Lynxspring KANEsys JENE-PCLCD-R User manual

JENE-PCLCD-R Installation Guide

Revised 2/24/2011 Page i
Copyright © Lynxspring, Inc. 1210 NE Windsor Drive, Lee’s Summit, MO 64086 877-649-5969
Trademarks
JENEsys and the JENEsys logo are U.S. trademarks of Lynxspring, Inc.
Lynxspring and the Lynxspring logo are U.S. registered trademarks of Lynxspring, Inc.
Other brands and product names mentioned in this manual may be trademarks or registered
trademarks of their respective companies and are hereby acknowledged.
Copyright Notice
Copyright © 2010, Lynxspring, Inc.
All rights reserved.
This document contains proprietary information which is protected by copyright. No part of this
document may be copied, photocopied, reproduced, translated, or converted to any electronic
or machine-readable form in whole or in part without prior written approval of Lynxspring, Inc.
Disclaimer
NO WARRANTY. This technical documentation is being delivered to you AS-IS, and
Lynxspring makes no warranty as to its accuracy or use. Any use of the technical
documentation or the information contained therein is at the risk of the user. Documentation
may include technical or other inaccuracies or typographical errors. Lynxspring reserves the
right to make changes in this document without prior notice, and the reader should in all cases
consult Lynxspring to determine whether any such changes have been made. The information
in this publication does not represent a commitment on the part of Lynxspring.
Lynxspring shall not be liable for incidental or consequential damages resulting from the
furnishing, performance, or use of this material.
This guide may contain links and references to third-party websites that are not under the
control of Lynxspring, and Lynxspring is not responsible for the content of any reference
material or linked websites. If you access a third party website mentioned in this guide, then
you do so at your own risk. Lynxspring provides these links only as a convenience, and the
inclusion of the link does not imply that Lynxspring endorses or accepts any responsibility for
the content on those third-party sites.
Lynxspring, Inc.
1210 NE Windsor Drive
Lee’s Summit, MO 64086
http://www.lynxspring.com

Revised 2/24/2011 Page ii
Copyright © Lynxspring, Inc. 1210 NE Windsor Drive, Lee’s Summit, MO 64086 877-649-5969
Table of Contents
OVERVIEW ................................................................................................................................................................3
PRECAUTIONS..........................................................................................................................................................4
1. LCD APPLICATIONS AND KIT REVIEW ........................................................................................................5
2. INSTALLING THE COMMUNICATION OPTION CARD..............................................................................8
3. INSTALLING THE SHROUD.............................................................................................................................10
4. MOUNTING THE TRIM RING..........................................................................................................................11
5. MOUNTING THE LCD ON DIN RAIL .............................................................................................................13
6. MOUNTING WITH LCD EYELETS .................................................................................................................14
7. POWER OPTIONS...............................................................................................................................................15
8 UN-INSTALLING THE JENE-PCLCD-R .........................................................................................................17
9. LISTING OF KIT AND REPLACEMENT PARTS ..........................................................................................18
10. TECHNICAL DATA...........................................................................................................................................20
11. RETURNING A DEFECTIVE UNIT................................................................................................................21
12. CERTIFICATIONS ............................................................................................................................................22
Federal Communications Commission (FCC)........................................................................22
RoHS CompliantDeclaration of Conformity............................................................................22
Declaration of Conformity......................................................................................................23

