Lu ÜNO User manual

ÜNO/DÜO
Installation Instructions
Revision
English
October 2020
V2

Lü Installation Installers Policies
Not included items
Technical specications (light & sound module)
Installation conguration (UNÖ & DUÖ)
ÜNO - Connection’s diagram (Top view)
DÜO with additional lighting unit
Installation rigging (Lighting Module - GYM (D))
Installation rigging (Lighting module - Palestra (D))
Installation – Projector Alignment I
Installation rigging (Projection module (F))
Installation – Camera Calibration K
Installation – Camera Calibration L
Installation rigging (Cables (H))
Installation – Light & sound M & N
Acceptation of installation O
Package Contents
Technical specications (Camera & projector module)
Technical specications (Heart module)
Installation conguration (Side view)
DÜO - Connection’s diagram (Top view)
Installation conguration - Step by step (A to C)
Installation – System Statup J
Installation rigging (Heart module (G))
Complete Components Documentation
Page 3
Page 5
Page 7
Page 9
Page 11
Page 10
Page 13
Page 15
Page 16
Page 21
Page 18
Page 23
Page 20
Page 25
Page 26
Page 4
Page 6
Page 8
Page 12
Page 14
Page 17
Page 22
Page 19
Page 24
Page 27
About this guide Page 2
Table of contents
Installation rigging (Camera module (E))

About this guide Disclaimer
Important safety Instruction
The Lü interactive system installation manual
provides basic product information such as safety
and operation.
The information and specications contained in this
installation manual are
subject to change without notice.
IMPORTANT : Do not modify this product! Changes or modications not expressly approved by the
manufacturer could void the user’s warranty.
Do not use this system near water.
Clean only with a dry cloth.
Do not block any ventilation openings.
If mounting the product overhead, make sure there is adequate support for the product’s weight and always
secure the product to the structure using a safety cable. Install the product following best practices and in
accordance with local laws and regulations.
Only use accessories specied by the manufacturer.
Only plug this system after installation is completed and proper verication.
Always connect the product to a grounded circuit.
Do not use the Lü system in an environment where temperatures exceed +40 °C (104 °F).
Refer all servicing to qualied service personnel. Servicing is required when the system has been damaged
in any way, such as power-supply cord or plug is damaged, liquid has been spilled, objects have fallen
into the system, the system has been exposed to rain or moisture, does not operate normally, or has been
dropped.
To completely disconnect AC power from the system, shut down the computer properly, the power supply
cord must be unplugged from the ceiling and the circuit breaker on-off position.
Lü loudspeakers are easily capable of generating sound pressure levels sucient to cause permanent
hearing damage to anyone within normal coverage distance. Caution should be taken to avoid prolonged
exposure to sound pressure levels exceeding 90 dB.
Page 2
01
06
07
11
08
10
09
02
03
05
04

Lü Installation Installers Policies
Responsibility
Lü Interactive Playground Inc. is committed to provide a product that has been fully tested and was fully functional
at the time it was inspected in its Canadian warehouses.
It is the buyer’s responsibility to validate the condition of the product upon receiving it.
The installer assumes all liability resulting from accidents or damage to the product that occurred during the
installation process. In particular, they will be responsible for the repair and shipping costs for the spare parts.
The methods used, the procedures followed and the safety measures put in place during the installation
engage the responsibility of the installer, and this, for the total lifetime of the product.
For any further questions, information or validations, please contact our facility coordination
team at [email protected].
Page 3

Page 4
Heart module
Lü management system.
Camera module
3D camera system.
1 Lü system remote
controlle
Light & sound module
6 200 watts LED spotlights
to manage the ambient
lighting and general colors, 2
motorized LED light xtures
for special light effects and 1
powerful 2000 watts sound
system.
Stabilization cables system
1 remote protection case Headset Microphone
Xvive U3
Projection module
5500 lumens WXGA projector
protected in a custom
enclosure.
1 projector’s remote controller
Package Contents
Each ÜNO/DÜO conguration consist of:

