating guide can help you get many years of enjoyment and safe operation from your new TV.
This product complies with all applicable regulations and voluntary safety standards.
1. Read Instructions
All safety and operating instructions should be read before the product is operated.
2. Follow Instructions
All operating and use instructions should be followed.
3. Retain Instructions
The safety and operating instructions should be retained for future reference.
4. Heed Warnings
All warnings on the product and in the operating instructions should be adhered to .
5. Cleaning
Disconnect the unit from the electricity supply before cleaning. Do not use abrasive cleaners. Use a damp
cloth for cleaning.
-3 - www.liquifi.com.au
6. Transporting Product
A product and cart combination should be moved with care. Quick stops, excessive force and uneven surfaces
may cause the product and cart combination to overturn.
7. Ventilation
Your TV will not, under normal operating conditions, require any ventilation. It has been
designed so that any heat will dissipate through the glass at the front of the unit. This will get hot, but need
not cause concern. If the unit is to be installed in a place other than the bathroom or other domestic room,
please consult your supplying dealer. Forced air ventilation will be required if this product is to be used in a
steam room, sauna, or similar.
8. Power Sources
This product should be operated only from the type of power source indicated on the marking label. If you
arenot sure of the type of power supply to your home, consult your supplying dealer.
9. Power Lead Polarization
This product is equipped with a three-wire grounding-type cord. This is a safety feature. Do not defeat the
safety purpose of the grounding-type cord.
10. Power Cord Protection
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords at plugs, convenience receptacles and the point
wherethey exit from the product.
11. Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the product, be sure the antennaor cable system is
grounded so as to provide some protection against voltage surges and built-up static charges . A “face plate
alsoneeds to be installed with an isolating capacitor to prevent any damage from static.
12. Lightning
For added protection for this product during a lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will
prevent possible damage to the product due to lightning and power-line surges.
13. Power Lines
An outside antenna system should not be located in the vicinity of overhead power lines or other electric light
or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna
system, extreme care should be taken to avoid contact with such power lines or circuits, as contact with them
might be fatal.
14. Earthingthe product
This product must be earthed properly to comply with the safety regulations in the country of use. If you are
unsure of these regulations, please consult a qualified electrician
15. Servicing
Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous
voltages or other hazards. Refer all servicing to qualified service personnel. If the TV does not operate
properly,switchit off and call your dealer.
16. Mounting
The product should be mounted on a wall only as recommended in the instructions.
Warning(cont)
-4-
17. Caution: Modifications
Do not attempt to modify this product in any way without written authorisationfrom TV.
18. Damage Requiring Service
Isolate this product from the mains supply and refer servicing to qualified service personnel under the following
conditions:
a. If the power-supply cord or plug is damaged.
b. If the glass front has been damaged.
c. If there is ingress of water between the glass and the LCD screen.
d. If the product does not operate normally by following the operating instructions. Adjust only those controls
that are covered by the operating instructions as an improper adjustment of other controls may result in damage
and will often require extensive work by a qualified technician to restore the product to its normal operation.
e. If the product has been dropped or the cabinet has been damaged.
f. If the product exhibits a distinct changein performance.
19. Replacement Parts
When replacement parts are required, be sure the service technician has used replacement parts specified by
Liquifi or have the same characteristics as the original part. Unauthorized substitutions may result in fire,
electric shock, or other safety hazards.
20. Please note:
The installation of your TV unit should be carried out by a technically competent and qualified person
and must conform to all the relevant regulations. If in doubt, please refer to your supplying dealer.
21. Power
This set operates on an AC supply; the voltage is as indicated on the label on the back cover. This appliance must
be earthed at all times through the chassis as well as through the power lead.
22. Location
This TV must be positioned according to the latest regulations concerning the area it will be installed
into. Position your TV so that no bright light or sunlight will shine directly on the screen and locate it at a suitable
viewing height. Do not expose the TV to vibration, dust or heat. Also ensure that the TV is placed in a position
that allows a free flow of air.
