MADV MIJIA 360 Camera Installation instructions

MIJIA 360 Camera
LET’S GET STARTED
Complete user manual available at www.madv360.com/product.html

1
Product overview
Package contents: MIJIA 360 Camera, Camera Selfie Stick, USB Cable, Tripod, Protection
Bag, Mounting Adapter, User Manual.

2
Your Camera
Selfie Stick Lock
Control Contacts
Tripod Thread
Shutter Button
Wi-Fi Button
Power/Mode Button
Mic
MicroSD Card Slot & MicroUSB Port

3
Instructions
1. Power your camera on/off
Power on: Short-press the power/mode button. The video and photo indicators will light up
together. When the front mode light is illuminated, the camera has been powered on.
Power off: Long-press the power/mode button. When the front mode light is no longer
illuminated, the camera has been powered off.
2. Switch camera modes
Once the camera is powered on, you can switch between video and photo mode by
short-pressing the power/mode button (the default mode is video mode).
3. Video mode
In video mode the video indicator is illuminated orange. To begin filming short-press the
shutter/confirm button. During filming, the video indicator will flash red.
To stop filming, short-press the shutter/confirm button. When the camera stops filming, the
camera indicator will quickly flash three times. The camera indicator will then stop flashing
and be illuminated orange.
4. Photo mode
In photo mode the photo indicator is illuminated orange. To take a photo, short-press the
shutter/confirm button. When you take a photo, the photo indicator light will flash once.
5. Camera battery indicator
a. When not connected to the charger
When the battery is below the warning level: The battery indicator flashes red slowly.
When the battery is above the warning level: The battery indicator is turned off.
b. When connected to the charger
When charging: The battery indicator is illuminated red.
When charging is complete: The battery indicator is illuminated orange.
6. Standby mode
If no button is pressed on the camera for 120 seconds, the camera will enter standby mode.
The battery indicator will flash orange. Press any button to wake up the camera.

4
7. Reset the camera Wi-Fi password
Long-press the Wi-Fi button for 5 seconds to reset the Wi-Fi password to the default
password (12345678).
8. Update camera firmware
You can update your camera firmware using the MIJIA 360 app. Check your phone is
connected to the Internet and open the MIJIA 360 app. Once your phone has connected to
the camera, you will automatically receive notifications if there is a new update available.

5
Specs
Product name: MIJIA 360 Camera
Model: QJXJ01FJ
Dimensions: 78.00×67.40×24.03mm
Weight: 108.3g Focal length: 1.43
Input: 5V 2A Aperture: f/2.0
Battery capacity: 1600mAh Protection: IP67
Standby power consumption: 3.8W
Storage temperature: -20–45°C
Storage humidity: 10%–90%
Image resolution: up to 6912×3456
Video resolution: up to 3840×1920
Wireless connectivity: Wi-Fi IEEE 802.11b/g/n 2.4GHz, Bluetooth 4.0
Expandable storage options: microSD card (up to 128GB, at least Class 10). Use U3 microSD
cards for recording video at the highest resolution.
System requirements: Android 5.0/iOS 9 or later
Recommended adapter specifications
Input: 100-240~50/60Hz
Output: 5V 2A /9V 2A /12V 1.5A
Supported standards: QC2.0

6
Your selfie stick
Selfie Stick
Lock Control Contacts
Control Button
Selfie stick usage instructions
1. Connect the selfie stick with the MIJIA 360
camera (Note: The control contacts at the
top of the selfie stick should touch the
control contacts at the bottom of the
camera).
2. Short-press the control button on the selfie
stick to turn on the camera.
3. When the camera is turned on, long-press
the control button on the selfie stick to
change between photo mode and video
mode.
4. When the camera is in photo mode,
short-press the control button on the selfie
stick to take a photo.
5. When the camera is in video mode, short
press the control button on the selfie stick to
start filming. Short-press the control button
on the selfie stick again to stop filming.

7
Scan the QR code to
download and install
Download and install the MIJIA 360 app to your device
Connect your camera to the MIJIA 360 app
Search for “MIJIA 360” in the Google Play app store, or scan the QR code below to
download the MIJIA 360 app.
1. Download and install the MIJIA 360 app.
2. Short-press the camera Wi-Fi button to enable the camera Wi-Fi. When the camera Wi-Fi is
enabled the camera Wi-Fi will flash blue.
3. Open the MIJIA 360 app. Touch the connect button. Follow the instructions to connect the
MIJIA 360 app to the camera. Once the connection is complete the Wi-Fi button will be
illuminated blue.
4. Default camera password: 12345678.

