Malacrino System One Plus Parts list manual

Date of publication 15th October 2014
www.malacrino.co.uk
- 1 -
Malacrino Ltd
Unit B6, The Dresser Centre,
Whitworth Street,
Openshaw,
Manchester,
M11 2NE
Tel [phone]
Fax [phone]
Email [e-mail]
www.malacrino.co.uk
System One Plus Electric Fire ( System One Model )
Instructions for Installation,
Use and Maintenance

Date of publication 15th October 2014
www.malacrino.co.uk
- 2 -
Parts Supplied
1 * lectric fire 1 * Three piece 1 * Decorative 1 * Type X
Decorative trim Fret attachment
Mains Lead
1 * 13 Amp Three Pin Plug
Fittings Supplied
4 * 4 by 30 cross head screws 6 * 4.2 by 6.5 self tapping screws 4 * 6 mm red
plugs
Tools Required
1 * Suitable cross head screwdriver
1 * Power drill
1 * Power drill bit (6 mm)
Before Commencement
1. Please read these instructions carefully before you start the installation
2. Check the pack and make sure all parts listed on page two are present and correct
3. When you are ready to start, make sure you have the correct tools and plenty of space with a
clean dry area for installation
4. Check that the supply voltage on the rating label is in accordance with your electric supply

Date of publication 15th October 2014
www.malacrino.co.uk
- 3 -
5. Warning this appliance must be earthed
6. This appliance is designed to be wired into a 13 amp double pole switched fixed spur
7. If a standard 13 amp three pin plug is decided to be fitted then follow the instructions of the
standard three pin plug manufacturer
8. Do not install this appliance into a chimney opening, it must be blocked to prevent any draft
affecting the heater fan unit, the overheat limit switch may activate and disable the appliance
9. Do not use this heater in any surroundings where water is present, such as bathrooms or
swimming pools
10.Do not locate this fire onto thick pile carpet
11.Do not place clothing or objects in front of the heater outlet, it may cause overheating or fires
12.This appliance uses fans to produce the realistic flame effect and to disburse the heat, as a
result their may be some normal residual back ground noise while they are in operation
13.Please keep these instructions for future reference
14.This appliance is not designed to be a primary heat source
Installation
1. The switched fused spur or three pin mains plug must be accessible after installation
2. nsure that adequate space is available to route the electric supply cable
3. This appliance has one installation option
4. The minimum size of the opening is 385 mm wide by 545 mm high and 75 mm deep
5. The maximum size of the opening is 420 mm wide by 570 mm high and 100 mm deep
Option one (direct screw fitting)
Fix the four screws provided at the dimensions listed below, In the event the screw cannot self
screw into the fixing material, drill a 6 mm hole into the material using a suitable drill and drill bit
and insert the red plugs to fix into, taking care not to damage the hard material
450 mm
435 mm 435 mm
104 mm 104 mm

Date of publication 15th October 2014
www.malacrino.co.uk
- 4 -
1. Remove protective wrapping and slide the left hand decorative trim under the retaining clips
on the left side on the fire taking care not to scratch the face ( Step A )
2. Remove protective wrapping and slide the right hand decorative under the retaining clips on
the right side of the fire taking care not to scratch the face of the fire ( Step B )
3. Remove protective wrapping and slide the top decorative trim over the left and right hand
decorative trims and into the retaining clips ( Step C )
4. Using the self tapping screws provided attach the decorative trim to the appliance main outer
frame at the rear of the fire through the pre drilled holes, be careful not to over tighten the
screws
Step A Step B Step C
5. Insert the type X male attachment mains lead into the base of the fire where the X attachment
female slot is located, once located, use the cable ties provided to secure the lead in either left
or right position as per installation requirement
6. Slide the fire into its desired fixing location, feeding the power cable towards the power source
at the same time
7. Tighten the 4 by 30 screws supplied until the fire fits snuggly over the screw heads
8. Slide the decorative fret onto the four locating screws at the bottom of the fire ( step D to F )
Step D Step Step F
9. Connect the appliance to the power supply using the desired method of connection

