MAXSA 40234 User manual

MODELS #40234
#40235
#40236
OPERATING INSTRUCTIONS
Solar Motion-Activated Wedge Light
IMPORTANT: READ ALL INSTRUCTIONS CAREFULLY BEFORE USE
ABOUT YOUR SOLAR WEDGE LIGHT
During the day, the solar cell charge panel on this MAXSA Solar Wedge
Light converts sunlight into electricity recharging the batteries. Using this
stored energy, the LED light (built into this Solar Security Light) turns on
automatically at night when motion is detected. This MAXSA Solar Wedge
Light turns on for 4 minutes each time motion is detected in the area.
This unit includes 3 AA rechargeable batteries, which will need to be
replaced when the charging ability is decreased.

CHOOSING A LOCATION FOR YOUR SOLAR WEDGE LIGHT
This Solar Wedge Light has a built-in solar panel. For optimum sun exposure and longer
light output, place the light with the solar panel in a position that receives at least 6-8
hours of direct sunlight per day. Ideally, the solar panel should face south. Placing the
solar panel in a shaded location will not allow the batteries to charge fully. This will
reduce the number of hours the Solar Wedge Light will operate per evening. In choosing
a location for your Solar Wedge Light, ensure that the solar panel is not placed near
night time light sources such as porch lighting or street lighting.
This Solar Wedge Light is ideal for areas where electricity is not available, including
driveways, carports, garages and entrance doors, for safety and security around your
home. In addition to the safety and security benefits of this Solar Wedge Light, it can
also be used for convenience lighting and is ideal for use on backyard sheds, farm
sheds, RV's and other remote areas where electricity is not available.
When deciding where to mount the light, keep in mind that the motion sensor that
activates this light has a field of vision of 100° (horizontal) at a distance of 22 feet when
the surrounding temperature is 77° F.
BEFORE FIRST TIME USE OF YOUR SOLAR WEDGE LIGHT
1. Ensure the power switch on the main body of your Security Light is in the OFF
position. In this position the solar cell will charge the batteries without activating the
light.
2. Leave the switch in this position for up to 3 days and make sure the solar panel is
placed in direct sunlight. This will ensure that the batteries in your Solar Security Light
have a full charge prior to normal operation.
OPERATING YOUR SOLAR WEDGE LIGHT
Your Solar Wedge Light will be ready for use at the end of the initial 3 day charging
period. You can now move the switch to AUTO if you want the light to be motion-
activated when it's dark or you can move the switch to ON if you want the light to stay on
all the time.
100°
Front View
Side View
2.3 ft 15 ft 22 ft
6.5 ft
2

HOW TO INSTALL YOUR SOLAR WEDGE LIGHT
The Solar Wedge Light can be mounted vertically or horizontally onto a solid surface
using the supplied mounting bracket, wood/sheet metal screws, and anchors.
If you are placing the light on a flat surface, mounting is not required. Remember it is
best to face the panel south for direct sunlight exposure.
The included mounting bracket and screws can be used to mount the Solar Wedge Light
securely to a wall or other stable surface.
To install the mounting bracket with screws:
1. Remove the mounting bracket from the bottom of the Solar Wedge Light by inserting
the key into the keyhole and twisting the key counter-clockwise to the OPEN
position.
2. If you are mounting the bracket on a very hard surface, you may need to drill holes
for the screws first. The included screw anchors can be used for drywall, cement,
brick, or similar surfaces.
3. Align the mounting bracket and install the two screws using a Phillips screwdriver.
4. Place the Solar Wedge Light onto the mounting bracket.
5. Insert the key into the keyhole and twist the key clockwise to the LOCK position.
6. Remove the key and gently nudge the Solar Wedge Light to make sure that it is
securely mounted.
3

REPLACING THE RECHARGEABLE BATTERIES
When the charging ability of the batteries decreases, you can replace the batteries with
(3) three new AA Ni-MH 1.2V rechargeable batteries. Follow the steps below when
replacing the battery.
1. First remove the Solar Wedge Light from its mounted surface.
2. Move the power switch on the main body to the OFF position.
3. Remove the five (5) screws on the battery compartment cover on the back of the
Solar Wedge Light.
4. Turn the main unit upside down and slide out the battery tray.
5. Carefully remove the old batteries from the battery tray by hand and replace with
three (3) new AA Ni-MH 1.2V rechargeable batteries. Ensure that the new batteries
are inserted in the correct +/- polarity orientation as indicated in the battery
compartment. (WARNING: Installing the batteries in the opposite direction could
damage the unit.)
6. Replace the battery compartment cover and reinstall the five screws.
8. Once assembled, mount your Solar Wedge Light to its original surface location.
8. Repeat the steps in the "Before first time use of your Solar Security Light" section on
page 4 to ensure your new batteries are fully charged.
NOTE: Do not dispose of batteries in general household trash or into a fire since the
batteries may explode. Consult your local regulations for correct disposal of
batteries. These batteries may also be returned to MAXSA Innovations at 8412
Cathedral Forest Dr., Fairfax Station, VA 22039. Do not take apart the batteries
since they contain corrosive chemicals.
GENERAL ELECTRICAL AND SAFETY WARNINGS
1. Do not install the Solar Wedge Light in a location where it can be accidentally kicked
or tripped over.
2. Do not immerse the Solar Wedge Light in liquid.
MAINTENANCE TIPS
To keep your Solar Wedge Light looking new, keep the lens free of dust and deposits by
wiping occasionally with a dry cloth or with warm soapy water if necessary.
Importantly, ensure that the solar panel is kept free of dirt and debris at all times. A dirty
solar panel will not allow the batteries to fully charge which will shorten the life of the
batteries and may cause the light to malfunction.
4

STORAGE
If you wish to store your light indoors for more than two or three days, turn the power
switch to the OFF position to prevent damaging the batteries. Battery capacity may be
reduced during prolonged storage. For optimal performance, we recommend that you do
not store your Solar Wedge Light for prolonged periods of time.
COLD WEATHER
In temperatures below 20°F, the Solar Wedge Light may not work as well. Normal
performance will return when the temperature rises.
Winter Tips: In winter, for northern locations, there is much less daylight and very cold
temperatures can affect the performance of your solar motion light. Also the sun’s
orientation in the sky can change dramatically from summer. Make sure your solar panel
is oriented southwards to the sun and gets maximum light. You may also want to lower
the time duration to the shortest time period to lesson battery use. Cold weather can also
affect the performance. These issues go away with warmer weather and longer days.
5