Luna APF161 User manual

Instruction Manual
5 6
7. Remove the 4 screws located on the
front of the motor unit. Place the rear grille
into position on the motor unit (handle up),
then secure into position with the 4 screws
provided.
Rear Grille
Grille
Screws
8. Remove plastic sleeve from motor shaft,
then place the fan blade on the motor shaft,
aligning the flat on the shaft with the fan blade
screw. Securely tighten the fan blade screw.
Fan Blade
Fan Blade
Screw
9. After loosening, remove the fixing screw and nut
from the bottom of the front grille. Place the front
grille over the rear grille, press grille retaining clips
into position, then tighten grille fixing nut and screw.
Ensure that the fan blade is entirely enclosed and the
complete grille is securely in position.
Front
Grille
Grille
Retaining
Clips (4)
Grille Fixing
Screw & Nut
OPERATION
Make sure that you read all of the safety
warnings before you operate this unit for the
first time. Plug the unit to a standard mains
socket and turn on the mains switch.
Off / Speed Switch
1. Turn the rotary switch on the top of the
motor unit to select between fan speeds:
0 (OFF ),1, 2 or 3.
0= Off
1= Low Speed
2= Medium Speed
3= High Speed
Off/Speed
Switch
Oscillation Control
2. Push the oscillation knob downward to allow
the motor unit to oscillate horizontally through
approximately 80° angle. Lift oscillation knob
upward to turn off oscillation mode.C
Oscillation
Knob
Off
On
Vertical Direction of Motor Unit
3. The vertical direction of the motor
unit can be adjusted by loosening the tilt
adjustment knob, tilting the complete head
unit (incorporating motor unit and assembled
grille) forward or back ward until the desired
direction is reached, then tightening the tilt
adjustment knob. Important! Please read these instructions carefully
Model APF161
Arlec guarantees this produc t in accordance with the Aus tralian Consumer L aw.
Arlec also warrant s to the original first purchaser of this product (“you”) from a retailer that this product w ill be free of defect s in
materials and workmanship for a period of 12 months from the date of purchase; provided the product is not used other than for the
purpose, or in a manner no t with in the scop e of the recommendat ions and limitat ions, specif ied by Ar lec, is new and not damaged at the
time of purchase, has no t been subjected to abuse, misuse, neglect or damage, has not been modified or repaired w ithout the approval
of Arlec and has not been used for commercial purposes (“Warrant y”).
If you wish to claim on the Warrant y, you must, at your own expense, return the product, and provide proof of original purchase and
your name, address and telephone number, to Arlec at the address below or the ret ailer from whom you originally purchased the
product within 12 months from the date of purchase.
Arlec wi ll (or aut horise t he retailer t o) assess any claim you may make o n the Warrant y in the above man ner and if, i n Arlec’s reaso nable
opinion, the Warranty applies, Arlec will at it s own option and expense (or authorise the retailer to) replace the product with the same
or similar product or repair t he product and return it to you or ref und the pr ice you paid for the pro duct. A rlec wil l bear its o wn expenses
of doing those things, and you must bear any other expenses of claiming on the Warranty.
The Warranty is in addition to other rights and remedies you may have under a law in relat ion to the product to w hich t he Warranty
relates.
Our goods come with guarantees that cannot be excluded under t he Australian Consumer Law. You are entitled to a replacement or
refund for a major failure and for compensat ion for any other reasonably foreseeable loss or damage. You are also entitled to have the
goods repaired or replaced if the goods fail to be of accep table qualit y and t he failure does not amount to a major failure.
Arlec Australia Pty. Ltd. ACN 009 322 105 (“Arlec”) gives the Warranty.
Arlec’s telephone number, address and email address are:
Customer Service: [phone]
New Zealand Toll Free: 0800 003 329
Building 3, 31 – 41 Joseph Street, Blackburn North, Victoria, 3130
Blackburn North LPO, P.O. Box 1065, Blackburn North, 3130
Email: [email protected] CPIN002920
CPIN002920
Stainless Steel
Pedestal
Fa n 40cm
L
una
Tilt
Adjustment
Knob
Height Adjustment
4. The fan height can be adjusted by loosening
the height adjustment knob, lifting the inner
pole (with attached motor unit) and then
tightening the height adjustment knob when
the desired height is obtained.
Height
Adjustment
Knob
CARE & MAINTENANCE
1. Always disconnect the cord from
the electrical outlet when cleaning your fan.
2. Light accumulated dust may be removed from
the fan with a soft cloth or vacuum cleaner us-
ing the dusting brush attachment.
3. Wipe the exterior surfaces of the fan
occasionally with a cloth moistened
(not dripping wet) with a mild soap solution.
