Maxon MDS Series Operating instructions

MDS Series
Wireless Speakers
Programming Guide
11535W 83rd Terrace, Lenexa, KS 66214
Toll-Free. 800-456-2071(US Only) 913-859-9515
Website www.maxonamerica.com

PROGRAMMING THE MDS SPEAKER
1. Speakers should be programmed before installation.
2. Power on only the speaker you want to program and wait for its power-up chime
before you start programming. Speakers are “powered on” when plugged into
a power source and/or their battery back-up switch is turned on with a charged
battery. Note: It may take up to 40 seconds for the speaker to boot up.
3. If programming more than one speaker, make sure that the other speakers are
unplugged and their battery back-up is turned OFF so that they do not interfere
during programming. Repeat this process for each speaker as you program
additional speakers.
4. With the speaker on, insert the USB Bluetooth Dongle into an available USB
port on the computer. (Speakers must be turned on first to hear a unique
“Connection chime”). Use only one programming dongle & computer at a time
to prevent interference when programming. Speaker and PC should be within
a few feet of each other so that the Bluetooth connection can occur.
Programmer does not need to be running for dongle to connect to the speaker.
PC PROGRAMMER
1. Install CPS Radio Speaker programming software onto the PC that has the
programming dongle.
2. Run CPS program and it will open to a blank page. You will need to read the
speaker or pull up a previously saved speaker file (.bin). If this is your first-time
programming, “read” the target speaker first by following the next couple of
instructions.
a. Select the COM port. If you unsure of the port number it can be found in the

Device Manager on your computer. The driver for the dongle is made by
Silicon Labs. In this instance it is COM8.
You will receive an error if the wrong COM port is selected.
b. Read the MDS-Speaker via the pull-down selection at the top under
“Programming” or by selecting the Read icon.
The reading process may start slow, but should take less than a minute.
If you get a read failed error, restart the process and make sure your
speaker is plugged in and turned on.

**If you are working with a previously saved speaker file:
a. Get to the main page and select “File” or the “Open” icon.
c. Locate the (.bin) file you previously saved to your computer, click on the file,
& open it in the CPS programmer.
3. Information stored in the speaker will now be displayed. Various items are selected
from the tree view on the left side of the screen. A description of each is shown
below.
Speaker Information
Displays technical information about the speaker. Items on this screen cannot be
edited.

Basic Settings
a. Speaker Alias: Alphanumeric name or number that will represent either
the speaker model number or the location of the speaker. Example:
Warehouse.
b. Boot Zone: Zone has a maximum or 32 channels as Channel Members.
These members correspond to the channel number. Members can be
arranged by moving a channel up or down in the list.
c. Speaker Audio Level: Volume is adjustable from 0 (mute) to 10 (loudest).
d. Current Channel: The current channel is settable by selecting the
channel index configured in the Zone.
e. Announcement Chime: When enabled, the speaker automatically emits
ascending tones at the beginning of a transmission to “introduce” the
subsequent incoming audio. When the person transmitting stops, the
speaker emits descending tones to signal to the listener that the
transmission has ended. You would use this feature to draw attention to
incoming announcements about to be broadcast through the speaker.
Zone
A zone can consist of digital, analog or mixed channels. This list of
channels would consist of your most frequently used channels. The
first channel member in the zone becomes the channel used for the
speaker. Only one zone is available. A maximum of 32 channels can

be in the zone.
Channel/DMR Menu
a. DMRDigiCh displays the ID of the speaker along with digital channel
information.
b. This chart makes it easy to create a list of channels by automatically
creating the number of channels, the channel name, color code and slot
number. There is a maximum of 502 channels.
c. In the example above, 109 channels were created. Start frequency was
input with an offset of 0.0125. It starts with Color Code 2 and is
incremented by 1 for each channel. When it reaches 15 for the Color
Code, it is repeated 0-15 sequentially for each set of 16 channels. “Apply”
must be clicked to save the changes. All of the fields can be edited if
needed.
DMR Digital Channel Edit

a. Channel Alias is the name that shows up on the display of the radio.
b. Slot 1 or Slot 2 are selectable and should match the transmitting radio.
c. RX Frequency of the speaker.
d. RX CC is the color code of 0-15.
e. RX Group List. Must be assigned first to become selectable. It is found at
DMR Settings/DMR RX Group List.
Analog Channel Menu
a. Analog Channel allows an easy way to create multiple channels
automatically. In this example it created 9 channels with the name of
each channel called “Analog ChannelX”. “X” is automatically
incremented from 1-9. Maximum number of channels is 402.
b. Start Frequency is 450.0125 and incremented by 0.0125 for each
channel created. CTCSS tones start at 67Hz and every 2nd tone is input.
This is the Tone Offset.
c. Squelch Level, Tail and Bandwidth are also selectable (see below).
d. Apply and Save to write the channels to the programmer.

Analog Channel Edit
a. Channel Alias is the name that shows up on the display of the radio.
b. Analog Bandwidth may or may not be selectable. This depends on the
software version. 12.5kHz or 25kHz
c. Tail Degree is the frequency shift to eliminate the squelch tail.
d. RX Frequency of the speaker.
e. RX Squelch Type is selectable for Voice Only, CTCSS, DCS and
Reverse DCS.
f. RX CTCSS is used to select the tone frequency.
g. RX DCS selects the DCS code or the Reverse DCS code.
h. RX Squelch Level adjusts the squelch from open squelch (0) to tight
squelch (5).
Mixed Channel Edit

A mixed channel allows the speaker to receive either a digital channel or an
analog channel without changing the channel on the speaker.
a. Channel Alias is the name that shows up on the display of the radio.
b. Digital Channel Type can’t be edited.
c. Digital Available Channel can be any channel in the DMR Digital
Channel list.
d. Analog Available Channel can be any channel in the Analog Channel list.
e. Mixed Channel Hang time is the number of seconds the receiver sits on
the channel when reception stops. Basically, a mixed channel is doing a
2-channel scan.
DMR Basic Settings
a. Displays the speaker ID number.
b. Call Hang Time is the number of seconds the channel stays open after
the call ends.
DMR Contacts
a. There are 3 types of contacts; Group Call, All Call and Individual Call.
b. A Group Call can talk through any speaker assigned to that Group
ID.
c. All Call talks through all speakers regardless of the Group ID or the
Individual Call ID.
d. An Individual Call is used to talk through a specific speaker.

DMR RX Group List
a. Multiple DMR Group lists can be made. In this instance
DMRRXGroupList 1 has the member Group 1.
b. Only Call Types with a Group Call are displayed.
4. Save Your Work
There are 2 ways to access Save as shown below.
or
Next type in the file name then Save.