Logic PNM-220 User manual

Technical Manual 1.00, PNM-220
Technical Manual for the
PNM-220
Version 1.00
Logic IO ApS. Ph: ([phone]
Ho mboes A é 14 Fax: [phone]
8700 Horsens Emai : info@ ogicio.com
Denmark www. ogicio.com / www.rtcu.dk
Page 1 of 16

Technical Manual 1.00, PNM-220
Introduction
The Logic IO PNM-220 is a comp ete so ution using the Navigation and Messaging
P atform designed for the most demanding and professiona f eet management
app ications. The PNM-220 device is a ruggedized 7-inch, easy to read, screen optimized
for finger touch usage. A powerfu processor and generous RAM and f ash ensure a
de ightfu experience. The PNM-220 a so offers support for connecting up to two cameras
used for rear-view or cabin view etc.
The PNM-220 comes with the PNM software/maps pre-insta ed and interface cab es for
the RTCU MX2i pro/pro+. Ready to go!
This technica manua describes the insta ation of the PNM-220, and the technica detai s
of the system. For contro ing the PNM device from the VPL user app ication, p ease refer
to the RTCU on ine he p, and for detai ed information on the NMP software interface,
p ease refer to the documentation of the Navigation and Messaging P atform.
The NMP software and the Sygic maps are pre-insta ed on the PNM device and activated
according to the user agreement. P ease refer to the NMP software documentation for
detai ed information.
Logic IO ApS. Ph: ([phone]
Ho mboes A é 14 Fax: [phone]
8700 Horsens Emai : info@ ogicio.com
Denmark www. ogicio.com / www.rtcu.dk
Page 2 of 16

Technical Manual 1.00, PNM-220
Table of Contents
Introduction.............................................................................................................................2
Tab e of Contents...................................................................................................................3
Graphica view........................................................................................................................4
Package overview..................................................................................................................5
PNM-220 Overview............................................................................................................6
Typica System Connection................................................................................................8
Typica App ication.................................................................................................................9
Interfacing to the RTCU MX2i Pro/Pro+.............................................................................9
Ana og camera interface..................................................................................................10
Interfacing to the RTCU IDE Simu ator................................................................................11
Technica Specifications......................................................................................................12
Appendix A – Mounting the dashboard bracket...................................................................13
Appendix B – Insta ation and remova of the SD card........................................................15
Logic IO ApS. Ph: ([phone]
Ho mboes A é 14 Fax: [phone]
8700 Horsens Emai : info@ ogicio.com
Denmark www. ogicio.com / www.rtcu.dk
Page 3 of 16

Technical Manual 1.00, PNM-220
Graphical vie
Logic IO ApS. Ph: ([phone]
Ho mboes A é 14 Fax: [phone]
8700 Horsens Emai : info@ ogicio.com
Denmark www. ogicio.com / www.rtcu.dk
Page 4 of 16

Technical Manual 1.00, PNM-220
Package overvie
The PNM-220 package inc udes the fo owing items:
Quantity Item Description
1 PNM-220 device Windows CE6.0 device.
1 Mounting Bracket PNM-220 device mounting bracket
1 8 GB SD-CARD With pre-insta ed software.
Typica y a ready insta ed in the PNM-220
device.
1 PNM-220 series device cab e Connection cab e between PNM device and
the PNM interface box
Logic IO ApS. Ph: ([phone]
Ho mboes A é 14 Fax: [phone]
8700 Horsens Emai : info@ ogicio.com
Denmark www. ogicio.com / www.rtcu.dk
Page 5 of 16

Technical Manual 1.00, PNM-220
PNM-220 Overvie
Interface Description
Power No bui t-in functiona ity. May be used for power by the app ication.
SET User-defined key.
Key 1 User-defined key.
Key 2 User-defined key.
Key 3 User-defined key.
Key 4 User-defined key.
LEDs 1 power LED and 3 status LEDs
Touch Screen To interact with the app ication using finger touch or attached sty us
P ease note that a the keys and the status LEDs on the PNM-220 device can be
configured by the VPL app ication. P ease refer to the RTCU IDE on ine-he p for further
information.
Logic IO ApS. Ph: ([phone]
Ho mboes A é 14 Fax: [phone]
8700 Horsens Emai : info@ ogicio.com
Denmark www. ogicio.com / www.rtcu.dk
Touch
Screen
Power
Set Key2Key1 Key3 Key4
Speaker Speaker
LEDs
Page 6 of 16

