Little Colorado Big Toy Chest User manual

Quality Wooden Children’s Furniture and Accessories
Made in America • Established 1987
www.littlecolorado.com
Big Toy Chest Assembly Instructions; Stock # 56
• Please inspect the parts for damage during shipping and for any missing items. If you suspect that there may be damage or a shortage, contact us
and we will send replacement parts if needed.
• As soon as components and hardware are unpacked; please remove all plastic bags from possible contact with children and recycle.
• Words in Red represent a component or hardware used in assembly.
• Illustrations are intended to help identify components and hardware and are not drawn to scale.
Revised 05/09
by
W.McClung
Please read instructions carefully
to avoid accidental damage to
components during assembly.
Toy Chest Hardware
• #6 Wood Screws
3/8 inch
Qty: 14
• #6 Trim Washers
Qty: 16
• #6 Wood Screws
1-1/4 inch
Qty: 16
Toy Chest Components
Page 1 of 3
Tools needed for assembly
• Screw Driver
Medium size #2 Phillips
ADULT ASSEMBLY REQUIRED
WARNING: Assembly kit contains parts with sharp points.
WARNING: Assembly kit contains parts with sharp edges.
WARNING: Package contains plastic bags that present suffocation risks for children.
WARNING: Assembly kit contains small parts that present choking hazards for children.
• Spring Lid Support
Qty: 1
Revised 5/15
by
E. Layton
• #8 Wood Screws
1/2 inch
Qty: 4
Lid
Front
Back
Side
Bottom
Side

Quality Wooden Children’s Furniture and Accessories
Made in America • Established 1987
www.littlecolorado.com
Big Toy Chest Assembly Instructions- Continued
Revised 06/14
by
E. Layton
Page 2 of 3
• Now that you have the front and
back fastened to the side; slide the
Bottom Panel in the panel groove
(The side with the Little Colorado
logo is the top side).
•Repeat steps 1 and 2 to attach
the remaining Side Panel.
• Be certain the bottom, front, and
back panels are fully located in the
grooves before tightening screws.
345
• Place Lid on top of the box and line
up existing marks located on outside
of the back panel to holes in hinge.
Attach hinge to back of box using (14)
#6 1/2 inch screws.
• Be careful not to over tighten screws.
Back
Panel
Lid
• Using the existing holes, attach bottom of
Lid Support to inside of Back Panel using
(2) of the #8 1/2 inch wood screws.
• Be careful not to over tighten screws.
Back
Top
Bottom
Lid Support
• Begin assembly with the Back Panel,
Front Panel and either one of the
Side Panels.
• Insert the Back Panel into the groove
on the Side Panel.
!Be sure to align the side and back panel
grooves so that the bottom panel will install
properly (see drawing in step 3).
• Use the Phillips head screwdriver to screw
(4) Trim Washers and (4) 1-1/4 Wood Screws
to attach both the Front and Back Panels
to the Side Panel.
12
Area of Detail
Back
Panel
Front
Panel
Bottom
Panel
Panel
Groove

Quality Wooden Children’s Furniture and Accessories
Made in America • Established 1987
www.littlecolorado.com
Big Toy Chest Assembly Instructions- Continued
Revised 06/14
by
E. Layton
Please Recycle Instructions
• Now that you have completed the assembly,
open and close the lid 10 times to break in the
lid support mechanism.
•The lid should not fall when the Lid Support is
properly installed.
• If the lid does not stay in position when raised,
please call us and we will help you. Until the lid
support is properly installed, do not allow
children to use this product.
• Carefully open lid straight up and rest it against
a stationary object (Wall, chair, etc.) Mount the
top part of the Lid Support to the inside of the
lid using the existing holes and (2) #8 1/2 inch
wood screws.
• It is very important that the existing holes line
up perfectly or the lid support may not function
properly.
•Be careful not to over tighten screws.
Lid
Back Panel
Taylor
67
If you would like your Toy Chest Personalized with
your child’s name. Contact us at 303 964 3212 and
we will take your order and mail you your child’s
name complete with mounting instructions.
If you have any problems, please call us and we will help you 303 964 3212 or email [email protected] 4450 Lipan St.,Denver, CO 80211
Page 3 of 3
Use and Care Instructions
If you received an unnished (raw plywood) Big Toy Box, it is highly recommended that a good quality paint, stain or clear coat be used to seal
the wood surfaces for the longest possible life.
The nish on this product is an environmentally friendly water base acrylic made by Sherwin Williams. It may be cleaned with a furniture polish,
lemon oil or a non abrasive cleaner using a soft cloth. DO NOT USE AMMONIA or products containing ammonia such as Windex glass or
multi-surface cleaner. Scuff marks can usually be removed by using a polishing compound sold at auto parts stores.
Little Colorado, Inc is a family run children’s furniture manufacturer located in Denver. Please check out www.littlecolorado.com to see our
other products that are all made here in America. The safety of your children is our highest concern. We are a GREEN company and hope you
will be able to recycle the packaging material that we used to ship your product.
If you have a comment or a question please contact us at info at [email protected]. All of us at Little Colorado hope you and your family
will enjoy this product for many years.
WARNING
Failure to properly install Lid Support
will result in an entrapment hazard.