MB QUART RVM2.0 User manual

RVM2.0 USER MANUAL
AM/FM ● Bluetooth®● USB ● HDMI ● Multi-Zone
Mini RV Media Receiver

PRE-INSTALLATION CHECKLIST
2
Thank you for purchasing the MB Quart RVM2.0 multi-zone mini RV radio with
AM/FM and Bluetooth audio streaming. Please take a few minutes to review
the user manual before attempting installation and operation.
Additional support documentation can be found at MBQUART.com or by
emailing [email protected].
FEATURES
AM/FM Radio (selectable USA/Europe)
Bluetooth Audio Streaming (HSP)
USB Audio Input (MP3/WMA)
HDMI Video Input and Pass-Thru Output
Front Panel AUX 1 Audio Input
Rear Panel AUX 2 Audio Input
Wired Headphone Jack
Multi-Zone Operation
Four (4) Built-In Speaker Outputs
Front/Rear/Subwoofer Preamp Outputs for External Amplifiers
Built-In Wake Up Alarm and Auto-Off Sleep Modes
Wired Headphone Output (Privacy Listening)
CHECKLIST
1. Please read the instruction manual carefully before installing the unit.
2. Please note this unit is intended for only 12V DC electrical systems.
3. Make connections to the unit as outlined in this instruction manual.
Incorrect connections may cause damage to the unit.
4. Make sure to connect and insulate all wires before powering on the unit.
5. Secure any loose wires after installation.
6. For HDMI front or rear-connected cables, please keep the overall length
12 feet or less.

WIRING & INSTALLATION
3
REAR PANEL DETAIL
WIRING DIAGRAM

WIRING & INSTALLATION
4
INSTALL THE UNIT
Please note: This unit requires a minimum 3” mounting depth which includes
space for the electrical/speaker plugs and any A/V input and output
connections.
1. Cut or utilize a mounting opening 3-7/8”(H) x 4”(W).
2. Remove the left and right decorative covers as shown in the diagram.
3. Insert the unit into the mounting opening.
4. Attach the unit using the four (4) supplied mounting screws.
5. Replace decorative side covers over mounting screws.

FRONT PANEL CONTROLS & INPUTS
5

FRONT PANEL FUNCTIONS (BY MODE)
6
BUTTON
ACTION
RADIO
USB
AUX IN
BT MUSIC
PWR/
DIM
Short
Power ON / Dimmer
Dimmer = H/M/L/OFF
Power ON / Dimmer
Dimmer = H/M/L/OFF
Power ON / Dimmer
Dimmer = H/M/L/OFF
Power ON / Dimmer
Dimmer = H/M/L/OFF
Long
Power OFF
Power OFF
Power OFF
Power OFF
ZONE 1
Short
Zone 1 Active or
Disabled
Zone 1 Active or
Disabled
Zone 1 Active or
Disabled
Zone 1 Active or
Disabled
Long
Zone 1 Mute ON/OFF
Zone 1 Mute ON/OFF
Zone 1 Mute ON/OFF
Zone 1 Mute ON/OFF
ZONE 2
Short
Zone 2 Active or
Disabled
Zone 2 Active or
Disabled
Zone 2 Active or
Disabled
Zone 2 Active or
Disabled
Long
Zone 2 Mute ON/OFF
Zone 2 Mute ON/OFF
Zone 2 Mute ON/OFF
Zone 2 Mute ON/OFF
MODE
Short
Source Selection
Source
Change/Search #7
Source Selection
Source Selection
Long
BT(OFF or LINK)
BT(OFF or LINK)
BT(OFF or LINK)
BT(OFF or LINK)
AS/
BAND
Short
AM or FM Band Select
Search
/
/
Long
Auto Store Presets
/
/
/
DISP
Short
Info/Clock
Info/Clock/Search #0
Info/Clock
Info/Clock
Long
Clock Setting
Clock Setting
Clock Setting
Clock Setting
I<<
Short
Seek Down
Previous File/Search
#8
/
Previous File
Long
Manual Down
FR
/
/
>>I
Short
Seek Up
Next File/Search #9
/
Next file
Long
Manual Up
FF
Reset (5seconds)
/
VOLUME
KNOB
Rotary
Volume Up or Down
Volume Up or Down
Volume Up or Down
Volume Up or Down
SEL
(PUSH
VOLUME
KNOB)
Short
BASS/TRE/BAL/EQ
BASS/TRE/BAL/EQ
BASS/TRE/BAL/EQ
BASS/TRE/BAL/EQ
Long
Alarm on/off-Alarm set-
Sleep on/off- Sleep set-
BEEP- CLOCK 12/24- P_VOL-
CT sync/indep -AREA-DX-
STEREO
Alarm on/off-Alarm set-
Sleep on/off- Sleep set-
BEEP- CLOCK 12/24- P_VOL
Alarm on/off-Alarm set-
Sleep on/off- Sleep set-
BEEP- CLOCK 12/24- P_VOL
Alarm on/off-Alarm set-
Sleep on/off- Sleep set-
BEEP- CLOCK 12/24- P_VOL
1/>II
Short
Recall M1 Station
Play/Pause/Search 1
/
/
Long
Save Station to M1
/
/
/
2/INT
Short
Recall M2 station
INT ON/OFF/Search 2
/
/
Long
Save station to M2
/
/
/
3/RPT
Short
Recall M3 Station
RPT(ONE/ALL)/
Search:3
/
/
Long
Save station to M3
/
/
/
4/RDM
Short
Recall M4 station
RDM on/off/Search 4
/
/
Long
Save station to M4
/
/
/
5/DIR-
Short
Recall M5 station
DIR-/Search #5
/
/
Long
Save station to M5
-10
/
/
6/DIR+
Short
Recall M6 station
DIR+/Search #6
/
/
Long
Save station to M6
+10
/
/