8
1. The camera may lower its performance or shut down automatically while being used in
extreme weather conditions.
2. Do not use the camera when air temperature or humidity are changing drastically;
otherwise, condensate may appear inside the camera. If this happens, open the MicroUSB
port cover to allow evaporation.
3. Do not place the camera face-down on rough surfaces directly to avoid scratching the lens.
4. Please don’t use the camera in a confined environment with a temperature higher than 35
degrees celsius.
5. The MIJIA 360 Camera passed our controlled lab tests which showed that it meets the IP67
standard. This means that MIJIA 360 Camera is protected from dust and the effects of
immersion in water to a depth of up to 1 meter for 30 minutes.
However, the camera’s dust-, water-, and splash-resistance capabilities are not permanent
and will decrease over the camera's lifetime.
Camera care and maintenance

9
Function
Wi-Fi
Bluetooth
Frequency
2412-2472 Mhz
2402-2480 Mhz
Maximum Out Power(EIRP)
17.64 dBm
5.72 dBm
When using electrical appliances, basic safety precautions should always be followed
including the following:
1. Read all instructions.
2. To protect against unexpected damage do not immerse the appliances in water or other
liquids.
3. Close supervision is necessary when any appliance is used by or near children.
4. Disconnect the charger from the socket when not in use. Failing to do so may result in a fire
or other safety hazards.
5. Do not place on or near a hot gas or electric burner, or in a heated oven.
6. Do not use appliance for anything other than the intended use.
Important safeguards
RED RF Output table

10
Notices for Customers in the U.S.A.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause
undesired operation.
The Federal Communications Commission warns that changes or modifications of the unit not
expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
RF Exposure Information and Statement
The SAR limit for the USA (FCC) is 1.6 W/kg averaged over one gram of tissue. The
QJXJ01FJ device (FCC ID: 2AJ2LQJXJ01FJ) has been tested against this SAR limit. The
highest SAR value reported during product certification for use at the ear is 0.226 W/kg and
when properly worn on the body is 0.031 W/kg.
WARNING: This product can expose you to chemicals including Pb, which is known to the
State of California to cause cancer, and Pb, which is known to the State of California to cause
birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.

11
IC Statement
English: This device complies with Industry Canada's license-exempt RSS standard. Operation
is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference, including interference that may cause undesired
operation of the device.
French: Le present appareil est conforme aux CNR d'Industrie Canada applicables iaux
appareils radio exempts de licence. L'exploitation est autorisee aux deux deux conditions
suivantes:
l'appareil ne doit pas produire de brouillage.
l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le
brouillage est susceptible d'en compromettre le fonctionnement.
Notices for Customers in Canada

12
EU Declaration of Conformity
We, Beijing MADV Technology Co., Ltd., declare under our sole responsibility that the MIJIA
360 Camera, model number QJXJ01FJ, is in conformity with the essential requirements and
other relevant provisions of the Radio Equipment Directive (RED) 2014/53/EU. The full
declaration of conformity may be consulted at www.madv360.com
RF Exposure Information and Statement
A minimum separation distance of 0.5 m must be maintained between the user’s body and the
device, including the antenna during body-worn operation to comply with the RF exposure
requirements in Europe. The SAR limit for mobile devices is 2.0 W/kg and the highest SAR
value recorded for this device when tested for use at the body was 0.268 W/kg.
Notices for Customers in Europe
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED
WITH AN INCORRECT BATTERY TYPE
DISPOSE OF USED BATTERIES ACCORDING
TO LOCAL LAWS AND REGULATIONS

Powered by: Beijing MADV Technology Co., Ltd.
See more at madv360.com
Made in China
SAVE THESE INSTRUCTIONS

MIJIA 360 Kamera
ERSTE SCHRITTE
Vollständiges Handbuch unter www.madv360.com/product.html

1
Produktübersicht
Paketinhalt: MIJIA 360 Kamera, Kamera-Selfie-Stick, USB-Kabel, Stativ, Schutztasche,
Montageadapter, Benutzerhandbuch.

