Love For Sleep DENISE User manual
Copyright © 2017 - 2018 by LOVE FOR SLEEP LTD All rights reserved.
DENISE / JACOB
Do not use the bed if any part is broken, or missing.
ROUTINE CARE & MAINTENANCE
WARNING:
WARNING:
PAGE 2 OF 22
Due to constant updating and improvements, some components may occasionally dier
slightly from the images shown in these instructions. We reserve the rights to change the
specifications of any products without prior notice. If you need any assistance please
contact your retailer from whom you purchased your product, who will take appropriate
action.
To ensure that your cot bed is used in accordance with these instructions, please read them
fully.
Be aware of the risk of open re and other sources of heat, such as elec-
tric bar res, gas res, etc. in the vicinity of the under cot bed drawer.
All assembly ttings should be tightened properly and care should be taken to ensure that
no drawstrings, necklaces) this could lead to strangulation. Regularly check that all ttings
and components of the under cot bed are fully tightened and in working order.
Standing in, or using the cot bed other than for its intended purpose, could cause damage to
the structure or serious injury to your child. Wood is a natural material, the colour will darken
with age.
For cleaning, use only a mild detergent and warm water.
Do not use bleach.
Do not use any abrasive substances.
Take care when handling or moving furniture, careless handling can
damage wooden furniture.
PAGE 3 OF 22
0 - 6
months 6 - 12
months
+12
months
FROM A
NEWBORN
TO TODDLER
LEVEL 1
LEVEL 2
LEVEL 3
Part 1
x12
Part 2
x 12
Part 4
x 1
Part D
Part B
Part A
Part E
Part F
Part G
Part C
Part G(drawer) shall be assembled according to instructions from page 13.
NOTE:
Part 3
x 8
PAGE 4 OF 22
Part 5
x 8
Part 6
x 7
PAGE 5 OF 22
CLOSE BED
Part 1
x12
Part 2
x 12
Part 4
x 1
Part D
Part B
Part A
Part E
Part F
Part G
Part C
Part 3
x 8
STEP 1
PAGE 6 OF 22
2
B
D
C
4
1
1
1
1
2
2
Push nut #2 into the slots located in parts C, D. Hold nut #2 in place by using a at head
screwdriver and make sure that nut #2 is correctly positioned to allow the screw #1 to be
threaded through. Screw the panels Binto the sides Cand Dusing Swedish screws #1 and
Allen key #4.
1
2
2
STEP 2
PAGE 7 OF 22
Screw the panels A into the sides Cand Dusing Swedish screws #1 and Allen key #4. Hold
nut #2 in place by using a at head screwdriver and make sure that nut #2 is correctly
positioned to allow the screw #1 to be threaded through.
2
4
1
A
1
2
1
1
1
2
2
2
STEP 3
Push plastic bolts #3 into the cot slots. The cover cannot be used when the slats are on the
lowest or middle position on the cot.
3
3 3
3
3
3
3
3
3
PAGE 8 OF 22
STEP 4
PAGE 9 OF 22
Push the drawer cover Finto the frame. White colour to the top of bed.
F
STEP 5
PAGE 10 OF 22
Push the part Einto the frame.
for very small children for older children
Bottom can be mounted at tfree dierent
NOTE:
for small children
E
STEP 7
PAGE 11 OF 22
Push the assembled drawer ( part G) into the drawer runners under the assembled cot.
G
STEP 8
PAGE 12 OF 22
Installation completed.
PAGE 13 OF 22
Part 5
x 8
Part 6
x 4
Part I
Part J
Part L
Part K
Part N
Drawer
PAGE 14 OF 22
STEP 1
STEP 2
5
5
I
L
6
6
L
K
J
5
5
5
5
5
5
5
5
6
4
PAGE 15 OF 22
STEP 3
STEP 4
N
I
6
4
6
6
PAGE 16 OF 22
STEP 5
Draw installation completed.
PAGE 17 OF 22
OPEN BED
Part D
Part B
Part A
Part E
Part F
Part G
Part H
Part 1
x12
Part 2
x 12
Part 4
x 1
Part 3
x 8
Part 5
x 8
Part 6
x 7
PAGE 18 OF 22
WARNING: Board barrier can be use only in case where bottom is located on the
lowest position on the cot.
Board barrier
Part 6
x 3
Part 4
x 1
Part H
PAGE 19 OF 22
7
1
Remove screws #1 from one side using Allen key #7. Remove side panel.
PAGE 20 OF 22
STEP 10
H
Push the board barrier Hinto the frame. Board barierr can be mounted at right and left
position also.
H
This manual suits for next models
1
Table of contents