23. Installation
It is the installer’s responsibility to ensure that the TV unit is installed and sealed correctly as stated in
these instructions and in conjunction with the latest safety regulations.
-5 - www.liquifi.com.au
Warning(cont)
Waste Electricaland Electronic Equipment (WEEE)Directive
In the European Union, this symbol indicates that this product should not be disposed of with
household waste. It should be deposited at an appropriate facility to enable recovery and recycling.
This product contains Electrical/Electronic Parts which are produced using components in
compliance with the requirements of: European Union Directive 2002/195/EC for the Restriction
of the use of certain Hazardous Substances in Electrical and Electronics Equipment (RoHS).
Waterproof Remote Control Detail
www.liquifi.com.au -8-
POWEROn/Off button –Turns TV on
from, or off to, standby
SOURCEbutton –Displays the Input Source menu
and allows source selection: DTV, ATV, HDMI, etc.
TIMERbutton –Displays/sets the sleep timer
MUTEbutton –Turns the sound on or off
DISPLAY button –Switches between picture
formats: Auto, 16:9, 4:3, Zoom1, Zoom2
SCAN button –
TV/RADIObutton –Switches between DTV and
Radio
Picture Mode button –Switches between picture
modes: Standard, Movie, Dynamic, Personal, Soft
MENU button –Displays or closes the menus
EXIT button –Closes all on-screen menus and lists
TTX button –If main input source is TV that
includes TTX information, enters TTX display mode
FAV button –Displays or closes the favourite
programmelist.
Up button –Menu and EPG navigation
Down button –Menu and EPG navigation
Waterproof Remote Control Detail(cont)
-9 - www.liquifi.com.au
Left button –Menu and EPG navigation
Right button –Menu and EPG navigation
OK button –Accepts menu selections or displays
the programmelist
EPGbutton –Displays the Electronic Programme
Guide
SUBTITLEbutton –Switches subtitles on or off
LR/MTS button –No function
COLOUR button –DTV
Text and text menu
options
NUMBER buttons –Input
programmenumbers
Backbutton –switches between last and current
programmes
USB PLAY button –Accepts menu selections or
displays the USB programmelist
VOL (Volume up/down) buttons –Adjust
the volume
CH (Programmeup/down) buttons –Selects
next or previous programme
Waterproof Remote Control Detail(cont)
Before the waterproof remote control can be used the insulating plastic film must be removed from
beneath the battery.
Place the remote control face down on a horizontal flat surface and use the opener to release the
battery compartment cover by rotating it in an anti-clockwise direction. Set the battery cover and
opener to one side.
Rest one finger lightly on the battery and pull the printed tag to ease the insulating film from
underneath the battery. Try to avoid touching the black O-ring as it is coated in light grease.
Replace the battery cover and lock it back in place using the opener.
www.ůŝƋƵŝĨŝĐŽŵĂƵ -10 -
First Fix Kit –Cabling
Power Requirement (Mains)
Liquifi requires a 10 amp socket outlet connected to a 240 V mains supply via a readily
accessible isolation switch. This electrical installation must include an all-pole switch with a contact
separation of at least 3 mm in each pole. Both the socket and the isolation switch must conform to
the latest safety specification and be protected via an RCCD device or similar. This socket must be
fitted in a dry area, away from any moisture (usually in the ceiling). The mains plug must be fitted
with a 5 amp fuse..
-11 - www.liquifi.com.au
Pleasenote All electrical installation should be carried out byafullyqualified
electrician and all fire &safetyregulations must be obeyed.
Installation and Positioning
Further details can be found on the back of each screen.
Universal VESA Wall Mount:
The wall must be strong enough to hold at least 100kg.
VESA Mount (optional)
Connection details
Further details can be found on the back of each screen.
www.liquifi.com.au -12 -
Note:
Aviation plug Connector Array
AC100-270V Power In
HDMI (High Definition Multimedia Interface)
PC/Analog RGB Input (D-SUB)
S-VIDEO In (Optional)
AV In(Option Video = yellow Audio White = Left,
Red = Right)
PC Audio In
RF In(Antenna Input 75 Ω)
USB disk In (Optional)
RS-232
Control buttons (bottom corner of back cover)
Setup and Tuning
-13 - www.liquifi.com.au
Initial Tuning
Press the POWER ( ) button on the remote control to switch the TV on from standby.
