LUM-TEC SW200-1 User manual

1

2

3
Mission
About
Chris Wiegand - President, takes extreme pride in
every watch we produce. He is always available
to answer questions and help customers.
We take pride in our service. With service points
around the globe, you can be assured that for any
repair you will have a fast turnaround time, so you
can get your watch back on your wrist fast and
enjoy it.
LüM-TEC® takes watch manufacturing and design
to a personal level. We freely communicate with
our customers through email, phone, and on web
forums daily. We value our customer’s opinions
and input. We use customer feedback to improve
our products and our business. Our customers
are what makes LüM-TEC unique and what sepa-
rates us from other watch companies.
CONTENTS
Basic Instructions…….. 4-7
Miyota OS20…….. 8-9
Selita SW 200-1…….. 10-11
Contact…….. 12-13

4
CARE AND MAINTENANCE
A maintenance interval of between 5 and 10 years is rec-
ommended and is in addition to required battery replace-
ment on quartz models. Never open the watch yourself. If
your watch needs repair or adjustment, take or mail it di-
rectly to a LüM-TEC authorized service repair center.
NOTE: LüM-TEC assumes responsibility only for service
performed at its authorized service centers.
Shock
All LüM-TEC watches have shock-resistant
movements, individually tested to meet international
standards.

5
Dust
Dust can enter a watch if the case, crystal or
crown is not intact. A small particle is enough to stop the
movement. Have your watch repaired promptly if the
crystal becomes loose, chipped or cracked, or if there is
damage to the case or crown.
Magnetism
The exposure of a timepiece to strong magnetic fields will
affect its time-keeping and may cause it to stop. A quartz
watch should resume working with its original accuracy
when removed from the magnetic field. A mechanical
timepiece may require demagnetization before it will oper-
ate properly again.

6
Water Resistance
All LüM-TEC watches are tested to meet international standards
for water resistance.
To maintain water resistance, periodic maintenance is required.
The gaskets and crown which seal the case are subject to wear
and deterioration under normal use. These parts should be in-
spected and replaced as needed each time the watch is opened
for service, including battery changes.
CAUTION: LüM-TEC will not be responsible for any damage
caused by or related to leakage origination from improper han-
dling or damage to the case, crown, gaskets or crystal.
IMPORTANT: Do not operate the chronograph pushbutton on a
chronograph model while the time piece is under water.

7

8
SW200-1 Instructions
FUNCTION
A) SETTING THE DATE:
Unscrew the crown and pull to the 2nd position. Turn the crown clockwise to set the
proper date. Once finished, push the crown in and screw down completely.
B) SETTING THE TIME :
Unscrew the crown and pull to the 3rd position. Rotate the crown counter clockwise to
set the time. Once finished, push the crown in and screw down completely.
C) MANUAL WINDING:
Set the crown to he 1st position and rotate the crown clockwise.

9
MODELS B43/M82/83/84
Hour Hand
Second Hand
Minute Hand
1st 2nd 3rd
Screwed Down Posion
Date

10
FUNCTION
A) DATE SETTING :
To adjust the date, pull the crown to the 2nd position. Rotate the crown counter clock-
wise to the correct date. * If the date is set between the hours of 9:00 PM and 1:00 AM,
the date may not change on the following day. Once finished, push the crown in com-
pletely.
B) TIME SETTING:
Pull the crown out to the 3nd position. Turn the crown to set hour and minute hands.
When the crown is pushed back to the normal position, small second hand begins to run.
C) CHRONOGRAPH USE:
The chronograph can be started and stopped each time button “A” is pressed. Pressing
button “B” resets the chronograph and the chronograph second hand and chronograph
minute hand return to zero position.
OS20J Instructions

11
MODELS B44
Hour Hand
Chrono Minutes
Chrono Seconds
Small Second Hand
Date
Buon B
Buon A
Minute Hand
1st 2nd 3rd

12

13
CONTACT
WIEGAND CUSTOM WATCH, LLC.
7245B INDUSTRIAL PARK BLVD
MENTOR, OH 44060
T. (440)-951-1296
1-877-2lumtec
INTERNET
www.Lum-Tec.com
[e-mail]
[e-mail]
SOCIAL NETWORK
TWITTER - @LUMTECWATCHES
FACEBOOK - FACEBOOK.COM/LUMTECLLC

14