JENE-PCLCD-R Installation Guide
©2010 Lynxspring. All rights reserved. Page 3
Overview
This document covers the mounting and wiring of the JENE-
PCLCD-R remote LCD operator’s panel and its accessories. It
assumes that you are an engineer, technician, or service person
who is performing control system installation with an embedded
NiagaraAX JENE and/or JACE controller. Instructions in this
document apply to the following products:
Models Description
JENE-PC-LCD-R Remote LCD operator’s panel
JENE-PC-LCDCARD
30 pin communication option card
LCD-S Shroud adaptor to JENE/JACE controller
LCD-TR Trim ring mounting for remote applications
LCD-R-RS485 RS-485 converter for long distance remote
applications
Not covered in this document is the Niagara
AX
software and LCD configuration
required for a fully functioning unit. Refer to the JENEsys® PC Series LCD-R
Operators Panel Manual for this information.
These are the main topics included in this document:
1. LCD Application and Kit Review , page 5
2. Installing the Communication Option Card, page 8
3. Installing the Shroud, page 10
4. Mounting the Trim Ring, page 11
5. Mounting the LCD on DIN Rail, page 12
6. Mounting with LCD Eyelets, page 13
7. Power Options, page 14
8. Un-Installing the JENE-PCLCD-R, page 16
9. Listing of Kit and Replacement Parts, page 17
10. Technical Data, page 19
11. Returning a Defective Unit, page 20
12. Certifications, 21
Information and specifications published here are current as of the dateof publication of this document. Lynxspring reserves
the right to change or modifyspecifications without prior notice. The latest product specifications can be found by
contacting our corporate headquarters or accessing www.lynxspring.com. Products or features contained herein may be
covered by one or more U.S. or foreign patents.

JENE-PCLCD-R Installation Guide
©2010 Lynxspring. All rights reserved. Page 4
Precautions
This document uses the following warning and caution conventions:
Cautions remind the reader to be careful. They alert readers to situations where
there is a chance that the reader might perform an action that cannot be undone,
might receive unexpected results, or might lose data. Cautions contain an
explanation of why the action is potentially problematic.
Warnings alert the reader to proceed with extreme care. They alert readers to
situations where there is a chance that the reader might do something that
can result in personal injury or equipment damage. Warnings contain an
explanation of why the action is potentially dangerous.
Safety Precautions
The following items are warnings of a general nature relating to the installation and
start-up of the JENE controller. Be sure to heed these warnings to prevent personal
injury or equipment damage.
•
Depending on power module used, the circuit powering the JENE is 24Vac
at 50/60 Hz (if using JENE-PC-PWR-UN), 120 Vac at 50/60 Hz (if using
JENE-PC-WWPM-120). Disconnect power before installation or servicing
to prevent electrical shock or equipment damage.
• Make all connections in accordance with national and local
electrical codes. Use copper conductors only.
•To reduce the risk of fire or electrical shock, install in a controlled
environment relatively free of contaminants.
•This device is only intended for use as a monitoring and control device.
To prevent data loss or equipment damage, do not use it for any other
purpose.
Static Discharge Precautions
Static charges produce voltages high enough to damage electronic components. The
microprocessors and associated circuitry within a JENE controller are sensitive to static
discharge. Follow these precautions when installing, servicing, or operating the system:
•Work in a static-free area.
•Discharge any static electricity you may have accumulated. Discharge
static electricity by touching a known, securely grounded object.
•
Do not handle the printed circuit board (PCB) without proper protection
against static discharge. Use a wrist strap when handling PCBs. The wrist
strap clamp must be secured to earth ground.