OPERATION
7
POWER AND BASIC ADJUSTMENTS
Turn the Unit ON or OFF
Press button to turn the unit ON. When the unit is switched on, press and hold button for
2 seconds to switch the unit OFF. A “GOOD BYE” message is displayed to confirm power down.
Sound Adjustments
Press and release VOLUME/SEL knob to choose sound settings in the following order: BASS-
TRE-BAL-EQ
Bass –Choose from -7 to +7
Treble –Choose from -7 to +7
Balance –Choose Left or Right (up to 7 steps in either direction)
EQ –If “OFF” turn knob to the right and choose from pre-programmed tone settings*:
oClassical
oRock
oPop
oFlat
oJazz
oEQ OFF
*Note: If one of the EQ sound settings is chosen, manual Bass and Treble adjustments are disabled.
Only “BAL” and the name of the EQ setting will show in the Sound Adjustment menu. To disable the
EQ and allow manual Bass/Treble setting, simply scroll through the settings until “EQ OFF” is
displayed.
Setting Adjustments (USB, Bluetooth or AUX Sources)
Press and hold VOLUME/SEL button for the setting menu: ALARM ON/OFF-SLEEP ON/OFF-
BEEP ON/OFF-CLOCK 12/24 - P_VOL
In each menu item, rotating the VOLUME/SEL knobselects them and allow you to rotate
through the sub-settings.
Setting Adjustments (AM/FM Source ONLY)
The AM/FM source adds additional settings to the adjustment menu. Press and hold
VOLUME/SEL button for the setting menu: ALARM ON/OFF –SLEEP ON/OFF -BEEP ON/OFF-
CLOCK 12/24 - P_VOL –CT SYNC or CT INDEP –AREA USA or AREA EUR–DX or LOC –
STEREO or MONO
In each menu item, rotating the VOLUME/SEL knobselects them and allow you to rotate
through the sub-settings. The additional AM/FM settings are:
oCT SYNC or CT INDEP –allows the clock to synch with the radio station’s RDS
time feed (SYNC) or to be set independently (INDEP) by the user
oAREA USA or AREA EUR –Selects the region: USA or Europe
oDX or LOC –Selects distance (DX) or local (LOC) for optimized reception
oSTEREO or MONO –Selects a stereo or mono broadcast reception

