Maradyne JETSTREME I User manual

TA9001105 REV 6 011023
MFA107
MARADYNE®High Performance Fans
4540 W. 160th Street • Cleveland, OH 44135 • Ph: [phone] • Fx: [phone] • www.maradyneHP.com
© 2023 MARADYNE®High Performance Fans - All rights reserved
Page 1 of 2
MOUNTING
BRACKET
(4)
1.25
[31.75]
¼" -20 x 1.25 L
HEX BOLT
(4)
1.5
[38.1]
5.5
[139.7]
BRACKET INSTALLED
Fig 1
JETSTREME I
JETSTREME II
MOUNTING BRACKETS ¼˝−20 X 1.25 HEX BOLTS
Package Contents
QUANTITY DESCRIPTION
4 Mounting Brackets
4 ¼" – 20 x 1.25 Hex Bolts
JETSTREME I & II MOUNTING INSTRUCTIONS
FOLLOW INSTRUCTIONS CAREFULLY TO PREVENT PERSONAL INJURY AND/OR DAMAGE TO THE FAN UNIT OR COMPONENT!
ALWAYS DISCONNECT ONE OF THE BATTERY CABLES OR REMOVE POWER FUSES FOR A CIRCUIT WHEN INSTALLING AN
ELECTRICAL FAN OR COMPONENT!

NOTE: Do not remove label from underside of shroud as this will void the products
limited warranty.
NOTE: The fans contained in this assembly are assembled in puller configuration from
the factory. While these fans can be reversed to be pusher fans, We do not recommend
using this assembly as pusher fans on the front side of the radiator due to the large
amount of ram air that is blocked by the shroud. Fans used as pushers should only be
used as a last resort when there are no other options for mounting.
NOTE: We DO NOT recommend the use of nylon tie kits or any other “through core”
mounting methods for this fan assembly. The motor used in this fan assembly is too
heavy and produce too much starting torque to be supported by the radiator fins.
We recommend using a prefabricated mounting kit MFA107 (included) or fashioning
metal brackets that will attach to at least four of the six ¼ - 20 nylon reinforced nuts
pressed in the back of the shroud and then bolted to the U-channels of the radiator/heat
exchanger (See Fig 1.). 1” X ¼-20 bolts are recommended to attach the brackets to the
shroud. Bolts must NOT be long enough to contact the radiator/heat exchanger. See
Fig 2 on page 2 for bolt pattern.
SEE JETSREME WIRING INSTRUCTIONS FOR WIRING INFORMATION
MJS13K
130 W
1,155 CFM
13.5” w x 15” h
3.31”
7.2
MJS16K
160 W
1,300 CFM
13.5” w x 15” h
3.70”
12.4
MJS12KPS
225 W
1,700 CFM
13.5” w x 15” h
4.02”
14.7
MJS23K
(2) 130 W
2,310 CFM
26” w x 15” h
3.31”
7.2
MJS26K
(2) 160 W
2,600 CFM
26” w x 15” h
3.70”
12.4
MJS22K
(2) 225 W
3,100 CFM
26” w x 15” h
4.02”
14.7
MJS22KPS
(2) 225 W
3,400 CFM
26” w x 15” h
4.02”
14.7
SPECIFICATIONS
LL HEAVY DUTY MOTOR
AIR FLOW @ 0” STATIC
SIZE
DEPTH (WITH SEAL)
AMP DRAW

TA9001105 REV 6 011023
MFA107
MARADYNE®High Performance Fans
4540 W. 160th Street • Cleveland, OH 44135 • Ph: [phone] • Fx: [phone] • www.maradyneHP.com
© 2023 MARADYNE®High Performance Fans - All rights reserved
Page 1 of 2
Fig 2
JETSTREME I & II MOUNTING INSTRUCTIONS (CONTINUED)
JETSTREME I
JETSTREME II