What is not in the box but required for the installation
The following items are not included in the box
All the material needed for structural hanging on the ceiling depending of construction type (ex. Cantruss,
1/2” [13 mm] threaded rod, bolts and nuts, etc.).
Security steel cables and fasteners to secure components directly to building structure, second safety,
3/16” (5 mm) cable for the main unit and 3/32” (2.5 mm) cable for the projector (length to be determined by
the installer).
Self-drilling #8 2/3” (19 mm) metal screws (3 minimum).•
Lift system for persons (ex. scissor lift or scaffolding).
Tools (cable cutter, hex key [5 and 6 mm], wrench [7/16” and 3/4” at minimum], portable band saw and
small angle grinder with metal cutting wheel).
DN 40 (1 1/2”-11.5 NPS) threaded pipe for hooking the projector module (length to be determined by the
height of ceiling; the bottom part of the projector should be at 20’ [6 m] from ground).
DN 40 (1 1/2”-11.5 NPS) threaded pipe for hooking the camera module (length to be determined by the
height of ceiling; the bottom part of camera should be at 18’ [5.5 m] from ground).•
2 celling plates (6 x 6” [150 x 150 mm]) or 8 x 8” [200 x 200 mm]) for receiving the projector and camera
threaded pipes.
1 12’ (3 m) RJ45 network cable.
Pump to inate balls.
For the DÜO unit, 2 +50’ (15 m) XLR cables (male-to-female) to connect the two units together.
Page 5
01
06
07
11
08
09
02
03
05
04
10

Technical specications
Page 6
Camera module Projector module
15 pi from the wall / 18 high
6” x 4” x 5”
1.5” pipe mounting bracket
or screw on the ceiling
3.05 lb (1.38 kg)
110-240V - 36W (0.3Amp)
ÜNO conguration
Installation position*
Size (L x W x H)
Rigging
Weight
Power consumption
28 pi from the wall / 20 pi high
22” x 20” x 16”
1.5” pipe mounting bracket
37 lb (16.78 kg)
110-240V - 470W
IMPORTANT : The installation parameters in this guide are optimal recommendations. These may change
or vary depending on the installation context or space. Contact us for more information on the matter.

Page 7
With speaker Without speaker
16’ from the wall / 20’ high
37” x 76” x 15”
4 hanging points
178 lb (80.74 kg)
110-240V - 1106 W (9.21A)
16 pi du mur
37’’ x 46” x 15’’
Screw on the ceiling
99 lb (44.91 kg)
110-240V - 674 W (5.62A)
Light and sound module
IMPORTANT : The installation parameters in this guide are optimal recommendations. These may change
or vary depending on the installation context or space. Contact us for more information on the matter.
Technical specications
Installation position*
Size (L x W x H)
Rigging
Weight
Power consumption

Page 8
Heart module
12 inches over the projection (centered)
14” x 23” x 5”
Screw on the wall
18 lb (8.16 kg)
110-240V - 216W (1.8A)
Technical specications
Heart module
IMPORTANT : The installation parameters in this guide are optimal recommendations. These may change
or vary depending on the installation context or space. Contact us for more information on the matter.
Installation position*
Size (L x W x H)
Rigging
Weight
Power consumption

Installation conguration
Page 9
Lü can be sold in two different congurations. The ÜNO conguration broadcasts on an interactive wall while the
DÜO conguration includes two ÜNO units projecting on two interactive walls face to face or side by side. All it
takes is a few minor tweaks and additional connections to allow for a synchronized experience occupying the
entire gym.
ÜNO & DÜO
Heart module
Camera module
Light and sound module
Projector module
ÜNO
DUÖ
A
B
D
C
ABD C
A A
B B
D D
C C

Installation conguration
Page 10
All units must be mounted to the ceiling and aligned according to the projection surface. The diagram below
shows the optimal position. Some exceptions for special environments can be made, within the exibility margins
(maximum tolerance).
Side view
Flexibility margin
(maximun tolerance)
19’ (5.8 m) wide
10’ 7” (3.3m) high
Max projection surfaceOptimal position

ÜNO - connection’s diagram
Page 11
Connect modules 1, 2, 3 and 4 using this diagram
Top view
Cable 110 volt s
HDMI Cable
Cables XLR Speaker s
Cables USB Camer a
Cable DMX Ligh t
Network Cables (not pr ovided)
10 pieds (10 m )
65 pieds (20 m )
25 pieds (7.5 m)
30 pieds (10 m )
25 pieds (7.5 m)
10 pieds (10m)
Electrical Outlet (110 volts)
Network Outlet