Dry the case thoroughly with a soft dry cloth
before operating the fan.
4. Avoid the use of gasoline, benzine, thinner
etc as they may result in damage to the fan.
5. Store the fan in a clean dry place when not
in use.
Warning: Do not immerse the fan in water or
allow water to drip into the interior of the fan
housing as this could create a fire or electric
shock hazard.

3 42
ASSEMBLY
1. Remove all the sub assemblies from the box.
2. Unfasten the base fixing knob and
retaining washer.
3. Place the base weight and retaining washer
over the threaded stud of the main body
Base
Fixing
Knob
Retaining
Washer
Base
Weight
Base Fixing
Knob
Retaining
Washer
4. Fasten the fixing knob firmly to fix
in position.
Secure with
Base Fixing
Knob
The assembly of the fan base with main body
has been completed.
OFF BUTTON
MODE BUTT
5. Remove neck fixing bolt and knob from top of
inner pole.
Neck
Fixing Knob
Fixing
Bolt
6.Remove tilt adjustment knob from neck of
motor unit, then place neck over inner pole, with
locating screw aligning with slot in side of pole.
Locating
Screw
Slot
7. a) Place bolt through neck and inner pole.
b) Tighten locating screw leaving approx.
3mm gap under screw head.
c) Neck fixing knob to bolt.
d) Fit tilt adjustment knob into neck.
Locating
Screw
Fixing
Bolt
Neck
Fixing Knob
Tilt
Adjustment
Knob
3mm
Now you can adjust the tilt of the motor unit
and secure in position by tightening the tilt
adjustment knob.
IDENTIFICATION
1. Main Body
2. Base Plate
3. Inner Pole
4. Off/Speed Switch
5. Height Adjustment Knob
6. Front Grille
7. Fan Blade
8. Rear Grille
9. Carry Handle
10. Motor Unit
11. Oscillation Control
CPIN002920
ASSEMBLY DIAGRAM
1. Base Fixing Knob
2. Base Fixing Washer
3. Base Weight
4. Base Plate
5. Main Body
6. Rear Grille Screws
7. Grille Fixing Screw and Nut
8. Fan Blade Screw
9. Neck of Motor Unit
10. Locating Screw
11. Neck Fixing Knob
12. Neck Fixing Bolt
13. Tilt Adjustment Knob
1.
4.11.10.
3.
6.
7.
8.
10.
9.
5.
2.
SAFETY INSTRUCTIONS
• READ all these instructions carefully
and store in a safe place for future
reference.
• This appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning
use of the appliance by a person
responsible for their safety. Children
should be supervised to ensure that
they do not play with the appliance.
•If the supply cord is damaged, it must
be replaced by the manufacturer, its
service agent or similarly qualified
persons in order to avoid a hazard.
• DONOT use this unit for functions other
than those described in this instruction
manual
• DONOT tilt the unit. Always keep in
upright. Position on a flat and stable
surface, where it cannot be easily
knocked over. Take extra care when
operating
• DONOT connect the unit unless it
completely assembled.
• DONOT use the unit in a wet room,
such as a bathroom or laundry
• DONOT touch the unit with wet hands
or bare feet
• DONOT use the unit in the presence of
inflammable substances or vapor such
as alcohol, insecticides, petrol etc.
• DONOT use the mains plug to start and
stop the unit
• DONOT pull the supply cord or place it
near a heat source. Always unwind the
cord completely to avoid overheating.
• DONOTinsert or allow foreign objects
to enter the grille openings as this may
cause damage to the appliance and/or
user.
• DONOT allow children to play with this
appliance. This appliance is not intended
for use by children or infirm persons
without supervision.
• DONOT conduct repairs on this unit.
It has been built in accordance with
relevant safety and performance
standards. An electrical specialist must
carry out all repairs.
•This unit is intended for indoor use only.
• ALWAYS unplug the unit from the mains
before maintenance or cleaning
•ALWAYSEnsure that the fan is switched
off from the supply mains before
removing the guard.
• ALWAYSuse the switch on the control
panel to start and stop the unit
• ALWAYS keep a clearance of at least
200mm from walls furniture and curtains
• ALWAYS turn off and unplug the unit
when not in use
ENERGY SAVING TIPS
• Donotlocatethefanwherefurnitureor
other objects can obstruct the air flow.
• Keepblinds/curtainsclosedduringthe
sunniest part of the day
• Closethefireplacedamper,floorand/
or wall registers, so cool air does not
escape through the chimney or duct
work
SPECIFICATIONS
Model APF161
Voltage 220-240V a.c.
Frequency 50Hz
Power 50W
1.
3.
4.
2.
5.
6. 7.
7.
8.
8.
9.
13.
10.
11.
12.