M&M Sales Enterprises, Inc. Monkey Jump Junior MM00184 User manual

MM00184-Monkey Jump Junior
ASSEMBLY INSTRUCTIONS
WARNING
• Due to the presence of small parts during assembly, keep out of reach of children unl assembly is
complete.
• To prevent serious injury, children must not use Monkey Jump Junior unl properly installed. Do not
use if any damage or deterioraon is detected or parts are missing. Contact point of purchase retailer
or M&M Sales Enterprises, Inc.
• Never substute parts.
• Please keep instrucons for future reference.
BEFORE YOU BEGIN ASSEMBLY
• Assembly should be completed by adult person(s). We intend for our products to bring joy not
frustraon and because the Monkey Jump Junior is meant to enjoy with friends too – in that same
spirit we say invite a friend (or someone you can spend at least 30 minutes with) to help you assemble
your Monkey Jump Junior.
• Place the equipment on level ground, not less than 6 . from any structure or obstrucon such as a
fence, garage, house, overhanging branches, laundry lines, or electrical wires.
• No need to show gorilla strength while ghtening bolts. Overghtening bolts or nuts can cause the
threads to get damaged making it dicult to take your Monkey Jump Junior apart or reassemble it in
the future.
HERE WE GO!
Lay out all box components included on a 6 . x 6 . level and comfortable workspace:
Assemble Pole Secons
1. The pole secon will be put together upside down for simplicity and then mounted onto the base. Place
the Boom Plate against the Top Plate boom side down so that the holes in the two plates align.
2. Insert the shorter length side of the Angled Top Pole into a pole pocket in the middle of the plate
sandwich. Place a Regular Washer on the Large Bolt and insert from the underside of assembly,
through the Top Plate, Angled Top Pole and Boom Plate.
3. Add an addional Regular Washer, Lock Washer and Locknut, in this order, to the Large Bolt end. Hand
ghten only.
4. Choose the same color Angled Top Pole and enter it opposite of its twin in the plate sandwich. Repeat
steps 2-4 ve more mes. Once complete, fully ghten all Large Bolts with the Hexagon Key Tool
included.
5. When complete, it should look like image below.
6. Once all poles are installed into their pole pockets (matching colors installed opposite of each other in
the plates) insert the corresponding color Angled Leg Pole into Top Pole unl holes align.
7. Once aligned, insert Set Screw.
8. Tighten with the Hexagon Wrench provided unl the Set Screw is ush with the exterior surface of the
base tube.
9. Repeat steps 7-8 ve mes. When complete, ip the Monkey Jump Junior right-side up to resemble the
image below.
MM00184 INSTRUCTION MANUAL
ASSEMBLY • INSTALLATION • OPERATION • MAINTENANCE • SAFETY
junior
WHATS IN THE BoX
Lay out all box components
included on a 6 . x 6 . level
and comfortable workspace:
Top Plate
Boom Plate
Angled Top Poles
Angle Leg Poles
Base Poles
Inner Tube
Hexagon Wrenches*
Hexagon Key Tool*
Large Bolts
Lock Nuts*
Lock Washers*
Regular Washers*
Set Screws*
Base Bolts*
STEP 1 STEP 2 STEP 3 STEP 4 STEP 5 STEP 6 STEP 7
STEP 8 STEP 9 STEP 10 STEP 11 STEP 12 STEP 13
SINGLE OR
MULTI-JUMPER
YEAR-ROUND
ENTERTAINMENT
SAFETY-RATED
TO 400 LBS
RECOMMENDED
FOR AGES 3+
LBS.
400
Connecng Base to Poles
10. Take one Base Pole and align the two pre-drilled holes with two Angled Leg Poles.
11. Insert both Base Bolts where the holes align and ghten by hand.
12. Take another Base Pole and press the buon in, insert, and release to lock. Repeat steps 10-12 two
more mes. Once all six Base Bolts are hand-ghtened and ush with the exterior surface of the Base
Poles they can be ghtened all the way with the Hex Wrench provided.
Adding the Bounce: There are two opons for Inner Tube inaon: 1.) Have tube professionally inated for no
charge by a re store; this opon is recommended to reach opmal inaon. OR 2.) A home compressor will
work but be sure to maximize inaon. NOTE: If blown up too big, the tube can pop. However, if not enough air
is pumped, the tube can seem at and jumping will not be ideal. Feet should not hit the ground or base tubing if
inated to correct level.
13. Aer your Inner Tube has been inated, slide the tube, with the nozzle facing down or to the ground
surface/oor, over the top of the assembled Monkey Jump Junior. You can blow it up about half-way
unl to forms some shape then slide over pole assembly and complete the inaon or inate fully and
applying downward pressure move the tube down the pole assembly to the base. When inated, the
tube should measure approximately 16-18” high and ve feet wide. Inate the Inner Tube with enough
air that the jumpers will not hit the ground surface below the Inner Twube while jumping. Standard
Inner Tube inaon is ~6 psi (40kpa). The nal assembled Monkey Jump Junior should resemble the
image below. NOTE: CONTINUED ON BACK SIDE
(1)
(1)
(6)
(6)
(3)
(1)
(2)
(1)
(6)
(6)
(6)
(12)
(6)
(6)
*50% of Actual Size
Replacement tubes
are available online at
mandmaslesinc.com
or by contacng M&M
Sales Enterprises, Inc.
at 877-242-0154.