Technical Manual 1.00, PNM-220
Interface Description
Reset Button Reset button of the PNM-220 device
Sty us Sty us for the touch screen
Interface Cab e
Connector
The connector for the PNM-220 device interface cab e
SD card compartment
Cover
The cover for the compartment where the SD card reader is
ocated.
The PNM-220 device can be reset asynchronous y using the reset button, ocated at the
backside of the device. P ease do not use the button un ess it is abso ute y needed.
The sty us can be used for more accurate hand ing of the touch screen. As the touch
screen is resistive, a finger can be used as we . The sty us is mounted tight y at the
backside of the device. It can be removed by s iding it out sideways.
Logic IO ApS. Ph: ([phone]
Ho mboes A é 14 Fax: [phone]
8700 Horsens Emai : info@ ogicio.com
Denmark www. ogicio.com / www.rtcu.dk
Mounting
Jack
Sty us
Interface
Cab e
Connector
USB and
SD Card
Cover
Reset
Button
Page 7 of 16

Technical Manual 1.00, PNM-220
Typical System Connection
A typica system insta ation is i ustrated be ow:
The app ication in the RTCU unit contro s the power to the PNM device.
Un ike the other PNM devices with externa interface box, this device wi on y shut down
direct y whi e it is communicating with the RTCU. If asked to shut down whi e the
connection is ost, it wi either wait for a timeout1 before shutting down, or it can be
manua y shut down by pressing the reset button on the back. Note that the reset button
shou d not be used un ess abso ute y necessary, as it cuts the power immediate y, whi e
the two other ways a ows the device to perform a contro ed shut down.
1 See the setting DisconnectTimeout in the Navigation and Messaging P atform User Guide.
Logic IO ApS. Ph: ([phone]
Ho mboes A é 14 Fax: [phone]
8700 Horsens Emai : info@ ogicio.com
Denmark www. ogicio.com / www.rtcu.dk
Page 8 of 16
RTCU Unit
Externa
Power Supp y

Technical Manual 1.00, PNM-220
Typical Application
This is a quick start guide to connect the PNM device to the supported RTCU units. It is
easy to insta the PNM system on ocation with the supp ied cab e for the RTCU MX2i
pro/pro+. The fo owing section wi describe the system connection to the supported
RTCU units.
Interfacing to the RTCU MX2i Pro/Pro+
The data cab e with the RJ-45 connector needs to be connected to the 8-po e seria port 2
connector on the RTCU unit. The power cab e, with the read and b ack wires at the end,
must be supp ied from an externa DC supp y.
An examp e of the connection to RTCU MX2i pro is shown in the drawing be ow.
1. Connect the PNM device interface cab e to the PNM device.
2. Connect the RJ-45 data cab e of the PNM device interface cab e to the seria Port 2
of the RTCU MX2i pro.
3. Connect the power supp y to the power connector cab e. The power requirement is
9..32VDC. The b ack wire is (-) and the red wire is (+).
Note that the power to the PNM device is contro ed by the RTCU MX2i pro
app ication. The modu e wi not power on un ess the RTCU MX2i pro is powered on
and the app ication enab es the modu e. P ease refer to the RTCU IDE on ine he p
for enab ing and using the NMP interface.
Logic IO ApS. Ph: ([phone]
Ho mboes A é 14 Fax: [phone]
8700 Horsens Emai : info@ ogicio.com
Denmark www. ogicio.com / www.rtcu.dk
Page 9 of 16
9..32VDC
Data cab e
Power cab e

Technical Manual 1.00, PNM-220
Analog camera interface
PNM-220 offers connection for up to two ana og cameras using the BNC connectors
avai ab e at the PNM device interface cab e. Ana og camera #1 must be connected to the
cab e abe ed with BNC-1 and ana og camera #2 must be connected to BNC-2.
The use of the cameras is under fu contro of the VPL app ication. P ease consu t the
RTCU IDE on- ine he p for additiona information.
Logic IO ApS. Ph: ([phone]
Ho mboes A é 14 Fax: [phone]
8700 Horsens Emai : info@ ogicio.com
Denmark www. ogicio.com / www.rtcu.dk
Page 10 of 16

