Maykke YSA1300101 User manual

Model:
REV.08042017SPECIFICATION SHEET www.maykke.com
SPECIFICATION SHEET
All measurements are approximate and may vary +/- 1/4"
Top
YSA1310101 Surrey 30” Fireclay Farmhouse Kitchen Sink
Front Side
29¾”
29¾” 18⁄”
17¼”
9⅛”
14⅜”
8⅞” 10¼”
16”
27⁄”
27⁄”
26⅞”
9⅛” 8⁄”
5¼”
3⅝”
1¾” 1¾”
18⁄”
10¼”
3⅝”
5¼”
1”

www.maykke.com
Fireclay Apron Sink
Installation, Care Guide
and Warranty
YSA1300101 YSA1310101

REV. 05102017INSTALLATION AND CARE GUIDEwww.maykke.com
INSTALLATION AND CAREGUIDE
1
Tools Required
PRE-INSTALLATION
MATERIALS INCLUDED
(1) fireclay kitchen sink
MATERIALS REQUIRED
(2) 2x4 cut to fit in cabinet
(1) 3/4” plywood
NOTICE: Do not change or modify the product in any way. Doing so may compromise the
products structural integrity and will void the warranty.
NOTICE: Installation instructions must be followed. Any diversions from the installations
may risk property damage and will void the warranty.
NOTICE: If you are unfamiliar with Sink installation please consult a professional.
result in damage to the product.
IMPORTANT:
Observe all state and local building codes.
Carefully read all installation and care instruction before proceeding.

REV. 05102017INSTALLATION AND CARE GUIDEwww.maykke.com
INSTALLATION AND CAREGUIDE
2
INSTALLING THE SINK
Step 1: Determine the ideal location of your
new fireclay kitchen sink.
Measure and cut the cabinet to fit the
kitchen sink.
See Figure 1.
Figure 1.
Step 2: Cut 2 pieces of 2x4 beams to attach to
the inside of the cabinet.
Note: It is highly recommended to
secure each 2x4 beam with wood glue
and screws.
See Figure 2.
Figure 2.
NOTE: To Install flush, mea-
sure the desired height of the
sink and cut the cabinet front
accordingly.

REV. 05102017INSTALLATION AND CARE GUIDEwww.maykke.com
INSTALLATION AND CAREGUIDE
3
Step 3: Follow the directions on the back of
the wood glue and allow enough time
for it to dry.
Fasten each 2x4 beam with wood
screws.
See Figure 3.
Figure 3.
Step 4: This step is optional.
Cut and fit a 3/4” thick plywood board
that sits on top of the beams.
This step is to ensure the bottom of
the sink has enough support.
Cut the area for the faucet lines and
drain / garbage disposal installation.
Secure the plywood board with wood
screws to the beams.
Verify the board is level.
See Figure 4.
Figure 4.

REV. 05102017INSTALLATION AND CARE GUIDEwww.maykke.com
INSTALLATION AND CAREGUIDE
4
Step 5: Place the sink over the plywood.
Verify the overall appearance and
check for levelness.
See Figure 5.
Figure 5.
Step 6: Place the countertop over the cabinets
and kitchen sink.
Verify the countertop is level.
See Figure 6.
Figure 6.

REV. 05102017INSTALLATION AND CARE GUIDEwww.maykke.com
INSTALLATION AND CAREGUIDE
5
Figure 7.
Step 1: Clean the surface of the cabinet and
sink with a damp cloth.
INSTALL THE VANITY TOP
Step 2: Verify the sink is installed properly.
Step 3: Apply a thin bead of silicone to the
surface of the cabinet and sink.
Carefully place the countertop on the
cabinets.
immediately.
Verify the countertop is level.
See Figure 7.
Step 4: Follow the directions on the silicone
tube to allow for ample drying time.
Refrain from moving/using the vanity
during this time.
Step 5: Install the faucet and drain per
manufacturers instructions.

REV. 05102017INSTALLATION AND CARE GUIDEwww.maykke.com
INSTALLATION AND CAREGUIDE
6
Fireclay Surfaces
The fine furniture finish of your new vanity, mirror or other bathroom accessories are designed to
protect against normal home use. Withproper care, your product will provide years of use and beauty
in your home.
General Care Tips
PRODUCT CARE AND MAINTENANCE
• We recommend using a soft sponge or cloth and a mild abrasive.
• To avoid water spotting, wipe down the sink bottom after use. Waxing the sink will
encourage drainage.
• Fireclay sinks from Maykke are constructed with a durable glaze
for years of beautiful performance. On the occasion that a metal pot or pan may leave a
mark on the surface of the sink, we recommend a mild abrasive cleaner is acceptable.
• Test cleaning product on small, discrete area prior to applying to entire surface.
• Wipe surfaces frequently with dry, soft, non-abrasive and lint-free towel.
• Do not allow liquids and moisture to accumulate on the surface of products.
• For warranty information, please visit our website at www.maykke.com or contact the
Customer Service Department at [phone].