DÜO - connection’s diagram
Page 12
Top view
IMPORTANT : The two computers must be connected on the same network for the DÜO system to work.
Only one DÜO system per network.
Connect modules 1, 2, 3 and 4 using the ÜNO connection’s diagram
nter-connect the two light modules together using this diagram
01
02
Male Female

DÜOwith additional lighting unit –Connection’s diagram
Page 13
Connect modules 1, 2 and 3 using the ÜNO connection’s diagram
Inter-connect the three light modules together following this diagram
Top view
01
02
IMPORTANT : The two computers must be connected on the same network for the DÜO system to work.
Only one DÜO system per network.
Male Female

Installation conguration
A. Choose the best projection location on the wall (center and 4 corners)
The recommended width is 19’ (5.8 m) and the recommended height is 10.7’ (3.3 m). For the ideal position, the
lower end of the screen should be placed at 12” (20 cm) from the oor.Minimal height is 8” (20 cm) from the oor
and maximal height is 16” (40 cm) from the oor.
B. Mark the 4 corners of the surface of your projection screen on the wall and the position of the Heart, which
is to be centered 8 to 12” higher than the projection
Make sure to always to always have a 16:9 ratio for the screen..
C. Determine the position of the various modules on the ceiling by measuring the distances from the
projection wall and install the structural suspension elements
Ideally, all modules should be centered in front of the projection wall
Page 14
Step by step (A to C)
Camera module
Install at 18’ (5.5 m) from the oor and at 16’ (4.9 m) from the wall.Flexibility margin
(maximum tolerance): 12’ (3.65 m) to 18’ (5,5 m) from the oor and 15’ (4.6 m) to 16’
(4.9 m) from the wall. Maximum distance between the camera and the farthest corner
of projection should not exceed 23’ (7 m). The module can be offset ±3’ (1 m).
Projection module
Install at 20’ (6 m) from the oor and at 28’ (8.5 m) from the wallFlexibility margin
(maximum tolerance): 28’ (8.5 m) to 40’ (12.2 m) from the wall (if installed at
recommended height). The module can be offset by ±3’ (1 m).
Light & sound module
Install at 20’ (6 m) from the oor and at 16’ (4.9 m) from the wall.Flexibility margin
(maximum tolerance): 12’ (3.65 m) to 26’ (8 m) from the oor and 16’ (4.9 m) to 18’
(5.5 m) from the wall. The module can be offset by ±1’ (30 cm).
Heart module
Install between 8” (20 cm) and 12” (30 cm) above the projection surface centered.

D. Lift and install the lighting module in place, as follows:
Make sure the base is installed in the direction indicated by the sticker.
Hang the mounting base with the threaded rods, making sure the bolts are doubled.
Disconnect and then unscrew the two moving lights from the lighting tray with an 8 mm socket (so that the
weight of the module is under 23 kg [50 lbs] for a safe single-person installation).
Insert the light tray inside the mounting base on side 1 (green) rst and push on side 2 (red)
until it locks into place.
Screw the light tray to the mounting base with the 8 bolts provided with a 13 mm socket.
Screw the moving lights inside the lighting tray and reconnect their respective cables so that they are working.
Screw the speaker brackets to each side of the mounting base using 8 bolts per bracket and a 13 mm socket.
Screw for the safety eyelets in the center of the speaker brackets and install the safety cables from the eyelets
to the building structure.
Install the speakers on the brackets by sliding the nuts through the eyelets downwards. Then tighten the nuts
with a 13 mm socket.
Attach speaker safety carabiners to the safety eyelets.•
Pass the 48” (122 cm) IEC cables through the mounting base, one on each side, and connect them to the
speakers.
Page 15
06
07
08
10
11
09
02
03
05
04
Installation rigging
Lighting Module - GYM (D)
01
* Safety cable
minimum requirements:
840 lbs (380 kg),
size 3/16” (5 mm)
(length to be determined)
Mount the unit making
sure the “A” side is facing
the interactive projection
wall.
A
A

