Lloyd's CLW User manual
LLOYDS
W A T C H C O.
L
W
C
O P E R A T I N G
I N S T R U C T I O N S
L
W
C
L
W
C
S E R I E S
A
L
W
C
1
I N S T R U C T I O N S
1.0 P R O D U C T O V E R V I E W:
S E C O N D S H A N D
M I N U T E H A N D
D A T E W I N D O W
H O U R H A N D
1
2
3
D I A L
W I T H H O U R , M I N U T E & S E C O N D S M A R K E R S
C R O W N
2.0 W I N D I N G C R O W N:
1
2
3
The winding crown has 3 positions, as shown above. It is used to manually
wind the watch (Position 1), to set the date (Position 2) and to set the time
(Position 3).
2.1 W I N D I N G :
Your watch features a self-winding (automatic) movement. The movements
of your wrist sets a rotating mass in motion. This rotating motion tensions
the mainspring in the watches movement, the mainspring is responsible for
storing energy to power the watch.
Once you remove your fully wound watch, it will continue to run for up to
38 hours. It will then stop once all of the power reserve has been depleted.
The watch can be rewound manually, by hand (Position 1 - approximately
10 to 15 clockwise turns of the crown.)
CAUTION! It is recommended that you wind the watch before putting
it on. By doing so, you will avoid placing increased amounts of lateral
pressure on the winding stem, which over time could cause damage.
2.2 S E T T I N G T H E D A T E :
The date is indicated inside the date window, located at 3 o’clock on the
dial of your watch. To set the date, carefully pull the crown out to Position 2.
Rotate the crown clockwise to scroll through the dates until reaching your
desired date.
Once set, simply return the crown back to Position 1.
CAUTION! The date mechanism is blocked between 10p.m. and 2a.m. If
you need to change the date, please do so between 2a.m. and 10p.m.
Failure to do so could cause damage to the date mechanism of your watch.
It is recommended that you set the date on your watch before putting
it on. By doing so, you will avoid placing increased amounts of lateral
pressure on the winding stem, which over time could cause damage.
2.3 S E T T I N G T H E T I M E :
In order to set the time on your watch, carefully pull the crown out to Position 3.
Rotate the crown until the correct time is displayed by the Hour and Minute
hands.
Once set, simply return the crown back to Position 1.
CAUTION! It is recommended that you set the time on your watch before
putting it on. By doing so, you will avoid placing increased amounts of lateral
pressure on the winding stem, which over time could cause damage.
If you find the mechanism disengages whilst you are setting the time, return
the crown to position 1. Once returned, pull the crown back out to Position 3
and resume setting the time.
T A K I N G C A R E
O F Y O U R W A T C H
3.0 C E R T I F I C A T E O F A U T H E N T I C I T Y:
Your Lloyds Watch Co. timepiece is delivered with a Certificate of Authenticity,
which indicates the model designation, serial no., date of manufacture and
date of sale of your watch.
The certificate is only valid if it is signed and dated by Jordan Lloyd - Owner
& Founder of Lloyds Watch Company Ltd. It must also bare the Lloyds Watch
Co. stamp of approval.
This certificate guarantees the authenticity of your timepiece as a genuine
Lloyds Watch Company product.
3.1 C L E A N I N G Y O U R W A T C H:
Your Lloyds Watch Co. timepiece is also delivered with a branded micro fibre
cleaning cloth. It is recommended that you keep your watch clean by using
this cleaning cloth. Should your watch become contaminated through day to
day usage, gently wipe the micro fibre cloth over the watch to remove all dirt.
Care must be taken in order to remove large surface contaminants before
wiping the watch. Failure to do so may result in you accidentally scratching
your watch.
CAUTION! In an attempt to clean your watch, please do not place it directly
under running water. This can subject the seals of your watch to accelerated
stress and could comprimise the water resistance of your watch. The cleaning
method stated above will be more than adequate enough.
3.2 A C C U R A C Y:
The following rate of accuracy has been stated by the manufacturer of your
watches automatic movement:
‘Plus or Minus 20 seconds over a period of 24 hours.’
The limit values are subjected to interpretation: 95% of the pieces delivered in a lot must be within the specified limits.
The precision of a mechanical watch is determined by how accurately it keeps
time. A watch that appears to be running fast or slow is considered precise if
the amount of time of which is gained or lossed remains constant. Such
deviation can be easily corrected, if needed. Your temperature or the nature of
your physical activity can cause such irregularities. Changes in temperature or
air pressure, the presence of magnetic fields (as produced by most electronic
devices) as well as vibrations, shock and other factors may affect your watches
accuracy.
Should you notice that your watch exhibits irregularities in its time keeping,
please get in contact. If the watch is deemed at fault it may be returned
to Lloyds Watch Co. for a full inspection.
3.3 W A T E R R E S I S T A N C E:
Your Lloyds Watch Co. timepiece has a water resistance rating of 3ATM.
Although your watch carries this water resistance rating, it is recommended
that you do not carry out activities such as swimming or showering whilst
wearing your watch. Activities such as these can increase the water pressure
acting on the seals in your watch and cause them to fail.
Your watch is assembled with a number of seals to protect the movement
against the ingress of dust and moisture during day to day usage.
L
W
C
Should you have any further questions, or require more
information regarding the operation and maintenance
of your watch. Please do not hesitate to contact us.
M O V E M E N T
S P E C I F I C A T I O N
4.0 S P E C I F I C A T I O N O F T H E M O V E M E N T:
Self-Winding (Automatic) Mechanical Movement
Swiss Made
Calibre Sellita SW200-1
----------------------------------------------------------------------------------------------------
Diameter 25.00mm
----------------------------------------------------------------------------------------------------
Height 4.60mm
----------------------------------------------------------------------------------------------------
Number of Jewels 26
----------------------------------------------------------------------------------------------------
Power Reserve 38 hours
----------------------------------------------------------------------------------------------------
Frequency 28 800 A/h (4 Hz)
----------------------------------------------------------------------------------------------------
Displays:
Hour and Minute hands for local time
----------------------------------------------------------------------------------------------------
Subsidiary Displays:
Date at 3 o’clock
L
W
C
Document Issue - V1.0
March 2015