Technical Manual 1.00, PNM-220
Interfacing to the RTCU IDE Simulator
The PNM-220 is supported by the RTCU IDE Simu ator. In order to connect the PNM-220
series device to the PC, an optiona cab e with the order code RT-PNM-PC is needed.
1. Connect the PNM device interface cab e to the PNM device.
2. Connect the RJ-45 data cab e of the PNM device interface cab e to the combiner.
3. Connect the combiner with one of the avai ab e seria ports on the PC with the
PNM-220 PC interface cab e.
4. Connect the power supp y to the power cab e. The power requirement is 9..32VDC.
The b ack wire is (-) and the red wire is (+).
Note that the power to the PNM device is contro ed by RTCU IDE app ication. The
modu e wi not power on un ess the RTCU IDE Simu ator is running and the user
app ication enab es the modu e. P ease refer to the RTCU IDE on ine he p for
enab ing and using the NMP interface.
Logic IO ApS. Ph: ([phone]
Ho mboes A é 14 Fax: [phone]
8700 Horsens Emai : info@ ogicio.com
Denmark www. ogicio.com / www.rtcu.dk
Page 11 of 16
9..32VDC
Power cab e
Data cab e PC Cab e

Technical Manual 1.00, PNM-220
Technical Specifications
Logic IO ApS. Ph: ([phone]
Ho mboes A é 14 Fax: [phone]
8700 Horsens Emai : info@ ogicio.com
Denmark www. ogicio.com / www.rtcu.dk
Page 12 of 16

Technical Manual 1.00, PNM-220
Appendix A – Mounting the dashboard bracket
A dashboard mounting bracket is inc uded for easy insta ation of the PNM-220 device. In
the fo owing the mounting of the bracket wi be described.
1. Loosen the adjustment screw hand e, and set the bracket arm to an upraised
position
2. Loosen the securing screw unti there is a gap between the bracket part and the
meta p ate.
3. P ace the meta part on top of the bracket at the starting point of the mounting jack
on the back side of the PNM device. S ide the bracket part unti it is at the desired
position. Fasten the securing screw. P ease note the orientation of the bracket
Logic IO ApS. Ph: ([phone]
Ho mboes A é 14 Fax: [phone]
8700 Horsens Emai : info@ ogicio.com
Denmark www. ogicio.com / www.rtcu.dk
Bracket
Adjustment
screw hand e
Page 13 of 16

Technical Manual 1.00, PNM-220
4. The vertica ang e and rotation of the PNM device can be adjusted using the screw
hand e on the bracket.
5. Remove the protection paper of the adhesive and p ace the bracket on a proper
ocation at the dashboard. P ease make sure that the bracket is mounted on the
correct ocation with the correct ang e.
Logic IO ApS. Ph: ([phone]
Ho mboes A é 14 Fax: [phone]
8700 Horsens Emai : info@ ogicio.com
Denmark www. ogicio.com / www.rtcu.dk
Mounting jack
Mounting jack
starting point
Securing
screw
Page 14 of 16

Technical Manual 1.00, PNM-220
Appendix B – Installation and removal of the SD card
The SD card reader is hidden in a compartment for protection purpose.
Access the compartment with the SD-CARD reader as fo ows:
1. Unscrew the two M2 screw from the compartment cover.
2. Pu up the cover s ight y unti you see the gap.
3. Take out the cover
P ease note that the compartment on the opposite side of the termina is reserved and
shou d not be accessed.
For c osing the cover, p ease fo ow the steps above at reverse order.
Logic IO ApS. Ph: ([phone]
Ho mboes A é 14 Fax: [phone]
8700 Horsens Emai : info@ ogicio.com
Denmark www. ogicio.com / www.rtcu.dk
gap
Pu up
Pu out the cover
Page 15 of 16

Technical Manual 1.00, PNM-220
A side view of the termina when the cover is removed is as fo ows:
Interface Description
Mini USB Port Mini USB 2.0 service port.
USB Port USB host port.
Earphone jack Connection with a stereo earphone
SD card s ot SD card reader for app ication / map card inc uded with the product.
Logic IO ApS. Ph: ([phone]
Ho mboes A é 14 Fax: [phone]
8700 Horsens Emai : info@ ogicio.com
Denmark www. ogicio.com / www.rtcu.dk
Mini USB port
USB port
Earphone
jack
SD card
s ot
Page 16 of 16