D. Lift and install the lighting module in place, as follows:
Make sure the base is installed in the direction indicated by the sticker.
Hang the mounting base with the threaded rods, making sure the bolts are doubled.
Screw the mounting base directly to the ceiling using 8 screws appropriate for the structure.
Disconnect and then unscrew the two moving lights from the lighting tray with an 8 mm socket
(so that the weight of the module is under 23 kg [50 lbs] for a safe single-person installation).
Insert the light tray inside the mounting base on side 1 (green) rst and push on side 2 (red) until it locks into
place.
Screw the light tray to the mounting base with the 8 bolts provided with a 13 mm socket.
Screw the moving lights inside the lighting tray and reconnect their respective cables so that they are working.
Unscrew the 6 nuts on each of the projector brackets and tilt the bottom bracket 90 degrees and put back the
bolts and nuts, so the bracket orientation can be adjusted.
Install the speaker brackets on either side of the projection screen at least 8’ (2.4 m) from the ground or above
the projection screen on either side of the Heart module.
Install the speakers on the brackets by sliding the nuts through the eyelets downwards. Then tighten the nuts
with a 13 mm socket.
Set the angle of the brackets, and tighten the nuts.
Connect speakers to the power outlet with the 10’ (3 m) IEC cables.
Page 16
06
07
08
10
11
12
09
02
03
05
04
Installation rigging
Lighting module - Palestra (D)
01
* EXIGENCE MINIMALE
DU CÂBLE DE SÉCURITÉ
840 lb (380 kg),
taille de 3/16 po (5 mm)
(longueur à déterminer)
Montez l’unité en vous
assurant que le côté « A »
est orienté vers le mur de
projection interactif.
A

E. Lift and install the camera module
Stabilization cables systems (to be used on all pipes longer than 24” [60 cm])
Secure the camera module using the ceiling plate and a DN 40 (1 1/2”-11.5 NPS) threaded pipe (length to be
determined by the ceiling height; the bottom of the camera should be at 18’ [5,5 m] from ground).
Use a self-drilling screw at the ceiling plate to block any pipe rotation.
Connect power cords (1 connector) into the light module power strip.
Install the ring on the pipe at 1/3 of the length of the pipe from the camera.
Install all 3 metal cables at 120 degrees angle towards the structure in the ceiling.
Stretch rmly the 3 cables with the turnbuckles until the pipe is stabilized at 90 degrees from the ceiling in
all directions and rmly holds in place.
Page 17
02
02
03
03
Installation - Rigging
Camera module (E)
01
01
Note: The camera
rotation bracket will
be locked later during
calibration.
Ceiling mount with a DN
40 (1 1/2”-11.5 NPS)
threaded pipe
AA A

Stabilization cables systems (to be used on all pipes longer than 24” [60 cm])
Secure the projector module using the ceiling plate and a DN 40 (1 1/2”-11.5 NPS) threaded pipe (length to be
determined by the ceiling height; the bottom of the camera should be at 20’ [6 m] from ground).
Use a self-drilling screw at the ceiling plate to block any pipe rotation.
Install a safety cable from the eye bolt located between the top of the projector module and the structure.
Install the ring on the pipe at 1/3 of the length of the pipe from the camera.
Install all 3 metal cables at 120 degrees angle towards the structure in the ceiling.
Stretch solidly the 3 cables with the turnbuckles until the pipe is stabilized at 90 degrees from the ceiling
in all directions and rmly holds in place.
Page 18
02
02
03
03
Installation - Rigging
Projection module (F)
01
01
* Safety cable minimum
requirements: 125 lbs
(55 kg), size 3/32”
(2.5 mm) (length to be
determined)
Note: The projector
rotation bracket will be
blocked later during
the projector alignment
procedure.
Ceiling mount using a
DN 40 (1 1/2”-11.5 NPS)
threaded pipe.
A
F. Lift and install the projector module

G. Lift and install the Heart, as follows :
Install the mounting plate to the projection wall in the center of the markers made in step 2. The bottom of
the mounting plate should be between 6’ (15 cm) and 12’ (30 cm) above the projection.
Insert the Hearth module from top to bottom into the wall mount.
Open the Heart cover and secure the module using the two M5 bolts with a 3 mm hex screwdriver.
Install the wire cover from the center of the Heart to the ceiling.
Connect the IEC cable to the Heart power bar.
Connect the HMDI cable to the PC computer.
Connect the USB cable to the PC computer where the CAMERA logo is.
Connect the Cat5 network cable to the PC computer where the logo is.
Connect the DMX cable where the light-bulb logo is.
Gather the ve cables and secure them inside the cable cover up to the ceiling.
Close the Heart cover.
.
Page 19
02
05
09
03
06
10
04
08
07
11
Installation - Rigging
Heart module (G)
01