The LED indicator will show yellow and After a few seconds the OSD language menu will be displayed.
(To switch the TV to standby, press the POWER ( ) button again. The LED indicator will show red to
indicate that the TV is in standby mode)
The on-screen menus can be in any of the following nine languages:
English, Español, Françes, Italiano, Nederlands, Polski, Portugês, Pyccкий, and Deutsch.
1. Press the UP ( ) button/DOWN ( ) button or LEFT ( ) button/RIGHT ( ) button to select OSD
Language, and then OK ( ) button.
2. Nonce to select Auto Tuning and display the Country selection window
3. Select the required country with the buttons. Choose from:
Australia, Austria, Belgium, Bulgaria, Croatia, Czech, Denmark, Finland, France, Germany, Greece, Hungary, Italy,
Luxembourg, Netherlands, Norway, Poland, Portugal, Romania, Russia, Serbia, Slovenia, Spain, Sweden, Switzerland,
UK.
4. Press the OK ( ) button to start the auto tuning.
The Channel Tuning dialogue will be displayed to show the progress of the tuning.When tuning is complete the
Channel Tuning dialogue will be cleared and the first available channel will be selected.
1. Press the Source ( ) button to display the Input Source list.
2. Press the UP ( ) button / or the DOWN ( ) button until the required source is selected.
3. Press the OK ( ) button to confirm selection of the chosen input and to clear the Input Source list from the
screen.
Press the EXIT ( ) button to close the Input Source list without selecting an alternative source.
The Input Source list allows selection of the following: DTV (Digital Television), ATV (Analogue Television), PC-RGB,
HDMI, AV (Video / Audio L / Audio R), and USB disk.
www.liquifi.com.au -14 -
Selecting aSource
-15 - www.liquifi.com.au
Screen Menu
Press Menu ( ) button to show Channel, Picture, Sound, Time, Option, Lock menu.
Press OK ( )button to select specific submenu and the adjustable value. In the submenu, Press the UP ( )
button/DOWN ( ) button to select menuitem.
1. ChannelMenu
-Auto Turing-
Press the UP ( ) button/DOWN ( ) button to select Auto Tuning, and then press OK ( )button and input
the password NO.“0000 then to choose ATV/DTV/ATV+DTV with LEFT ( ) button / RIGHT ( ) button and
press UP ( ) button/DOWN ( ) button or LEFT ( ) button / RIGHT ( ) button to select country channel
like German, Italy.
-DTVManual Tuning -
Press UP ( ) button/DOWN ( ) buttonto select DTV Manual Tuning, and then press OK ( )button and
input the password NO.“0000 then press LEFT ( ) button / RIGHT ( )button to select channel number, or
directly press number keys to select channel number, and then press OK ( ) button to begin to search channel.
-ATVManual Tuning -
Press UP ( ) button/DOWN ( )button to select ATV Manual Tuning, and then press OK ( ) and input the
password NO.“0000 then press LEFT ( ) button / RIGHT ( )button to select. Press UP ( ) button/DOWN
( ) buttonor LEFT ( ) button / RIGHT ( )button to select specific submenu and the adjustable value.
-Program Edit -
Press UP ( ) button/DOWN ( )button to select program edit, and then press OK ( )button to enter menu.
-Signal Information-
Press UP ( ) button/DOWN ( )button to select Signal Information, and then press OK ( )button to see
Signal Information
-LCN Sorting-
Press UP ( ) button/DOWN ( )button to select LCN Sorting, and then press OK ( )button to set sort
on/off
-SoftwareUpdate (USB)-
Press UP ( ) button/DOWN ( )button to select Software Update, connect USB Port to operate.
www.liquifi.com.au -16 -
2. Picture Menu
-Picture Mode Standard -
Press UP ( ) button/DOWN ( ) buttonto select Picture mode, and then OK ( )button to enter. Press LEFT
( ) button / RIGHT ( ) button to select standard/mild/dynamic mode and press UP ( ) button/DOWN
( ) button or LEFT ( ) button / RIGHT ( ) buttonto adjust value.