OPERATION INSTRUCTIONS
Observing the following statements and warnings reduces the likelihood of serious or fatal injury:
1. Only for family residenal domesc use.
2. Designed for 1-6 children.
3. Maximum fall height 4.5 . (determined by product’s tallest height)
4. Jump safely with on-site adult supervision for children of ages 3+
5. Instruct children: Do not walk close to, in front of, behind, or between moving users of equipment • Do not use equipment in a manner
other than intended • Not to dismount equipment while they are in moon
• Not to wear inappropriate items, such as but not limited to, loose ng clothing, hood and neck drawstrings, scarves, cord-
connected items, capes, and ponchos. These items can cause death by strangulaon • Do not use equipment when wet • Not to
aach items to the equipment that are not specically designed for use with the equipment, such as, but not limited to, jump ropes,
clothesline, pet leashes, cables and chain as they may cause a strangulaon hazard • To remove bike or other sports helmet before
playing on the equipment • Wear well-ng and full foot enclosing footwear. Exam+p in an area safe of obstrucons on ground, air, or
sky that maybe encountered during jumping.
6. Locate Monkey Jump Junior on level, at ground surface that has grass, padding, or carpet under and surrounding it.
7. Carefully step onto the inated Inner Tube while securely grasping the vercal poles with both hands. Begin to jump. Hold bars with
both hands at all mes during bouncing or while standing on tube if others are bouncing. The security of holding onto the supporve
vercal poles is one of the reasons that this equipment so much safer than a tradional spring trampoline.
8. Jump upright. Do not jump and invert or ip.
9. In direct sunlight, inner tube and poles may become hot to the touch. Check that surfaces are not too hot for comfort and safe use.
Keeping your Monkey Jump Junior out of direct sunlight and extreme heat of summer months will maintain the life of the equipment.
If using outdoors, placing the Monkey Jump in a shaded area is preferred. Moving the Monkey Jump Junior indoor to outdoor or from
room to room doesn’t require full disassembly. The Monkey Jump tube should be slid up and over the pole unit. Unscrew the base
from the vercal pole assembly.
10. The Monkey Jump Junior can now be moved easily through a standard door frame in three secons: tube, base, vercal pole assembly.
Reassemble completely prior to beginning use in new locaon.
WARNING: This product contains one or more polycyclic aromac hydrocarbon chemicals (PAHs) know to the State of California to cause
cancer and birth defects or other reproducve harm. To learn more visit oehha.ca.gov/proposion-65.
MAINTENANCE INSTRUCTIONS
INNER TUBE MAINTENANCE: In order to ensure a great bounce, ensure the Inner Tube is inated to the recommended PSI. It will require
adding addional air from me to me. Please be aware, the lifespan of the inner tube will be determined by several factors. Direct sunlight,
over inaon of the tube, sharp objects, and other misuses will increase the chances of a blown Inner Tube. The pole assembly is powder coated
and will hold its color for years to come.
BEFORE EACH USE: Inner Tube should be visually inspected for proper inaon and any signs of visible damage that might cause it to pop during
use. Avoid using any objects that might cause damage to the Inner Tube during play.
AT THE BEGINNING OF EACH PLAY SEASON: Tighten all hardware • Check all protecve coverings on bolts, pipes, edges, and corners • Replace if
they are loose, cracked, or missing • Check all moving parts including poles, hardware, and tube for wear, rust, or other deterioraon. Replace as
needed • Check all metal parts for rust. If found, sand and repaint using a non-lead based paint meeng the requirements of 16 CFR 1303
TWICE A MONTH DURING PLAY SEASON: Tighten all hardware • Check all protecve coverings on bolts, pipes, edges, and corners. Replace if
they are loose, cracked, or missing
ONCE A MONTH DURING PLAY SEASON: Check all moving parts including poles, hardware, and tube for wear, rust, or other deterioraon.
Replace as needed.
AT THE END OF EACH PLAY SEASON OR WHEN THE TEMPERATURE DROPS BELOW 32°F: Take product inside for indoor use.
DISPOSAL: Owners shall be responsible for maintaining the legibility of the warning labels. When you are ready to dispose of the product, make
sure that all components are disposed of in accordance with local waste ordinances. Disassemble and dispose of the playground equipment in
such a way that no unreasonable hazards will exist at the me the playground equipment is discarded.
Replacement parts can be ordered by contacng M&M Sales Enterprises, Inc. 1-877-242-0154.
WARNING: Failure to carry out these checks and inspecons could result in fall, head injury, or death due to falls from equipment placed over
hard surfaces or misuse of product.
SAFETY INFORMATION
To reduce the likelihood of injury please follow the
guidelines as outlined in these instrucons. You can
visit our website mandmsalesinc.com to review the
instrucon manual in the future or keep this instrucon
sheet for reference: Monkey Jump Junior MM00184.
The installaon instrucons above are reecve
of the U.S. Consumer Product Safety Commission’s
Outdoor Playground Safety Handbook. For a complete
descripon of installaon instrucons and warnings
for outdoor playground equipment you can visit our
website at mandmsalesinc.com to link to the current
CPSC handbook and review in its enrety.
Our products are tested to ensure safety and
compliance with Consumer Product Safety
Improvement Act of 2008 (CPSIA) including
specicaons for lead paint and phthalates and
ASTM Internaonal F1148 Standard Consumer Safety
Performance Specicaons.
M&M Sales Enterprises, Inc.
1300 Synergy Ct., Dubuque, IA 52002 | 877-242-0154 | www.mandmsalesinc.com