Lumisave LS-FL360-80/AC HazLoc User manual

Page | 1
Lumisave Industrial LED Technologies Ltd. www.Lumisave.com
Installation and Product Manual
For
Lumisave Industrial LED Technologies Ltd.
Model LS-FL360-80/AC HazLoc

Page | 2
THIS EQUIPMENT IS SUITABLE FOR USE IN HAZARDOUS LOCATIONS
CLASS I, DIVISION 2, GROUPS A, B, C, D, T3
WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT EQUIPMENT
UNLESS POWER HAS BEEN SWITCHED OFF OR THE AREA IS KNOWN
TO BE NON-HAZARDOUS
AVERTISSEMENT - RISQUE D'EXPLOSION - AVANT DE DECONNECTER
'EQUIPEMENT, COUPER LE COURANT OU S'ASSURER QUE
L'EMPLACEMENT EST DESIGNE NON DANGEREUX
Safety & Installation Instructions
PLEASE READ AND FOLLOW ALL SAFETY INSTRUCTIONS
BEFORE INSTALLING THIS FIXTURE
1. This fixture should be installed in strict accordance with the National
Electrical Code and any local requirements.
2. This fixture should be mounted in locations and at heights where it will
not readily be subjected to tampering by unauthorized personnel.
3. Do not let power supply cords touch hot surfaces.
4. Do not use this equipment for other than intended use.
5. Installation and servicing of this fixture should be performed by
qualified personnel.
6. Please note that Hi-Power LED’s are very bright; please do not look
directly at LED.
7. Only install the Fixture using the included bracket as this was specifically
designed for this purpose.
8. Hi powered LED’s do not get very hot but too much heat can reduce
their rated life, so with this in mind, please ensure that adequate
spacing is provided from heaters, etc and that air can freely flow around
the light.
9. Ensure that the light is securely fastened to its mounting surface. Please
see the Installation page for mounting instructions.
SAVE THESE INSTRUCTIONS

Page | 3
Installation
The LS-FL360-80/AC HazLoc is easy to mount. You can either remove the
bracket from the fixture and install the bracket first if sufficient clearance
for installation is required or you can leave it attached an install if the
location and tools allow for proper clearance.
For fixing to a wood surface we recommend two 3/8” Dia. lag bolts at least
2 Inches long (or a single 1/2 X 3” long) or conversely two 3/8”Dia. grade 5
bolts (or a single ½” inch) to affix the light to a metal structure.
Re-install fixture to bracket (If removed) and tighten the angle adjustment
(Pivot) bolts to lock the fixture in the desired angle.
Note: Install the Light high enough that it will be out of the line of sight.
Usage & Maintenance
The LS-FL360-80/AC HazLoc is suitable for wet locations and may be used
either inside or outside. It is designed to accept working AC voltages of
85V to 265V at 50 to 60 Hz frequency so it may be used in either a 120V or
240V application with excellent resistance to power fluctuations.
IMPORTANT: The only maintenance required is to keep the cooling surface
(Aluminum Fins) free of dust or dirt buildup. Failure to blow down or
vacuum excessive buildup will reduce the rated life of the fixture. Please do
not use high pressure water spray on the fixture as it may damage the
seals.

Page | 4
Specifications
Hazardous Location Rating: Class 1, Division 2, Groups A,B,C,D, T3
Temperature Rating: -40°C Tamb ≤ 40°C
AC Power: 85V to 265V Frequency: 50 to 60Hz.
Current: .695A Multi-Chip Output: 6400Lm
Power: 80W Power Factor: .95%
Chip Efficiency: 80Lm/Watt Rated Life: +75,000Hrs
Warranty
All Lumisave Multi-Chip Products carry a 5 year Limited Warranty.
Note: Misuse of fixture will void Warranty, for Warranty details or
Service and Support please see www.Lumisave.com.
Mailing and contact information:
Lumisave Industrial LED Technologies Ltd.
1643 Ogilvie St.
Prince George, BC
V2N 1W7, Canada
Tel: [phone]