-Color Temperature-
Press UP ( ) button/DOWN ( ) buttonto select Color Temperature, and then OK ( )button to enter and
press LEFT ( ) button / RIGHT ( ) button to select cool/ warm/ user mode.
-Aspect Ratio -
Press UP ( ) button/DOWN ( ) buttonto select Aspect Ratio, and then OK ( )button to enter
-Noise Reduction-
Press UP ( ) button/DOWN ( ) buttonto select Noise Reduction mode, and then OK ( )to enter submenu.
You can select off/low/middle/high/default by pressing UP ( ) button/DOWN ( )button.
-Screen-
Press UP ( ) button/DOWN ( ) button to select Screen mode, and then press OK ( )to enter submenu in
pc mode.
3. Sound Menu
-Sound Mode Sound Bar -
Press UP ( ) button/DOWN ( ) button to select Sound Mode, and then OK ( )button, press LEFT ( )
button / RIGHT ( )button to select standard/music/movie/sports/user/intspk/sound bar mode.
-Balance -
Press UP ( ) button/DOWN ( ) button to select Balance, and OK ( )button to enter submenu, press LEFT
( ) button / RIGHT ( )button to adjust balance value.
-SurroundSound -
Press UP ( ) button/DOWN ( ) button to select Surround Sound, and then OK ( )button to enter submenu,
then press UP ( ) button/DOWN ( ) button to select off/surround/SRS trusurroundXT mode.
-AD Switch -
Press UP ( ) button/DOWN ( ) button to selectAD Switch, and then OK ( )button to select on/ off, and
you can adjust AD volume value by pressing LEFT ( ) button / RIGHT ( )button when AD switch is set to on.
-17 - www.liquifi.com.au
-Clock -
Press UP ( ) button/DOWN ( ) button to select Clock, and then OK ( )button to set.
-Off Time -
Press UP ( ) button/DOWN ( ) to select Off Time, and then OK ( )button to enter the submenu, press
LEFT ( ) button/RIGHT ( )to select off/once/everyday/Mon-Sat etc. And you can adjust hour or minute by
pressing LEFT ( ) button/RIGHT ( )button.
-On Time -
Press UP ( ) button/DOWN ( ) button to select On Time, and then OK ( )button to enter the submenu,
press LEFT ( ) button/RIGHT ( )to select off/once/everyday/Mon-Sat etc. And you can adjust hour / minute /
source /channel / volume by pressing LEFT ( ) button/RIGHT ( )button.
-Sleep Timer-
Press UP ( ) button/DOWN ( )to select Sleep Timer, and then OK ( )button to enter submenu, and press
UP ( ) button/DOWN ( )to select the sleep timer type .
-Auto Standbyoff -
Press UP ( ) button/DOWN ( )to select Auto Standby offand then OK ( )button to set and select 3h/4h
etc.
-Time Zone -
Press UP ( ) button/DOWN ( ) to select Time Zone, and then OK ( )button to enter submenu, and press
UP ( ) button/DOWN ( )or LEFT ( ) button/RIGHT ( ) buttonto adjust the time zone.
4. Time Menu
5. Option Menu
-OSD Language -
Press UP ( ) button/DOWN ( ) button to select OSD Language, and then OK ( )button. Press
UP( )button/ DOWN ( ) button or LEFT ( ) button/RIGHT ( ) button to choose language choices.
-Audio Language -
Press UP ( ) button/DOWN ( ) button to select Audio Language, and then OK ( )button to enter submenu,
and then press LEFT ( ) button/RIGHT ( )button to select primary or secondary type.