Date of publication 15th October 2014
www.malacrino.co.uk
- 5 -
Care and Use
1. This appliance is manual operation
2. This appliance can be used by children from 8 years old and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance in a safe way and understand
the hazards involved.
3. Children shall not play with the appliance.
4. Cleaning and user maintenance shall not be made by children without supervision.
5. Children of less than 3 years should be kept away unless continuously supervised
6. Children aged from 3 years and less than 8 years shall only switch on / off the appliance
provided it has been placed or installed in its intended normal operating position and they
have been given supervision or instruction concerning use of the appliance in a safe way and
understand the hazards involved.
7. Children aged from 3 years and less than 8 shall not plug in, regulate and clean the appliance
or perform user maintenance
8. CAUTION - Some parts of this product can become very hot and cause
burns. Particular attention has to be given where children and
vulnerable people are present
Switch One; Power On / Off and realistic flame effect
The appliance will power up and the realistic flame effect will display
Switch two; One Kilowatt heat setting ( half heat )
The appliance will deliver one kilowatt of heat
Switch three; Two kilowatt heat setting( full heat )
The appliance will deliver two kilowatt of heat,
Please note switch two must be on for switch three to function
Knob 1; Thermostat
Turn Clockwise ; High heat setting
Turn anticlockwise ; Low heat setting

Date of publication 15th October 2014
www.malacrino.co.uk
- 6 -
Thermal cut out
CAUTION
In order to avoid a hazard due to inadvertent resetting of the thermal cut-out this
appliance must not be supplied through an external switching device, such as a timer, or
connected to a circuit that is regularly switched on an off by a utility.
The thermal cut-out fitted in the heater is non-self- resetting that is reset by
disconnecting it from the mains.
The appliance is fitted with a thermal cut out, if the appliance fails to operate, the thermal protector
may have operated and set the appliance to no heat status.
In this event switch off the appliance at the double pole switched fuse spur or remove the three pin
plug from the socket and allow the appliance to cool and investigate the activation
Remove any item covering the heater or restricting the air flow. Switch on the double pole switched
fuse spur or insert the three pin plug. Operate the switches to restore the full operation
TO RESET THE THERMAL CUT OUT POWER TO THE APPLIANCE MUST BE DISABLED AND
THEN REAPPLIED
Cleaning and Servicing
1. For general cleaning use a soft clean duster or soft brush, a vacuum cleaner may be used on
the fuel effect bed
2. The decorative trims on this appliance have protective coatings; remove from the appliance
before cleaning with warm soapy water and a soft cloth
3. Do not use scorers, abrasives or chemical cleaners
4. Always turn off the appliance and isolate the power supply before and maintenance
5. If the supply cord ( type X attachment ) is damaged it must be replaced by a special cord or
assembly available from the manufacturer or its service agent.
6. This appliance is fitted with a 1.5 Watt GU10 Led light bulb, to replace this bulb, switch off
and then isolate the appliance, remove the front fret with an upward and outwards sliding
motion, using a cross head screwdriver, remove the 4 screws holding the cover plate on,
remove the GU10 light bulb and replace with a 1.5 Watt GU10 L D light bulb, refit the cover
plate and fret
Disposal of appliance
This appliance is constructed from recyclable material, at the end of its life it should be recycled and
not disposed of as household waste, it can be returned to Malacrino Ltd or taken to your local
recycling centre for correct disposal
Malacrino Ltd registration no. W /GJ4682ST

Date of publication 15th October 2014
www.malacrino.co.uk
- 7 -
Technical Data
A; 475 mm
B; 590 mm
C; 135 mm
D; 530 mm
; 150 mm
F; 20 mm
G; 350 mm
H; 65 mm
Frequency; 50 Hz Fuse; 13 Amp Voltage; 220 - 240 Volts
Minimum heat output 1000 Watts Maximum heat output 2000 Watts
Consumption on flame effect 1.5 Watt Length of cable; 1.9 metre ( aprox )
Spare Parts
This Document can be viewed and downloaded at www.malacrino.co.uk
Spare parts can be viewed and purchased at www.malacrino.co.uk
In the event you require service please call 0161 231 6979, email [e-mail] or write to
Malacrino Ltd , Unit B6, The Dresser Centre, Whitworth Street, Openshaw, Manchester, M11 2N
In order to assist us with your requirements , please quote the fire serial number, this can be found
in the format of a label behind the fret and starts with the letter " ML "
All warranties are subject to our standard terms and conditions
Specifications can change and vary at any time, it is advised to physically check all aspects before
installation
This appliance has been independently tested and certified to the following specifications
BS N 60335-1 : 2012 and BS N 60335-2-30 : 2009+A11 : 2012

Date of publication 15th October 2014
www.malacrino.co.uk
- 8 -