JENE-PCLCD-R Installation Guide
©2010 Lynxspring. All rights reserved. Page 5
1. LCD Applications and Kit Review
The JENE-PCLCD-R is intended to be used for multiple applications. Each application
however requires an interface to JENEsys PC 1000/6000 or equivalent JACE 2/6
controller. For each application Lynxspring has designed a kit with a comprehensive list of
materials to successfully install the JENE-PCLCD-R.
Applications
•Controller Mounted (kit part no. JENE-PCLCD-R-Unit)
•Remote Mounting >50ft up to 4,000 ft from the controller (kit part no. JENE-PCLCD-
R-Remote)
•Locally Mounted up to 50ft from the controller (kit part no. JENE-PCLCD-R-Local)
•Hand Held or Service Tool (kit part no. JENE-PCLCD-R-Service)
•RS-485 Convertor to extend mounting beyond 50ft from the controller (kit part no.
LCD-R-RS485; included with JENE-PCLCD-R-Remote)
Kits
•JENE-PCLCD-R-Unit; is intended to mount the LCD on the JENE/JACE controller; it
includes –
1. LCD Interface (JENE-PCLCD-R; qty 1)
2. LCD Communication option card (JENE-PC-LCDCARD; qty 1)
3. Shroud for mounting onto the base of the JENE/JACE controller (LCD-R-S; qty 1)
•JENE-PCLCD-R-Remote; is used to mount the LCD interface remotely from the
JENE/JACE controller greater then 50ft and up to 4,000 ft; it includes -
1. LCD Interface (JENE-PCLCD-R; qty 1)
2. RS-485 converter kit (LCD-R-RS485; qty 1)
3. Trim ring for mounting on a panel (LCD-R-TR; qty 1)
4. Power supply with 2.1mm barrel connection to RS-485 converter kit (JENE-PC-
WWPM-120; qty 1)
•JENE-PCLCD-R-Local; used to mount the LCD within 50ft of the JENE/JACE
controller; it includes –
1. LCD Interface (JENE-PCLCD-R; qty 1)
2. Trim ring for mounting on a panel (LCD-R-TR; qty 1)
3. LCD Communication option card (JENE-PC-LCDCARD; qty 1)
4. 50ft flat satin cable with RJ11 connectors (8101-64150; qty 1)
•JENE-PCLCD-R-Service; is intended to be used as a Hand Held or Service Tool; it
includes –
1. LCD Interface (JENE-PCLCD-R; qty 1)
2. LCD Communication option card (JENE-PC-LCDCARD; qty 1)
3. Power supply with 2.1mm barrel connection to RS-485 converter kit (JENE-PC-
WWPM-120; qty 1)
4. RJ11 to 9pin Female RS-232 adaptor when connecting to the on-board
JENE/JACE controller RS-232 port (9-MA09F11; qty 1)
5. Six foot coiled cable (TEL-6000-06K-RJ11; qty 1)

JENE-PCLCD-R Installation Guide
©2010 Lynxspring. All rights reserved. Page 6
6. 25 foot coiled cable (TEL-6000-25K-RJ11; qty 1)
•LCD-R-RS485; is a kit that includes everything needed to power and convert an RS-
485 signal when the LCD is mounted greater than 50ft from the JENE /JACE
controller; it includes -
1. RJ11 to 9pin male RS-232 adaptor connected to the 9-pin RS-232 port of the
RS-485/RS-232 converter (9-MA09M11; qty 1)
2. RS-485/RS-232 converter (485SD9TB; qty 1)
3. One foot flat satin cable (8101-64101; qty 1)
Communication Ports
JENE bottom side (cover removed)
Figure 1
Serial Ports
There are two serial ports on the JENE base unit. Each has a UART capable of operation up to
115,200 Baud. At the bottom of the board (see Figure 1), the left port is an RS-232 port using a DB-
9 plug (male) connector. To the right of this is a two-wire with shield, isolated RS-485 port, using a
screw-terminal connector plug.
A green “rece
ive” LED and yellow “transmit” LED are provided for each serial port. These
LEDs are located on the bottom board, on the opposite side of the serial connectors.
These LEDs are labeled on the board (COM 1, COM2) and are not visible with the cover
on.
RS-232—An RS-232 serial port using a male DB-9 connector always operates as COM1. You
can use standard DB-9 serial cables with this port. The JENE is a serial DTE device; such another
DTE device (PC, for example) requires a “null modem” cable. If connecting the JENE to a DCE
device (modem, for example), a reverse cable is used. Table 1 provides standard serial DB-9
pinouts.
If a modem option card (JENE-PC-MODEMCARD) is installed, this port becomes
disabled—except if rebooted with the mode jumper in the “Serial Shell” position.