2
Kamera
Selfie-Stick-Anschluss
Steuerkontakte
Stativgewinde
Auslöser
WLAN-Taste
Power-/Modustaste
Mikrofon
microSD-Kartensteckplatz und microUSB-Port

3
Anweisungen
1. Ein-/Ausschalten der Kamera
Einschalten: Drücken Sie kurz auf die Power-/Modustaste. Video- und Fotoanzeige leuchten
zusammen auf. Wenn das vordere Moduslicht leuchtet, ist die Kamera eingeschaltet.
Ausschalten: Drücken Sie länger auf die Power-/Modustaste. Wenn das vordere Moduslicht
nicht länger leuchtet, ist die Kamera ausgeschaltet.
2. Wechseln zwischen Kameramodi
Nach dem Einschalten der Kamera können Sie zwischen dem Video- und dem Fotomodus
wechseln, indem Sie kurz auf die Power-/Modustaste drücken. (Standardmäßig ist der
Videomodus aktiviert.)
3. Videomodus
Im Videomodus leuchtet die Videoanzeige orange. Um zu filmen, drücken Sie kurz auf den
Auslöser/die Bestätigungstaste. Beim Filmen leuchtet die Videoanzeige rot.
Um die Filmaufnahme zu beenden, drücken Sie kurz auf den Auslöser/die
Bestätigungstaste. Wenn nicht mehr mit der Kamera gefilmt wird, blinkt die Kameraanzeige
dreimal kurz auf. Anschließend leuchtet die Kameraanzeige orange.
4. Fotomodus
Im Fotomodus leuchtet die Fotoanzeige orange. Um zu fotografieren, drücken Sie kurz auf
den Auslöser/die Bestätigungstaste. Beim Fotografieren blinkt die Fotoanzeige einmal auf.
5. Akkuanzeige der Kamera
a. Ohne Verbindung zum Ladegerät
Akku unterhalb der Warnschwelle: Die Akkuanzeige blinkt langsam rot.
Akku oberhalb der Warnschwelle: Die Akkuanzeige ist ausgeschaltet.
b. Bei Verbindung zum Ladegerät
Beim Laden: Die Akkuanzeige leuchtet rot.
Bei abgeschlossenem Ladevorgang: Die Akkuanzeige leuchtet orange.
6. Standby-Modus
Wenn 120 Sekunden lang keine Taste betätigt wird, wechselt die Kamera in den
Standby-Modus. Die Akkuanzeige blinkt orange. Drücken Sie auf eine beliebige Taste, um
die Kamera zu aktivieren.

4
7. Zurücksetzen des WLAN-Passworts
Drücken Sie länger als 5 Sekunden auf die WLAN-Taste, um das WLAN-Passwort auf den
Standardwert (12345678) zurückzusetzen.
8. Aktualisieren der Kamerafirmware
Sie können die Kamerafirmware über die App MIJIA 360 aktualisieren. Vergewissern Sie
sich, dass Ihr Telefon mit dem Internet verbunden ist, und öffnen Sie die App MIJIA 360.
Sobald sich Ihr Telefon mit der Kamera verbunden hat, werden Sie automatisch über neue
verfügbare Aktualisierungen benachrichtigt.

5
Technische Daten
Produktname: MIJIA 360 Kamera
Modell: QJXJ01FJ
Abmessungen: 78,00 x 67,40 x 24,03 mm
Gewicht: 108,3 g Brennweite: 1,43
Eingang: 5 V 2 A Blende: f/2.0
Akkukapazität: 1600 mAh Schutzart: IP67
Stromverbrauch im Standby-Modus: 3,8 W
Lagertemperatur: -20 bis 45 °C
Luftfeuchtigkeit bei Lagerung: 10–90 %
Bildauflösung: bis zu 6912 × 3456
Videoauflösung: bis zu 3840 × 1920
WLAN-Konnektivität: WLAN IEEE 802.11b/g/n 2,4 GHz, Bluetooth 4.0
Speicherweiterung: microSD-Karte (bis zu 128 GB, mindestens Klasse 10); für
Videoaufnahmen höchster Auflösung U3 microSD-Karten verwenden
Systemanforderungen: Android 5.0/iOS 9 oder höher
Empfohlene Adapterspezifikationen
Eingang: 100–240~50/60 Hz
Ausgang: 5 V 2 A/9 V 2 A/12 V 1,5 A
Unterstützte Standards: QC 2.0