-Subtitle Language -
Press UP ( ) button/DOWN ( ) button to select Subtitle Language, and then OK ( )button to select prime
or second.
-Hearingimpaired-
Press UP ( ) button/DOWN ( ) button to select Hearing impaired, and then OK ( )button to select on/off
-Country-
Press UP ( ) button/DOWN ( ) button to select Country, and then OK ( )button to select country
-PVRFile system -
Press UP ( ) button/DOWN ( ) button to select PVR File system, and then OK ( )button to select Disk C
and press UP ( ) button/DOWN ( ) button to adjust.
-Restore FactoryDefault-
Press UP ( ) button/DOWN ( ) button to select Restore Factory Default, and then OK ( )button to select
sure or not.
-OSD AnimationRotation Only-
Press UP ( ) button/DOWN ( ) button to select OSD Animation Rotation, and then OK ( )button to select
on or only.
-OSD Time -
Press UP ( ) button/DOWN ( ) button to select OSD Time, and then OK ( )button to select 30s/60s etc.
-ECO Mode -
Press UP ( ) button/DOWN ( ) button to select ECO Mode and press UP ( ) button/DOWN ( ) button
button to select high/middle/low mode
-Blue Screen-
Press UP ( ) button/DOWN ( ) button to select Blue screen and OK ( )button to select on/off.
-Lock System-
Press UP ( ) button/DOWN ( ) button to select Lock System, and then OK ( )button to select on/off to
open and close the lock function.
-Set Password-
Press UP ( ) button/DOWN ( ) button to selectSet Password, and then OK ( )button to input old
password “0000 and set new password
-Block Program-
Press UP ( ) button/DOWN ( ) button to select Block Program, and then OK ( )button to enter the
submenu and then green button to choose lock/ unlock mode.
-ParentalGuidance-
Press UP ( ) button/DOWN ( ) button to select Parental Guidance, and then OK ( )button to select
off/4/5 etc.
www.liquifi.com.au -18 -
Press Source ( ) button selection USB mode to show Photo, Music, Film, Text. Press LEFT ( ) button / RIGHT
( )button to choose specific menu and the adjustable value. In the submenu, press UP ( ) button/DOWN
( ) buttonor LEFT ( ) button / RIGHT ( )button to choose menuitem.
-19 - www.liquifi.com.au
USBMenu
1. PHOTO Show
Select C:\，press OK ( ) button to enter submenu
1. Insert USB Port to USB entry.
2. Press LEFT ( ) button / RIGHT ( ) button to select photo, and then OK ( )button to enter submenu.
3. Select C:\，press OK ( )button to enter submenu.
4. Select the specific photo, and press USB PLAY ( ) button to play.
5. Press Exit ( ) button to exit.
2. MUSIC Play
Select C:\，press OK ( ) button to enter submenu
1. Insert USB Port to USB entry.
2. Press LEFT ( ) button / RIGHT ( ) button to select photo, and then OK ( )button to enter submenu.
3. Select C:\，press OK ( )button to enter submenu.
4. Select the specific photo, and press USB PLAY ( ) button to play.
5. Press Exit ( ) button to exit.
www.liquifi.com.au -20 -
3. FILM Play
Select C:\，press OK ( ) button to enter submenu
1. Insert USB Port to USB entry.
2. Press LEFT ( ) button / RIGHT ( ) button to select photo, and then OK ( )button to enter submenu.
3. Select C:\，press OK ( )button to enter submenu.
4. Select the specific photo, and press USB PLAY ( ) button to play.
5. Press Exit ( ) button to exit.
-21 - www.liquifi.com.au
4. TEXT Show
Select C:\，press OK ( ) button to enter submenu
1. Insert USB Port to USB entry.
2. Press LEFT ( ) button / RIGHT ( ) button to select photo, and then OK ( )button to enter submenu.
3. Select C:\，press OK ( )button to enter submenu.
4. Select the specific photo, and press USB PLAY ( ) button to play.
5. Press Exit ( ) button to exit.
Table of contents
Other Liquifi TV manuals
