Marvel 3SWCE-BB-G User manual

A Division of Northland Corporation
R

A 3 1/2 INCH TOE KICK OR 7 SCREWS FOR A 4 INCH TOE KICK.
THE WOOD FRAME. A TOTAL OF 8 SCREWS WILL BE NEEDED. FOR
2. ONLY USE PAN HEAD SCREWS.
3. DO NOT SELECT A SCREW THAT IS LONGER THAN THE WOOD
4. USE RECOMMENDED PILOT HOLES FOR THE FRAME MATERIAL (SEE
1. A #8 PAN HEAD WOOD SCREW SHOULD BE USED TO PROPERLY SECURE
THICKNESS AT THE SCREW LOCATIONS.
CHART BELOW)
THIS SURFACE PARALLEL TO THE UNIT.
(RIGHT HAND SWING DOOR SHOWN)
1. ATTACH THE TOP AND BOTTOM DOOR HINGES TO THE DOOR WITH THE
10-32 MACHINE SCREWS AND A 1/8 INCH ALLEN HEAD DRIVER AS SHOWN IN
THE FIGURE BELOW.
2. PRESS IN THE SHOULDER BUSHINGS TO THE TOP AND BOTTOM DOOR
HINGES. MAKE CERTAIN THAT THE SHOULDER IS TO THE OUTSIDE OF THE
DOOR AS SHOWN IN THE FIGURE BELOW.
3. TEST FIT THE DOOR TO THE UNIT TO MAKE CERTAIN DOOR WILL HANG
CORRECTLY. THE DOOR IS HUNG CORRECTLY WHEN THE TOP OF THE DOOR
IS PARALLEL TO THE TOP OF THE UNIT. ADJUSTMENTS CAN BE MADE BY
LOOSING THE DOOR HINGE MACHINE SCREWS AND MOVING THE DOOR HINGE
ON THE DOOR.
4. TIGHTEN ALL FOUR MACHINE SCREWS AFTER ADJUSTMENTS HAVE BEEN
MADE.
5. REMOVE THE DOOR FROM THE UNIT BY REMOVING THE UNITS TOP HINGE
SET SCREW AND ANGLING THE DOOR OFF OF THE BOTTOM HINGE PIN.
DOOR FRONT
SURFACE
DOOR HINGE
SCREW HOLES
TYPICAL
TOP AND
BOTTOM
DOOR HINGE
ASSEMBLY
SHOULDER BUSHING
DOOR HINGE
10-32 MACHINE
SCREWS

R
TO THE UNIT AND WHEN THE WOOD IS POSITIONED
HINGE HOLE AFTER THE DOOR HAS BEEN ALIGNED
CLEARANCE HOLE. LOCATE AND DRILL USING DOOR
(NON-FACE) SIDE
MOUNTING SURFACE
ON DOOR.
Ø0.25 X 0.375 DEEP HINGE SCREW
SURFACE
TOP
TO THE UNIT AND WHEN THE WOOD IS POSITIONED
HINGE HOLE AFTER THE DOOR HAS BEEN ALIGNED
CLEARANCE HOLE. LOCATE AND DRILL USING DOOR
MOUNTING SURFACE
(NON-FACE) SIDE
MOUNTING SURFACE
(NON-FACE) SIDE
ON DOOR.
Ø0.25 X 0.375 DEEP HINGE SCREW
(NON-FACE) SIDE
MOUNTING SURFACE
(NON-FACE) SIDE
TYP
7.81
(COVERS THE ENTIRE DOOR EXTRUSION)
TO THE UNIT AND WHEN THE WOOD IS POSITIONED
HINGE HOLE AFTER THE DOOR HAS BEEN ALIGNED
CLEARANCE HOLE. LOCATE AND DRILL USING DOOR
FOR A 3.5 INCH TOE KICK
ON DOOR.
Ø0.25 X 0.375 DEEP HINGE SCREW
TOE KICK HEIGHT)
(TO MATCH EXISTING CABINETRY
OPTIONAL FOR A 4 INCH TOE KICK
TO THE UNIT AND WHEN THE WOOD IS POSITIONED
HINGE HOLE AFTER THE DOOR HAS BEEN ALIGNED
CLEARANCE HOLE. LOCATE AND DRILL USING DOOR
(NON-FACE) SIDE
MOUNTING SURFACE
ON DOOR.
Ø0.25 X 0.375 DEEP HINGE SCREW
MOUNTING SURFACE

BOTTOM HINGE CORNER
CAUTION
DOOR CAN BECOME
DISENGAGED IF WASHERS
ARE NOT INSTALLED
TOP HINGE CORNER
SHOULDER BUSHING
.75 OD X .443 ID
.75 OD X .257 ID
SHOULDER BUSHING
WASHER
3 NYLON
HARDWARE
COMPONENTS
AT BOTTOM
HINGE
HARDWARE
COMPONENTS
AT TOP HINGE
2 NYLON
NOT INSTALLED AS SHOWN
COMPONENTS ARE NOT
PROPERLY-IF ALL NYLON
DOOR MAY NOT SWING
.625 OD X .218 ID
WASHER
WASHER
CAUTION
6. INSTALL THE DOOR TO THE UNIT. USE THE SUPPLIED PLASTIC WASHERS AS SHOWN IN THE FIGURE BELOW.
2. PEEL BACK DOOR GASKET TO EXPOSE THE SCREW HOLES.
3. SET THE WOOD FRAME FLUSH TO THE FRONT OF THE DOOR IN THE DESIRED LOCATION. CLAMP WOOD FRAME TO
THE TOP HINGE. REMOVE THE DOOR BY ANGLING THE DOOR OFF OF THE BOTTOM HINGE PIN.
1. IF THE DOOR IS ATTACHED TO THE UNIT, REMOVE IT BY UNSCREWING THE TOP ALLEN HEAD SET SCREW AT
THE DOOR IF NECESSARY.
4. INSERT THE WOOD SCREWS THROUGH THE BACK OF THE DOOR INTO THE PILOT HOLES IN THE WOOD FRAME AND
5. REINSTALL DOOR GASKET BY PRESSING INTO DOOR CHANNEL. MAKE CERTAIN THE CORNERS ARE INSERTED FULLY.
7. REALIGNING THE DOOR MAY BE NECESSARY. ANY FINAL DOOR ADJUSTMENTS CAN BE MADE USING A 1/8 INCH ALLEN
8. ATTACH THE DOOR LIGHT STRIKER PLATE AS SHOWN USING THE HEX OR PHILLIPS HEAD SCREWS PROVIDED. MAKE
TIGHTEN.
HEAD DRIVER TO ADJUST THE DOOR'S HINGES (SEE FIGURE BELOW).
CERTAIN THE LIGHT IS ABLE TO TURN ON AND OFF WHEN THE DOOR IS OPENED AND CLOSED.
9. ATTACH THE DOOR TO THE UNIT BY REVERSING STEP NUMBER 1 ABOVE.
CAUTION
DOOR CAN BECOME
DISENGAGED IF WASHERS
ARE NOT INSTALLED CABINET HINGE
WOOD
FRAME
WOOD
FRAME
DOOR HINGE
DOOR HINGE
HINGE HARDWARE
INSTALLATION DETAILS.