OPERATION
8
POWER AND BASIC ADJUSTMENTS (Continued)
Alarm Operation
The alarm built into the unit functions as a wake-up alarm. It could also be used to automatically
turn the unit on at a specific time (such as a meal or evening time to relax).
In setting menu turn ALARM to “ON” and set the wake-up alarm time (see below Alarm
Time Setting). When the wake-up alarm time is set, the unit will generate a wake-up
beeping sound at the preset time. The beep sound stops when any key pressed.
Alarm Time Setting Procedure
When ALARM is set to “ON”, the next menu item is ALARM SET.
Wait 2 seconds after turning the alarm to “ON” and the HH (hours) flash. Rotate the
VOLUME/SEL knob to set the hour. Next, press VOLUME/SEL knob. The MM (minutes)
flash. Rotate the VOLUME/SEL knob to set the minutes. Press the VOLUME/SEL button to
exit.
Sleep Operation
The sleep function built into the unit allows the user to set a specific time when the unit will
automatically turn off from 1-59 minutes later.
In setting menu setting turn SLEEP to “ON” then set the sleep time (see below Sleep Time
Setting). When the sleep time is set, the unit will power off automatically at the preset time.
Sleep Time Setting Procedure
When SLEEP is set to “ON”, the next menu item is SLEEP SET.
Wait 2 seconds after turning sleep time to “ON” and the sleep timer will flash. Rotate the
VOLUME/SEL knob to set it between 01-59 minutes. Press VOLUME/SEL button to exit.
Clock Setting Procedure
The clock allows you to select between 12 or 24 hour time formats.
To set the 12 or 24 hour time format, advance to the “CLOCK” function in the settings menu
and rotate the VOLUME/SEL knob to choose the format.
To set the clock time, press and hold DISP button and the HH (hours) flash. Rotate the
VOLUME/SEL knob to set the hour. Press DISP (or VOLUME/SEL) button until the MM
(minutes) flash. Rotate the VOLUME/SEL knob to set the minutes. Once complete, press
DISP (or VOLUME/SEL) button to exit.
Preset (P_VOL) Setting
This function allows the user to set the volume level at which the unit powers up again depending
on what level was recorded when the unit was last turned off. This avoids surprise high volumes.
To set the P_VOL threshold, advance to the “P_VOL” function in the settings menu and
rotate the VOLUME/SEL knob to choose the volume setting.
When the volume threshold at the time of unit turn off is less than P_VOL value, the next
time turns on the unit the volume will be the same as last time turned off.
When the volume threshold at the time of unit turn off is greater than P_VOL value, the
next time turns on the unit the volume will default to the lower P_VOL preset threshold.

OPERATION
9
ZONES, DISPLAY & AUX INPUTS
ZONE 1 Operation
ZONE 1 is connected to the unit’s on-board FRONT speaker and preamp-level RCA outputs.
Quickly press and release the ZONE 1 button to select between the zone being active or
disabled. The LCD screen will indicate the status of the zone above the button.
Rotate the VOLUME/SEL knob up or down to adjust the ZONE 1 volume when it is in the
active state.
When ZONE 1 is in the disabled state, the VOLUME/SEL knob only controls the active
zone. Otherwise, the ZONE 1 volume remains where it was left when disabled. To match
the output of ZONE 2 after re-enabling, simply turn the volume all the way down and back
to the desired level for both zones which then display equally.
To mute ZONE 1, press and hold the ZONE 1 button to toggle between ON or OFF. The
LCD screen indicates the muting status.
ZONE 2 Operation
ZONE 2 is connected to the unit’s on-board REAR speaker and preamp-level RCA outputs.
Quickly press and release the ZONE 2 button to select between the zone being active or
disabled. The LCD screen will indicate the status of the zone above the button.
Rotate the VOLUME/SEL knob up or down to adjust the ZONE 1 volume when it is in the
active state.
When ZONE 2 is in the disabled state, the VOLUME/SEL knob only controls the active
zone. Otherwise, the ZONE 2 volume remains where it was left when disabled. To match
the output of ZONE 1 after re-enabling, simply turn the volume all the way down and back
to the desired level for both zones which then display equally.
To mute ZONE 2, press and hold the ZONE 2 button to toggle between ON or OFF. The
LCD screen indicates the muting status.
Show Clock or Source Information
Press DISP button to show either the clock or source information. Depending on the source, text
information about the song playing may be available on the display (such as RDS-enabled FM
stations, USB music files or Bluetooth streamed music).
AUX Inputs
There are two methods for selecting an auxiliary input.
Press the MODE button to switch to AUX IN 1 or AUX IN 2 mode when an auxiliary audio
signal input is desired.
Choose AUX IN 1 for front panel 3.5mm jack. Choose AUX IN 2 for preamp-level RCA input
on the back of the unit.
Headphone Jack
There is a 3.5mm headphone jack in the front panel to allow for use of wired headphones.
When a headphone plug is inserted into the jack, the unit’s speakers are muted.