JENE-PCLCD-R Installation Guide
©2010 Lynxspring. All rights reserved. Page 7
Table 1 Serial port (RS-232 and RS-485) pinouts.
RS-485— An RS-485, optically isolated port uses a 3-position, screw terminal connector and
always operates as COM2. Wire to this connector with shielded 18-22AWG wiring (refer to the
TIA/EIA-485 standard). The screw terminals (from left-to-right) are shield, plus (+), and minus (–).
LEDs
LEDs for the two serial ports are located on the JENE’s bottom board, on the opposite
side of the RS-232 and RS-485 ports (see figure 2 on page 8). Labels “COM1” and
“COM2” correspond to the software configuration of the COM ports. LEDs show the
transmit and receive information for the serial ports and optional modem.
Note: You must remove the cover to the serial port LEDs.
•The yellow transmit LED indicates that the JENE is sending data out
the serial port over a communications line to a connected device.
•The green receive LED indicates that the JENE is receiving data from a connected
device.
These LEDs provide a fixed on-time when data is detected on the port. If the receive LED
is on constantly, this indicates a problem with the communications channel, such as a
shorted wire or reversed wiring.

JENE-PCLCD-R Installation Guide
©2010 Lynxspring. All rights reserved. Page 8
2. Installing the Communication Option Card
A 30 pin serial communication option card (part # JENE-PC-LCDCARD, includes a data cable to
the LCD), provides communication and power from the JENE/JACE controller to the LCD. The
maximum distance allowed to power the LCD using the communication option card is limited to
50ft.
Typical applications that use this card include; Controller Mounted (kit part no. JENE-
PCLCD-R-Unit), locally Mounted up to 50ft from the controller (kit part no. JENE-
PCLCD-R-Local) and the Hand Held or Service Tool (kit part no. JENE-PCLCD-R-
Service)
Installation Instructions
Step 1 Remove power from the JENE/JACE controller. Power to the JENE/JACE controller
must be OFF when installing or removing the JENE-PC-LCDCARD cards or damage
may occur. Also, you must be very careful to plug any JENE-PC-LCDCARD card into
its connector properly (pins aligned).
Step 2 Remove the JENE/JACE controller cover. To do this, select and press in the four tabs
on both ends of the unit and lift the cover off. Retain the cover in case the JENE-PC-
LCDCARD Housing Cover must be removed at a later date.
Step 3 Remove the battery and bracket assembly by taking out the four screws holding it in
place, setting the screws aside for later. Unplug the battery from the connector on the
JENE/JACE controller. See Figure 1 below.
Figure 1
Step 4 Remove the blanking end plate for the slot into which you are installing the JENE-PC-
LCDCARD card. Retain the blanking end plate in case the JENE-PC-LCDCARD card
must be removed at a later date.
Note: No longer does the optional communication card block one of the serial ports (RS-232
or RS-485) on the controller.
Step 5 Carefully insert the pins of the JENE-PC-LCDCARD card into the socket of the
appropriate option slot. The mounting holes on the option board should line up with the
standoffs on the base board. If they do not, the connector is not properly aligned.
Press until the JENE-PC-LCDCARD card is completely seated. If you encounter any
resistance, check that the pins are aligned properly.

JENE-PCLCD-R Installation Guide
©2010 Lynxspring. All rights reserved. Page 9
Note: If there is already a card in Option Slot 1, install the JENE-PC-LCDCARD card into
Option Slot 2 and when setting up the Serial LCD network, change the Comm Address
to “COM2”.
Step 6 Connect the data cable to the JENE-PC-LCDCARD card via one of the two RJ11
connectors.
Step 7 Place the custom end plate that came with the JENE-PC-LCDCARD card over its
connector. See Figure 2 below.
Figure 2
Step 8 Plug the battery cable into the battery connector on the JENE/JACE controller. Please
refer back to Figure 2 for location.
Step 9 Set the battery and bracket assembly back over the card slot, with the mounting holes
aligned with the standoffs. The cable should be between the end plate (if mounting
onto the controller with a shroud) and the edge of the battery (between the standoffs).
Step 10 Place the four screws through the battery bracket, end plates and into the standoffs on
the JENE/JACE controller. Hand tighten the screws. See Figure 3 below.
Figure 3
Step 11 If accessory modules were unplugged, plug them back into the JENE/JACE controller
as before and secure.