OPERATION
10
AM/FM RADIO
Receive a Radio Station
There are 3 FM station groups - FM1, FM2 and FM3. There are 2 AM station groups - AM1 and
AM2.
To select a radio station group, press the MODE button to select the radio mode. Next press
BAND button to select desired group (FM1, FM2, FM3, AM1 orAM2).
Press and quickly release the / button to tune by automatically seeking up or down
to the next available radio station frequency.
Press and hold the / button for manual tuning up or down to the desired frequency.
Manually Store and Recall Radio Station Presets
The unit offers 6 presets for each of the AM and FM station groups. There are a total of 18 FM
presets and 12 AM presets.
To store radio station presets, press and hold one of the preset button (1 through 6) for 2
seconds. The current station is stored into the number button.
To recall a given radio station preset, quickly press the preset button (1 through 6) to directly
listen the station saved in the corresponding preset button.
Auto-Store Stations
This is a useful method to populate available radio stations in a new area.
Press and hold BAND button for 2 seconds to automatically store stations to numeric buttons
1 through 6 of band 1, 2 or (if FM) 3. Stations will store in the order of scanning and reception.
Use front panel buttons 1 through 6 to recall presets.

OPERATION
11
USB Sources
When an USB source such as a thumb drive or portable media player is inserted to the USB port
on the front panel of the unit, it supports playback of MP3 and WMAfiles automatically.
To select USB as the source, press the MODE button until the USB mode display appears.
Selecting Music Files
Selecting the files uses the icon-based buttons below the LCD to the right. Refer to page 5for the
icon button locations.
Press the NEXT or PREVIOUS button to skip to next/previous file.
Hold the NEXT or PREVIOUS button to fast forward or fast reverse.
Play/Pause
To play or pause the song:
Press 1/ button to play/pause the file.
INTRO Function
The INTRO function plays the first 10 seconds of each file. To initiate INTRO:
Press 2/INT button.
Press again to stop this function.
Repeat (RPT) Function
The REPEAT function simply repeats the same chosen file(s) or folder again and again until de-
selected.
Press 3/RPT button to select RPT mode.
oRPT FOLD: Repeat all files of the folder.
oRPT ONE: Repeat the same file.
oRPT ALL: Repeat all files.
Random (RDM) Function
The RANDOM function simply randomizes all files. This is also called “shuffle” on some devices.
Press 4/RDM button to choose RDM on/off.
oRDM ON: Plays all files in random order.
oRDM OFF: Turns off the random function.

OPERATION
12
USB Sources (Continued)
Directory+/- Function
If you have a USB device set up with folders (such as by artist or playlist), the Directory function
allows you to navigate the folders for MP3 and WMA music files.
Press DIR+/ DIR- button to select next/previous folder to play. Once in the directory
function, use the +10/-10 to navigate the folders.
Press and hold DIR+/ DIR- button for 2 seconds it will skip +10/-10 file to play.
Search Songs
The unit allows users to directly input a song number or rotate through the dial to quickly get to a
specific song (file) on the USB device.
To search songs on a USB device, press the BAND button.
The display shows “NUM 0000.”
Rotating VOLUME/SEL (or directly enter number) to select the numbers then press
VOLUME/SEL to play.
oFor the number 1: Use preset button 1
oFor the number 2: Use preset button 2
oFor the number 3: Use preset button 3
oFor the number 4: Use preset button 4
oFor the number 5: Use preset button 5
oFor the number 6: Use preset button 6
oFor the number 7: Use the MODE button
oFor the number 8: Use the “Previous Track” button
oFor the number 9: Use the “Next Track” button
oFor the number 0: Use the DISP button

OPERATION
13
BLUETOOTH SOURCES
Bluetooth Pairing
You must first pair a Bluetooth-enabled device to stream music to your unit.
Select “search” or “discover” on the Bluetooth device while the unit is in the BT MUSIC mode.
“RVM2.0” should appear in the list of available devices. Select “RVM2.0.”
If a password is required, input “0000.”
When successfully paired, BT MUSIC is displayed on LCD.
If no Bluetooth device is paired, “UNPAIRED” will show in the LCD display.
Stream Bluetooth Audio
This unit supports Bluetooth music streaming using the Headset Profile (HSP). It also supports text
readout from compatible BT streams.
Using a Bluetooth-enabled device, press the MODE button to switch to BT MUSIC source. It
will play a song from the BT device automatically as long as it’s been selected in the music
player on the device.
Press the 1/ button to play/pause the song. Press button to select next/previous
song.
Disconnect Bluetooth Device
This is useful for mobile phones where the user wishes to place or receive a call.
When the Bluetooth device is paired with the unit. Press and hold the MODE button to
disconnect the Bluetooth. “BT OFF” is displayed.
Reconnect Bluetooth Device
This is useful if a Bluetooth-enabled mobile phone user has completed a call and wishes to continue
playing music via Bluetooth.
Press and hold the MODE button again to connect the previously paired Bluetooth device.
“LINKED” is displayed.

SPECIFICATIONS
14
GENERAL
Power Supply Requirements: DC 12 Volts, Negative Ground
Current Drain: 10 Ampere (max.)
Maximum Output Power: 4 x 17 watts into 4 Ohms @ 14.4V DC
Preamp Output Voltage: 2.1V (with AUX, USB orAM/FM Source)
1.5V (with BT Source)
Chassis Dimensions : 3-7/8”(H) x 4”(W) x 2”(D)*
*Note: Installation depth requires 3” minimum
Tone Controls:
Bass (at 100 Hz): ±10 dB
Treble (at 10 kHz): ±10 dB
RADIO FM AM
Frequency Coverage 87.5 to 108 MHz 520 to 1710 kHz
IF 10.7 MHz 450 KHz
Sensitivity 4μV(S/N=30dB) 36dBuV(S/N=20dB)
FM Stereo Separation >25dB N/A (AM is Mono)
TROUBLESHOOTING
Symptom
Cause
Solution
No power.
The vehicle’s ignition switch is
not on.
If the power supply is connected to
the vehicle’s accessory circuits, but
the engine is not moving, switch
the ignition key to “ACC”.
The fuse is blown.
Replace the fuse.
The unit turns on,
but has no sound.
Volume is on minimum
Adjust volume to a desired level.
Audio wiring is not properly
connected.
Check wiring connections to preamp
outputs, speakers or both.
The buttons on
the unit do not
respond.
The built-in microcomputer is
not operating properly due to
noise.
Press the reset button on the front
panel.
The radio does
not Work. The
radio station
automatic
selection does not
work.
The antenna cable is not
connected.
Insert the antenna cable firmly.
The signals are too weak.
Select a station manually.

SPECIFICATIONS
15
FCC Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a mobile
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
This equipment complied with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 20cm between the radiator & your body.
WARRANTY
Maxxsonics USA Inc. warrants this product, to the original consumer purchaser, to be free from defects in material and
workmanship for a period of one (1) year from the date of purchase. Maxxsonics USA Inc. will, at its discretion, repair or
replace defective products during the warranty period. Components that prove to be defective in materials and
workmanship under proper installation and use must be returned to the original authorized Maxxsonics USA Inc. retailer
from where it was purchased.Aphotocopy of the original receipt must accompany the product being returned. The costs
associated with removal, re-installation and freight are not the responsibility of Maxxsonics USAInc. This warranty is
limited to defective parts and specifically excludes any incidental or consequential damages connected therewith. To
view the full warranty, please visit the website.
The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use such
marks by MB Quart is under license.
All product names, logos, and brands are property of their respective owners.All company, product and service names
used in this literature are for identification purposes only. Use of these names, logos, and brands does not imply
endorsement.
©2019 Maxxsonics USA, Inc.
MBQuart products are designed and engineered in the USA by
www.maxxsonics.com
Rev_1.0_5-2-2019_FINAL